Search Documents

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007

By Bruce Clements

The Bagdad mill, located near Bagdad, AZ, was built in 1977 with a designed mill capacity of 36.3 kt/d (40,000 stpd). An autogenous mill-ball mill crusher (ABC) grinding circuit was chosen. The original mill contained three independent grinding circuits. Each contained one 9.75m-diam x 4-m-long (32-ft-diam x 13-ft-long) fixed-speed autogenous mill, a4.7-m-diam x 6.7-m- long (15.5ft-diam x 22-ft-long) ball mill and one 2. 1-m-diam (7-ft-diam) short head cone crusher. Total installed power per grinding circuit was about 8.4 MW (11,350 hp), with 5.9 MW (8000 hp) in the autogenous mill, 2.2 MW (3000 hp) in the ball mill and 261 kW (350 hp) in the crusher (Fig. 1). The autogenous mills were designed to be able to operate semi-autogenously. However, they were never converted to semiautogenous grinding (SAG) mills. As a result of this design, only about 4.1 MW (5450 hp) of the designed power is used in the autogenous mills. The grinding circuits are closed, with 2.4 x 6 m (8 x 20 ft) double-deck vibrating screens. A series of conveyors re- turn screen oversize underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt (Fig. 2). A magnetic sensor detects tramp iron in the autogenous mill-crusher circuit.

Jan 1, 1992

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

By B. K. Mishra

In order to maintain higher grinding efficiency in tumbling mills the mill interior and dynamics must be known. For this purpose, several different types of non-intrusive methods have been proposed and are being tried in the industry. We have made an effort to develop a diagnostic tool based on vibration signal. Here we discus results of our experiments pertaining to ball as well as SAG mill. In each case, a triaxial accelerometer was used to capture mechanical vibration generated due to the tumbling action of the charge. The vibration signal was transmitted to a remotely placed computer and the signals were analyzed by standard signal processing technique. In case of a ball mill (5m diameter), qualitative mill information could be obtained by correlating the vibration signal to feed rate and mill filling. An effort was also made to identify different motion characteristic of the charge by analyzing its vibration signal. In case of the SAG mill (10m diameter), liner wear was estimated by comparing the vibration signal emitting out of a freshly lined mill with that of a worn out mill.

Jan 1, 2011

By D. Dunbar

Flooding of open pits now receives considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit lake deep waters can effectively eliminate oxidation of pit-wall sulphides. A state-of-the-art, coupled physical-geochemical pit lake model is used to verify that a cost-effective, environmentally responsible closure strategy for the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia is to adopt a controlled, two-stage infilling of the open pit upon cessation of operations. By filling the pit initially with highly saline waters from evaporation/infiltration basins and naturally saline deep groundwater, followed by capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within 1 to 2 years, followed by the rapid onset of sulphate reducing conditions in the bottom waters. Hydrogen sulphide produced by sulphate reduction will readily react with dissolved metals to form highly insoluble metal sulphides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental management strategies. The proposed plan allows for: 1) safe storage of saline evaporation basin waters; 2) the potential for passive treatment in anoxic bottom waters of ARD seepages from other mine site operations should they arise; and 3) a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2001

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

By R. Fernández, E. Marczak, A. Collins

Newmont roasting plant in Carlin, Nevada commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable that affected the structural characteristics of the calcine which, in turn, affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature was closely monitored since October 2000. Original design temperature was 550oC. Lower roaster temperatures of around 500oC resulted in gold recovery increase by more than 6 percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an “intelligent” process control system helped significantly in achieving steady low roasting temperatures thus achieving high gold recoveries between 92 and 93 percent. Under those conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease of gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g. porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2007

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

By Don C. White

The Vulture mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11t(12.1 st) Au and 8t (8.8st) Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely dis¬seminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence, all dipping north about 35°. Early mining focused on the vein-hosted gold, particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pit mining of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry. The sill is a 350 m (1148 ft) long apophysis from a quartz mozonite stock to the west of the mine area. The stock has been dated at 85 my and contains abundant lesser gold occurrences in its core and about its margins. The Proterozoic rocks are notably lean in precious metals except where altered in proximity to the Creataceous stock and sill. Circumstances dictate an interpretation of epigenetic mineralization related to the Laramide intrusion.

Jan 1, 1990

By S. Klein, D. Crouthamel, D. W. Farmer, S. H. Phillips

Groundwater inflows during construction pose one of the greatest risks to the successful completion of tunnel projects. Inflows can result in safety concerns, difficulty in mining and ground support, impact sensitive environmental habitats, create surface settlement and increase costs. Adequately planned pre-excavation grouting programs benefit both the Owner and Contractor in reducing risks and controlling project costs and potential schedule delays. This paper outlines strategic guidelines for assessment of site conditions for pre-excavation grouting hard rock tunnels. It also describes the design of pre-excavation grouting programs with respect to project requirements.

Jan 1, 2005

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By George H. K. Schenck

In this decade of the 1.970's it is forecast that eight billion cubic yards of rock will be excavated from 400, 000 miles of new tunnels, drifts and other underground workings in the western world, according to estimates in a report of the Organization for Economic Cooperation and Development (OECD). It is expected that the cost of this work will be in excess of $54 billion in constant 1970 dollars. Most of this underground excavation will be in mining -- 97% of the tunnel length and 89% of the volume - -the balance in construction. In addition to this huge excavating task, in the 18 developed nations of OECD, will be projects in the Communist Bloc and in the developing nations. Underground excavation requires the successful completion of three principle activities: A. Break -- to free rock from the solid work face. B. Remove-- to clear the work area of broken rock. C. Support -- to assure stability of rock surrounding the underground excavation and to eliminate risk of rock collapse. In today's fully mechanized excavation systems, continuous miners, roadheaders or tunnel borers, (A) break the rock loose from the face, and (B) remove broken rock with their mucking devices and load it onto belt conveyors, mine cars, trucks, or any other appropriate haulage system for disposal. Such operations contrast to the more complex, intermittent systems employed when

Jan 1, 1974

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013