Search Documents

By C. D. Hebert, M. R. King

The 56,000' (17 km) long San Vicente Aqueduct Pipeline tunnel is being constructed using precast concrete rings to act as preliminary ground support through two sections of the bored tunnel with lengths of 9,450' (2.9 km) and 33,700' (10.27 km).The six segment bolted trapezoidal ring was manufactured using a combination of steel fiber reinforced concrete and self compacting concrete in vertical moulds. This paper briefly describes the design and function of the segments, and reviews the development stages of the concrete mix, and the advantages and disadvantages of the adopted manufacturing method.

Jan 1, 2007

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By Darrell Gillis

Recent accidents in the United States underground Coal Mines and the on-going carnage in Underground Chinese Coal Mines has shown the danger associated with the lack of communication infrastructures in an underground environment. The US Mine Safety and Health Administration (MSHA) have introduced legislation that states all Underground Coal Mines must have two-way voice and personnel tracking capabilities by 2009. If Coal Mining companies are being forced to deal with this problem Tunneling Companies will not be far behind. This paper will examine current practices and best case technology to deal with these issues.

Jan 1, 2007

By J. C. Fox, V. L. Ketellapper

The Summitville Mine, located in the mountains of Southwest Colorado, is an abandoned gold mine. From 1984 to 1992, Summitville was mined for gold using an open pit heap leaching technology. During this period, the volume of acid mine drainage released from the mine significantly increased. This was attributed to the development of the mine pits, the waste rock piles, the heap leach pad, and increased discharges from the drainage adit. The release of this acid mine drainage resulted in the destruction of the aquatic ecosystem for more than twenty miles downstream of the mine. Beginning in 1993, plans were implemented to reduce the amount of acid mine drainage released from the mine. The majority of this work has been completed at the mine. This work includes removal of the Cropsy Waste Pile, closure of the Heap Leach Pad, and revegetation of disturbed areas. Significant improvements to water quality downstream of the mine have occurred resulting from mine reclamation. Aquatic life has returned to portions of the previously mining impacted areas. This study discusses the actions taken to reduce the amount of acid mine drainage generated at the Summitville Mine, the costs of these actions and the resulting reduction in metal loadings. Over 250 samples taken at over 10 locations since 1993 form the basis of this evaluation. Copper loading is analyzed as an indicator of the effectiveness of the actions taken.

Jan 1, 2002

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC&apos;s lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today&apos;s fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

Despite limited discussion, Chemistry of Flotation is a good text and reference 1985 by M. C. Fuerstenau, J. D. Miller, and M. C. Kuhn Society of Mining Engineers Caller No. D Littleton, CO 80127 Softcover, $23.50 (member), $18.50 (student member), $28.50 (list) Review by Richard R. Klimpel Chemistry in Flotation, as stated by the authors, is intended as a textbook for students as well as a reference book for practicing flotation engineers. It covers subject matter related to surface phenomena; collectors and collector salts; natural floatability; the flotation of sulfide minerals, insoluble oxide and silicate minerals, semisoluble salts, and soluble salts; and slime coatings. There are no discussions in the book on practical plant implications of flotation chemistry, such as the influence of rate, particle size effects, dosage, flotation equipment, and methods of chemical addition. The book itself is small (only 177 pages), and, as published, is in an easy-to-handle soft cover. Once one accepts the intent of the authors, this book really does represent a very concise and convenient summary of the chemistry of flotation. It is, however, far from complete in its discussion of concepts and implications of data. Very often in the presentation, key prior knowledge (or at least subject matter awareness) not given in the book, is assumed. Thus, depending on one&apos;s familiarity with the specific subject matter, some sections can be easily followed while others could be tough going. Some of the discussion is so brief and terse on important subjects that unless the reader already realizes the meaning of the presentation, the conclusions to be drawn are not always clear. Therefore, if one is not expecting a self-contained primer on flotation chemistry, this book is very useful. To this end, the book is recommended to practitioners of flotation chemistry. The presentation of data in figures and tables is good. It helps considerably in the book achieving its conciseness. The authors certainly are qualified and knowledgeable in the subject matter - apparent in the style of presentation. In summary, this reviewer thoroughly enjoyed this book and will use it as a concise review of flotation chemistry. Richard R. Klimpel, member SME, is a scientist with Dow Chemical Co., Discovery Development, 1776 Building, M. E. Pruitt Research Center, Midland, MI 48640. International Symposium on Blast Furnace Ironmaking, 1985, The Indian Institute of Metals, The Tata Iron and Steel Co., Ltd., Jamshedpur 831007, India, 282 pp., papercover, no price given - Papers from this symposium held in Jamshedpur, India, include the following: determination of coal and coke quality; feed to blast furnaces; burden quality and blast furnace performance; operation of blast furnaces on charcoal; review of cast house slag granulation systems; developments in blast furnace engineering and control; process improvements in blast furnace ironmaking; coal injection into the blast furnace; and coke from stamp charged coal. Advances in Materials Technology for the Process Industries, 1985, edited by H.A. Huskins, National Association of Corrosion Engineers, P.O. Box 218340, Houston, TX 77218, 273 pp., softcover, $20-This book is the proceedings of a meeting held in Atlanta, GA in October 1984. It describes innovations in metallurgy, ceramics, glass, composites, and polymeric materials that impact the integrity and economics of operating systems. It covers biotechnical developments, improvements in membrane systems, or beneficiation processes, as well as developments in electrochemical controls, testing procedures, and surveillance techniques. A Reference Guide to Mining Legislation in Canada, 1985, by B. Barton, B. Roulston, and N. Strantz, The Canadian Institute of Resources Law, Room 430, Bio Sciences Building, The University of Calgary, Calgary, Alberta, Canada T2N 1N4, 120 pp., bound, $US28- This guide provides a ready means of finding how the different jurisdictions in Canada regulate mineral activity. It covers the rights required for exploration, development, and production of mineral metallics and industrial minerals. It does not cover placer mining, petroleum and natural gas, bituminuous sands, coal, or structural materials. Dictionary of Geological Terms, 1985, edited by Robert L. Bates and Julia A. Jackson, The American Geological Institute, 4220 King St., Alexandria, VA 22302, papercover, $7.95 plus $1 for postage - This third edition is for geoscience students, teachers, and rockhounds. It defines the core vocabulary of earth sciences, contains 8000 revised definitions, and includes 1000 new terms. It adds recent terms in plate tectonics, hydrology, and permafrost studies. Accurate definitions are given without technical jargon, cross-references are included, and commonly used abbreviations are provided. Processing and Utilization of High Sulfur Coals, 1985, edited by Yosry A. Attia, Elsevier Science Publishing Co. Inc., 52 Vanderbilt Ave., New York, NY 10017, 787 pp., bound, $142.50-These proceedings comprise the majority of the papers presented at the First International conference. Investigators there reported the latest discoveries, developments in commercial practice, and state-of-the-art reviews of scientific principles and applications of various technologies for handling, processing, and use of high sulfur coals. Sessions were held on: characterization of sulfur in coals; environmental problems and impact of high sulfur on coal use; selective mining and blending; coal desulfurization by physical and chemical cleaning techniques; handling of coal fines; sulfur capture during coal combustion; biological desulfurization of coal; and new applications for high sulfur coal. The Economics of Magnesium Metal, 1985, Roskill Information Services Ltd., 2 Clapham Road, London SW9 OJA England, 129 pp., 71 tables, appendices, bound, $750-Despite setbacks in some major magnesium markets in 1985, Roskill&apos;s latest forecast for the last half of this decade is for a 4% to 6% annual growth rate in demand. Growth for magnesium metal is expected in the motor industry for use as a possible substitute for aluminum. Some magnesium producers are altering their marketing strategies to cultivate this market. This study also includes a review of the worldwide magnesium industry, its end uses and consumption, and international trade and price trends.

Jan 7, 1986

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990&apos;s. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18&apos;-11" OD Brooklyn Tunnel; the 5-mile long, 23&apos;-2" OD Queens Tunnel, and the9-mile long, 12&apos;-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007

By James M. Riddle

A discussion of frequently asked questions may help individuals trying to interpret subsidence regulations or prepare permit applications. The subsidence permitting process involves just one part of the mass of Surface Mining Control and Reclamation Act regulations. But of the 18 main SMCRA sections, subsidence is critical to the permitting process for coal operators. It&apos;s an area in which applicants have had problems interpreting regulations and preparing permit applications. Of 22 western states, only Wyoming, Montana, Colorado, and Utah heave thus far received approval for their mining and reclamation plans. The other states are now involved in the permit application process and will be dealing with SMCRA regulations for the next year or so. Some state programs, when approved, may differ substantially from the federal SMCRA program. But, to be approved, the state programs must be deemed equal to or more stringent than the federal regulations. SMCRA regulations apply to any coal operation "that exhibits surface effects." Thus they apply to surface strip mines as well as underground coal operations. The regulations do not apply to hardrock mining operations. Since August 3, 1977, the government, industry, and the public have wrestled with SMCRA. They have struggled through an initial program with the US Geological Survey; a new agency, the Office of Surface Mining Reclamation and Enforcement (OSM); an interim program; and a "final" permanent regulatory program. Even now, OSM is reluctant to publish formal program guidelines because: •The regulations are still in the process of judicial review. • Some approvable state programs will supersede the federal regula¬tions. • The flexible regulations are open to interpretation, which is desir¬able to maintain. •Guidelines could be misleading until regulations and interpretations are revised and finalized.

Jan 12, 1980

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump&apos;s best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"&apos; BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By Bart Bartholomew, Randall J. Essex

INTRODUCTION In June of 2004, at the North American Tunneling Conference in Atlanta, an all-day workshop was conducted to review the application of Geotechnical Baseline Reports (GBRs) for underground construction. The moderator for the program was Bart Bartholomew, former President of Fruin Colnon Construction Company. The program involved commentary by a panel of engineers, owners, contractors, and legal representatives within the North American tunneling industry, as well as an extended audience discussion. The panelists were: Peter Douglass, President, Peter Douglass, Inc. Randall Essex, Executive Vice President, Hatch Mott MacDonald Joseph Gildner, Deputy Director for Technical Services, Sound Transit Randall Hafer, Esq., Kilpatrick Stockton Robert Fitzgerald Esq., Watt, Tieder, Hoffer, & Fitzgerald Kirk Samuelson, Senior Vice President, Kiewit Construction Group DEVELOPMENT OF PROGRAM FORMAT The focus of the program was to assess the state of the practice in the preparation of GBRs, and to discuss improvements that could and should be made with regard to their preparation, interpretation, and application. The approach used to achieve this focus in the broadest possible way was unique, in that it involved the panelists’ preparation of the workshop format and materials months before the presentation of the workshop. First, each of the six panelists was selected by the moderator based on their reputation and involvement in their respective fields of expertise, taking care to maintain balance and contrast within the collective pool of talent assembled. Following selection and agreement to serve on the panel, each panelist was asked to independently submit to the moderator a list of the six most pressing issues involving GBRs that they each frequently encountered in their individual professional experience. Each was asked to rank their issues in descending order of perceived importance. This process resulting in a pool of thirty-six potential or “candidate” issues for use in the workshop program. Contrary to the moderator’s expectations, there was surprisingly little duplication among the thirty-six issues submitted.

Jan 1, 2005

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

By T. S. Golosinski

Introduction Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost. Both work in very difficult conditions and wear out rapidly. As a result, frequent rope changes are required resulting in substantial cost and productive time loss. Although performance of rigging has a profound impact on dragline efficiency, there are no common, industry accepted standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The performance of drag and hoist ropes depends on: •rope construction that should closely match requirements of the specific application, rope operating conditions and its maintenance and • correct definition and application of the rope discard criteria so that full advantage of the rope can be taken without endangering safety of its operation. This paper reviews the present practice related to all these factors. Its findings are based on the wide survey of the present industrial practice. Field survey In total, 33 North American dragline applications were surveyed of which 17 were Bucyrus-Erie machines, 10 were Marion and six were Page (now P&H). Most of the draglines were stripping overburden in coal mines, but the survey also included some unique applications such as phosphate mining in Florida and oil sand mining in Alberta. Hoist drive power of the surveyed machines varied from 300 to 7775 kW (400 to 10,400 hp). Drag drives varied from 300 to 5815 kW (400 to 7800 hp). Boom lengths varied from 37 to 110 m (120 to 360 ft). Bucket sizes varied from 5 to 96 m3 (6 to 115 cu yd). The hoist and drag ropes installed on the surveyed machines were supplied by 10 rope manufacturers and differed widely in type and construction. Most common rope strand constructions included standard strands, Seale, Warrington, Warrington-Seale and Filler-Seale. Results of the survey [ ] Working conditions Working conditions of hoist and drag ropes are quite different. The first cope primarily with bending on rope drums, point sheaves and deflection sheaves, and with tension force imposed by the bucket and its load. The drag ropes are exposed to severe abrasion at the pit crest, and to severe bending and crushing at fairleads, all while coping with tension forces imposed by resistance of the bucket to dragging. Bending of drag ropes at house rollers and at rope drums is of minor importance for their performance. Differences in working conditions result in different wear patterns, which make it feasible to install discarded hoist ropes to further serve as drag ropes. The hoist ropes wear primarily due to fatigue breaks of wires, while the drag ropes are subject to severe abrasion of outside wires, rope deformation and internal wire-strand breaking. The last is often indicated by the reduction of rope diameter. The summary of working conditions for the surveyed draglines is shown in Table 1. For simplicity, Table 1 does not include the data on rope bending at the fairleads, nor at the deflection rollers and house rollers. Similarly, Table 1 does not include the data on drag rope bending (other than that on the rope drum), as its influence on rope life is insignificant in view of severe abrasion and internal wear taking place elsewhere. The following abbreviations are used in Table 1: [D - diameter of rope drum. DP - diameter of boom point sheaves. d - rope diameter x - mean value of the measured parameter. s - standard deviation of x B/d - average bending ratio of ropes B/d =(D+ DP)/2d n - operational safety factor of the rope (rope stength) x (number of ropes) n(bucket load + bucket weight)] In terms of D/d ratio, the working conditions of hoist and drag ropes are similar to that in other related industrial applications. However, the safety factors of the dragline ropes are lower, which requires them to carry relatively large tension forces. The last explains the fact that the life of dragline ropes is low when compared to other industrial rope

Jan 1, 1995

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By T. Lamond, J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870&apos;s with rising national wealth and declined in the 1950&apos;s when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000