Search Documents

By B. K. Loveday

The South African Institute of Mining and Metallurgy hosted a School on 'The Practical Design of Comminution Processes' at Megawatt Park (near Johannesburg) on 14th to 16th May, 1991 Derek Barratt, a Senior Consultant of Wright Engineers, Canada, and the main speaker, provided a good insight into how Wright Engineers design milling circuits, particularly large semi-autogenous mills. He was ably assisted by Jens Lichterof Allis Mineral Systems, who described some interesting examples of pilot-plant testwork and summarized South African milling practice. Mike Moys of the Witwatersrand University spoke on the influence of pulp viscosity on mill performance, and Johan Engelbrecht and Jeremy Bosman of Multotech

Jan 1, 1991

The following letter has been received from Professor P. A. Young, Head of the Department of Mining and Mineral Engineering at The University of Leeds, England. Extractive and process metallurgy The first annual TMS-AIME Extractive and Process Metallurgy Fall Meeting:1983 International Sulfide Smelting Symposium, will be held from 6th to 9th November, 1983, in San Francisco.

Jan 1, 1982

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

By I. R. Firth, D. L. Taylor

Metal mining operations, in particular gold mining operations, use intensive ore control procedures in order to manage the extraction of ore zones from benches containing both ore and waste material. Typical grade control procedures rely on blast hole samples to indicate ore grade. Statistical techniques and geological controls are then used to create two-dimensional polygons, which indicate zones of material designated as ore. These ore-polygons are calculated using pre-blast material locations and are generally not corrected for rock movement caused by blasting. This lack of correction appears to exacerbate the material mischaracterization problem of sending ore to the waste dump and/or waste to the mill. One Nevada gold mining company has estimated that this could be a $10 million per year problem for their operations. Using a simplified vector field algorithm, a method of taking point movement data and interpolating post-blast positions for all nodes in a polygon has been developed. Currently working in 2-dimentions (X-Y), this algorithm utilizes the movement vectors calculated from pre-and post-blast positions of targets placed in a blast, to generate a spatial transformation function for any point on the bench. This transformation is then applied to the nodes of the ore-polygons to produce modified dig lines ore polygons reflecting distortion and movement resulting from the blast. The method as implemented uses common mine planning routines and is performed using the Surpac software suite. The method may be adapted to use any pre-and post-blast point movement data available, and most mine planning suites include the simple interpolation algorithms used. Keywords: Blast movement; Ore control; Open pit blasting; Grade control

Jan 1, 2003

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

Pyrometallurgy has played a very important role in southern Africa for at least four centuries. It continues to do so, and recent years have seen many exciting developments in pyrometallurgical technology. The wonderfully diverse rich mineral deposits in this area of the world have provided some unique opportunities for industrial processes to be established. The ?Southern African Pyrometallurgy 2006? conference was set up to showcase southern African pyrometallurgical operations, and to provide a forum for the exchange of ideas between people working at various types of smelters. Papers have been obtained from a wide variety of pyrometallurgical plants in southern Africa. These descriptions of plant operations (as well as some history, and highlights of current work) will provide useful reference information for some time to come. Contributions are also included from universities, research organizations, and engineering companies, so that the full spectrum of pyrometallurgical activities can be covered. The plant descriptions will be published on a website, where they can be updated as and when required, with the eventual goal of having a description of every smelter in the region. The conference venue was selected to be the 'Cradle of Humankind' world heritage area, about 40 km from Johannesburg. Not only does this keep the conference within easy reach of the city and yet far enough out into the countryside to allow people to focus on the conference, it is also within easy reach of many pyrometallurgical plants. There is a particular significance to the choice of location, in that the Swartkrans area close to the Sterkfontein Caves is the site of the earliest evidence of the deliberate controlled use of fire by human beings (about 1.3 million years ago), and this is obviously a necessary precursor to pyrometallurgy. The area also lends itself to a very wide range of outdoor, social, and cultural activities to supplement the technical content of the programme. It is hoped that activities such as a hot air balloon safari and visits to the world-renowned Sterkfontein Caves and Wonder Cave will help to make the conference a memorable one for those able to attend. I trust that the ongoing value of the papers and presentations will make all the hard work of the many contributors most worthwhile.

Jan 1, 2006

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By C. E. Hales

In an effort to improve efficiencies and reduce costs, AngloGold has embarked on a process to develop and deliver consistent, high quality, tailings based support or construction products to stopes and tunnels on request. A three-phase approach of product conceptualisation, design and delivery has been adopted. To date a substantial amount of laboratory development has taken place with promising results, indicating that the project aims are achievable. Dans un effort pour améliorer le rendement et réduire les coûts, AngloGold s’est embarqué dans une opération qui vise à développer et fournir aux chantiers d’extraction et tunnels, sur demande, des produits de construction ou de support basés sur rejets qui sont réguliers et de haute qualité. Une méthode à trois volets a été adoptée : conception, création et livraison. A ce jour, un développement important en laboratoire s’est produit, avec des résultats pleins de promesses, qui semblent indiquer que les buts du projet peuvent être atteints. In der Bemühung, die Effizienz zu steigern und Kosten zu verringern, hat AngloGold begonnen ein Verfahren zu entwickeln welches auf Anfrage konsistent hochqualitative auf Haufwerk basierender Unterstützung oder Bauprodukte für Abbaustellen und Tunnels entwickelt und liefert Eine Dreiphasenplan zur Produktkonzeptualisierung, Design und Lieferung wurde adoptiert. Bis jetzt hat eine substantielle Anzahl an Laborentwicklung mit vielversprechenden Resultaten stattgefunden und aufgezeigt, daß die Projektziele erreichbar sind.

Jan 1, 2003

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

Keywords: Pyrometallurgy, Wits University, research Wits Metallurgy celebrated its centenary in 2004. The department has been at the forefront of education and research and has contributed greatly to the metals and minerals industry, both in South Africa and abroad, in terms of human resources and knowledge generation. A significant number of industry and academic leaders worldwide are Wits Metallurgy graduates. Since its early beginnings, pyrometallurgy has always been part of the curricula and research offered by the department. Pyrometallurgical activities started to expand tremendously from the middle of the 1960s, especially by the formation - together with Mintek - of the Pyrometallurgy Research Group, which continues its internationally recognised research activities today. The research efforts have been concentrated on problems associated particularly with ferroalloy, steel, stainless steel production, and PGM/Cu-Ni sulphide smelting. In recent years, research has been further expanded to physical modelling of pyrometallurgical reactors. Almost all of the specific research projects were handled from a fundamental point of view, and hence a large number of MSc(Eng) and PhD degrees were achieved by candidates under the supervision of the Pyrometallurgy Research Leaders. Moreover, a significant portion of the research results were published in internationally recognized journals and conference proceedings. Among these, Infacon and the Molten Slags, Fluxes and Salts Conference series are worth mentioning. The studies from a fundamental point of view include thermodynamics, phase equilibria, transport phenomena, kinetics, and process dynamic aspects of high temperature processes and systems, both in the solid and liquid states.

Jan 1, 2006

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l'Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l'index RMR ont été exigés. SRC et des index RMR et d'autres données geomechanical appropriées ont été obtenu pendant l'enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d'accent) in situ, l'analyse de structures tectoniques et des problèmes d'instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l'état de stress(d'accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d'appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l'index RMR.

Jan 1, 2003

By Baojun Zhao

Primary lead production using the lead blast furnace in conventional practice is carried out using sinter feed. At YMG, China, the sinter plant has been replaced with a lead ISASMELT furnace. The ISASMELT furnace produces lead bullion plus a high-lead slag, which is cast into lumps to provide a suitable feed for the blast furnace. In the present study the relative microstructures and reduction characteristics of industrial lead sinters and synthetic ISASMELT slag in CO/CO2 gas mixtures have been measured and compared. The microstructure and property changes, and the mechanisms of reduction in each case are examined and discussed. The results of the study are used to explain the successful implementation of cast slag feed in commercial ISASMELT- lead blast furnace practice. Key words: lead slag, lead sinter, lead blast furnace, reduction kinetics and mechanisms

Jan 1, 2008

By M. Yavuz

Equipment selection in mining operations is an important issue, and also difficult to solve in multiple criteria environments. The paper in question has aimed to develop computer software for solving equipment selection problems in mining. In their paper, Basçetin et al. have analysed two case study problems related to open pit and underground mining method selection. By using Yager?s method1, the authors have selected 18 different criteria in the first case study and 21 criteria in the second case study. However, as emphasized by Ozdemir2, in pair wise comparison matrices the appropriate number of criteria should be seven as the maximum, from the point view of validation, consistency and redundancy. In cases where there are more than seven criteria to be handled, it is suggested that the criteria should be clustered and then the maximum number of clusters and subcriteria of every cluster should be limited to seven4.

Jan 1, 2007

By W. Mackenzie

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines - mining, metallurgical, chemical, civil, electrical, mechanical and environmental - as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies - and hence no two development projects - are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource project's development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as `doing a feasibility study'. But the principal purpose of a `feasibility study' is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant - they are a prerequisite to the demonstration of a project's viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of `feasibility studies' and provide guidance to minimum standards and best practice.

Jan 1, 2007

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely: codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage like nuclear power generation where international cooperation is eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit their mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2003

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By G. Vouille, P. Bérest

Residual stresses observed in rocks often result from non-compatible initial strains. These stresses can be determined when the incompatibility tensor associated with the initial strain tensor is known. The residual stresses in a cylindrical rock sample can be computed the sample is considered small enough for its incompatibility tensor to be constant. Les contraintes résiduelles, dont on observe couramment les manifestations dans les roches, résultent souvent de l’existence de déformations initiales non-compatibles. Ces contraintes peuvent être calculées lorsque le tenseur d’incompatibilité associé aux déformations initiales est connu. Les contraintes résiduelles dans une éprouvette cylindrique sont données dans le cas où le tenseur d’incompatibilité est constant. Eigenspannungen, die man haeufig in Steinen beobachtet, sind oft Ergebnis einer inkompatiblen Deformation des Anfangszustandes. Diese Spannungen koennen berechnet werden, wenn der Inkompatibilitaets-Tensor der Anfangsdeformation bekannt ist. Die Eigenspannungen einer zylindrischen Probe werden fuer Fall eines konstanten Inkompatibilitaets-Tensor bestimmt.

Jan 1, 2003