Search Documents

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow in by the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By Ronald F. Balazik

[This Bureau of Mines study is intended to identify and evaluate potential effects of impending large-scale U. S. rail line closings (abandonment) on domestic nonfuel mineral industries. This is the first nationwide study of rail abandonment impacts focused on nonfuel minerals. The analyses presented is based principally on a survey of 200 rail freight records and on statistical tests that correlated 2,000 points in the Bureau's Mines Industry Location System (MILS) with 700 prospective abandonments throughout the United States. The conclusions derived from the analysis can be useful in evaluating proposed national rail abandonment policy rind legislation regarding nonfuel miner it shipping. Among these conclusions are the following: (1) Certain mineral materials (especially fertilizers) are likely to account for a large percentage of the rail traffic affected by abandonment in the next few years, but the total tonnage- involved will be small; (2) abandonment will adversely affect some mineral shippers, particularly local smart haulers; and (3 abandonment could significance reduce the opportunity to develop new resources or reopen defunct mining facilities. Despite these problems, however, the data examined in this study do not indicate that current abandonment trends will cause widespread disruption 01 domestic nonfuel mineral shipping.]

Jan 1, 1980

By James R. Aggson

This Bureau of Mines report describes floor heave ground control problems that have been encountered in a new underground coal mine in West Virginia. Previous experience in the coal seam, the results of physical property investigations, and in situ rock stress determinations are discussed. The apparent cause of the ground control problems is the existence of a high, biaxial, horizontal stress field coupled with a floor member that has time-dependent deformation characteristics, A theoretical analysis of the failure process is developed. The analysis is assisted by finite element techniques. Mine design recommendations based on this analysis are presented.

Jan 1, 1978

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By George H. Johnson

This report describes the procedures and summarizes the results of an investigation of surface subsidence above caving blocks at the San Manuel mine, San Manuel, Ariz., in order to obtain quantitative information on subsidence and ground movement caused by mining large volumes of ore. This investigation is one part of an overall study of rock mechanics being undertaken by the Bureau of Mines. Attention was given to the improvement of a rapid and precise method of surveying a large number of subsidence pins and cracks in the surface terrain. Photogrammetric methods were used as an adjunct to the triangulation subsidence surveying as well as in ordinary topographic work Maps of various kinds were prepared to show the results obtained. The computation of the survey notes was programed for an electronic digital computer at a saving of time and expense over the use of a desk calculator and trigonometric tables.

Jan 1, 1963

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976