Search Documents

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

By S. K. Ash

In arriving at economic losses in coal mining due to accidents, a statistician is confronted with many difficulties on account of the lack of information relative to nonfatal accidents. For comparative purposes the ex¬ perience of those countries, States, or companies that keep complete records can be drawn upon and an extimate can be arrived at whereby one State can be compared with another, or one mine compared with another in the same district. Such a comparison for the United States has been compiled by the United States Bureau of Mines. It will be observed in Table 1 that the cost per ton for accidents in the State of Washington for the year 1927 is higher than for any other State, with the exception of Georgia and North Carolina, with a small combined tonnage of 130,089 tons. (The figures for coal production in Table 1 are taken from Bulletin 319, 1930, of the United States Bureau of Mines.) The reasons why the cost of accidents in Washington might be higher than the average are on account of physical conditions such as steep pitches, faults, igneous intrusions, highly explosive coal-dust, extremely friable coals, presence of gravel and water, very gassy coal beds, rugged topographic conditions, inherently bad roof and floor, thick beds, and heavy cover. The nature of the coal beds requires the use of preparation machinery. The mines are often deep, and topographic conditions are such that long and fast haul¬ age becomes necessary. All of these factors not only tend to cause high cost of production, which is manifested largely in a. lower than average daily pro¬ duction, per man, but..they.also affect to some degree a tendency toward a higher than average cost for accidents.

Nov 1, 1931

By Charles J. Cohen, Donald F. Reed

"INTRODUCTION AND ACKNOWLEDGMENTSThis report supplements a previous report on work done in this same area 4/ but covers only the period from November 1945 to November 1946. The project was established in 1943 to investigate magnetite deposits in the northwestern Adirondacks by geophysical surveying and diamond-drilling for the purpose of increasing iron production in the eastern United States.In its program of investigation of mineral deposits, the primary objective of the Bureau of Mines is the more effective utilization of our mineral resources, that they may make the greatest possible contribution to our national security and economy. The policy of the Bureau is to publish the facts developed by each project as soon as possible after its conclusion. Maps showing the detailed magnetic surveys of the deposits and anomalies discussed in this report are on open file at the offices of the Bureau of Mines, College Park, Md., and at the University of the State of New York in the office of the Director of the State Science Service, Educational Building, Albany, N. Y.The Mining Branch, Lowell B. Moon, chief, conducts preliminary exami¬nations, performs the actual investigations, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical analyses included in this report were made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under, the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, in charge of the laboratory service unit."

Nov 1, 1947

By W. D. Mcmillan

Preliminary examination of the north-central Kansas clay deposits was made by the junior author during March 1943. He was accompanied by Norman Plummer, ceramist of the State Geological Survey of Kansas. Three areas Nacre selected for further investigation. Detailed field investigation by the Bureau, consisting of hand auger drilling, trenching, anti. test pitting to obtain representative samples of the clays was carried on from April to June 1943. Field .work was under the direction of Edgar B. Butte and Richard L. Schumacher, former Bureau of Mines engineers. The samples taken were analyzed at the Bureau of Mines laboratory at Rolla, Mo. Factual data obtained from the field investigation and laboratory work are set forth in this report.

Jan 1, 1948

By W. W. Adams

[The s1xteeilth an.nual National Safety C mpeti t1on, concluc ted "by the Bureau of t4ine g, Un+ ~ed st tag' DepartIilent 0:1' the Interior, has jast been closed, and the results reveal t:'W.t. t_!e co~)eting comps.nies had fewer a.ccidents in proportion to the number. of !\1a..."1-h(J1J.l'~ :orkcd than in a:ny other yeex in the record of the contest. These annUk~l contestn are thus achieving the r purpose of promoting safety in tho minin induC'tr:r. ]

Jan 1, 1941

By R. A. Busch

Sludge ponds of fine coal, fine soil, and water created behind large piles of coarse coal waste can present hazardous conditions; this is a Bureau of Mines report of the subsurface physical property data developed on the fine coal waste materials that make up the core areas of two typical coal waste impoundments. These data will help define more completely the engineering properties of this problem area of the structures. Additional calorific, chemical, and mineralogical data were obtained on the coal waste materials to determine possible uses or development of byproducts. The possibility of extracting alumina from coal ash was also investigated.

Jan 1, 1975

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

By E. R. Palowitch

Coal wasted with mine refuse represents losses in overall recovery of merchantable coal to the mine operator and a concomitant reduction in domestic reserves of available coal. Fraser, Kelley, and Graham3/ in studying the available coal in mine refuse in the Pittsburgh district of western Pennsylvania have estimated that at least 1 ton of mine refuse is produced for each 10 tons of merchantable coal and that 20 percent of this mine refuse might be recovered as salable coal by mechanical cleaning. SUMMARY This investigation dealt with the mechanical recovery of coal from wine refuse by a dense-medium washery employing pulverized mine rock as the dense medium and operating at a rate of 175 tons per hour. Two types of mint refuse were tested: Freshly mined and that .which had been mined 2 years before and piled on a waste dump.

Jan 1, 1955

By F. A. Patty

[Health and safety hazards from contamination of the atmosphere in places frequented by persons depend to a considerable extent on whether the contaminating agent possesses sense-perceptive properties which will give warning of its presence before it '.an create harmful conditions. If a distinct and easily recognized warning is given in advance of harmful conditions, hazards ace mitigated, but if warning properties are inadequate or absent, the hazards are augmented. When evaluating the hazard presented by a potentially harmful substance used under conditions of possible escape into the air of places frequented by persons, it is therefore necessary to consider the warning properties of the substance along with ether pertinent information such as toxicity, inflammability, physical properties, and mode of use. If the contaminating agent inherently lacks warning; properties it may be possible to impart them by adding to the hazardous substance a small quantity of a relatively harmless substance which has a high warning intensity.]

Jan 1, 1929

By Donald O. Capstick

[ ]

Jan 1, 1983

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By Ralph B. Stevens

The objective of the Automatic Fire Sensing and Suppression Systems for Mobile Mining Equipment program is to document the design, fabrication, factory testing, 11-month in-mine testing, and final demonstrations of auto¬matic fire protection systems on several units of mobile mining equipment including trucks, front-end loaders, cranes, draglines, coal haulers, and cutters. Proper sealing of all system components from the elements, especially in corrosive mine conditions, is essential for reasonable life-cycles with minimum maintenance. Also, adequate power supplies, wire, connectors, and plumbing with adequate protection from the harsh mine environments and physical damage were necessary during the in-mine tests. The fire protection systems were developed from technology employed during two previous Bureau of Mines contracts: HO122053, Improved Sensors and Fire Sensing Systems for Mining Equipment, and H0232059, Validation Testing of Truck Fire Protection Systems.

Jan 1, 1978

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By John T. Neubert

Between 1988 and 1990, the U.S. Bureau of Mines studied the mineral resources of San Juan National Forest to appraise and determine types and locations of deposits that could be mined economically now and in the foreseeable future. The study included a comprehensive field examination and literature search. Substantial amounts of lead, zinc, copper, gold, and silver have been mined from within the Forest in the La Plata, Rico, Silverton, and Dunton areas. At least one buried 200 million ton stockwork molybdenum deposit occurs in the Rico area. Similar size porphyry copper deposits occur at the surface and about 1,700 feet below the surface in the Bedrock Creek area of the La Plata district. Numerous smaller base-and precious-metal and uranium deposits have been prospected and mined throughout the Forest. Coal, oil, and gas have been or are currently being produced in the western and southern parts of the Forest. Carbon dioxide occurs in the western part of the Forest. Strategic elements occurring within the Forest include platinum, palladium, cadmium, gallium, indium, bismuth, and tellurium; however none of these elements is economically recoverable at present. Several geothermal areas are scattered across the eastern two-thirds of the Forest. Industrial minerals within the Forest include sand and gravel, limestone, and decorative stone.

Jan 1, 1992

By W. P. Yant, R. R. Sayers, H. W. Shoaf, John Chornyak

"The contemplated use of dichloro-difluoro methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for Public buildings and possibly homes, brings attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorine compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines was requested to make a laboratory study of the toxicity and potential hazard:"" and it was on the basis of the results of this work and the results of a preliminary investigation made in another laboratory5 that the compound has been selected for commercial use. Although the investigation conducted by the Bureau of Mines is still in progress, information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:Additionally work rich is in progress at the present time includes a determination of the lethal time-concentration curve for animals and a study of the response of persons within the range of safe concentrations.The writers desire to jive acknowledgment to T E. Midgley, Frigidaire Corporation, Layton, Ohio, for suggesting the investigation, for arranging for the cooperation of the Frigidaire Corporation, and for advice during the experimental work; to Robert A. Kehoe, The Eichberg Laboratory of Physiology, University of Cincinnati, Cincinnati, Ohio; and E. R. Hayhurst, college of Medicine, Ohio State University, for consultation and advice in planning the work; and to the following employees of the Bureau of Mines for assistance in performing the experimental work: L. M. Berger, chief scientific aid, S. J. Pearce, junior chemist, and Ethel B. Stead, technician."

May 1, 1930

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By R. J. Hundhausen

The Shamrock copper-nickel mine in Jackson County, Oreg., was formerly a part of the Chisholm mercury property. In 1948 new owners advanced the old workings 40 feet to reveal encouraging widths of copper-nickel sulfide, ore on the Shamrock claim. When the owner's funds became exhausted, the Bureau of Mines carried on the development in 1949-50, completing 1,650 feet of bulldozing trenching, 396 feet of drifting, and 3,419 feet of diamond drilling. The Bureau's trenching disclosed a separate surface deposit 600 feet south of the mine deposit. This and the previously known deposit subsequently were diamond-drilled. The underground deposit has a known length of 100 feet, a dip length of. 100 feet and a width varying from 1 to 25 feet. The surface deposit is 200 feet long, 200 feet deep, and 5 to 38 feet wide. Neither deposit has been entirely delimited by development to date.

Jan 1, 1952

By G. R. Hopkins

According to the annual refinery-capacity survey of the Bureau of Mines, the number of refineries in the United States showed little change in 1940, increasing from 057 the first of the year to 562 at the close. Although a number of plants were dismantled in Texas and other States, more than compensating gains were made in California, Illinois, and other States. Low gasoline prices, competition for crude-oil supplies, particularly in Illinois, and the termination of a favorable distributing arrangement for independent plants in the Los Angeles area, forced about 50 refineries to close down in 1940. The number of operating plants accordingly declined from 461 on January 1, 1940 to 420 on January 1, 1941 and the number of idle plants increased from 86 to 136 in the same period. These developments were also reflected in the capacity data, the operating capacity declining from 4,196,694 barrels daily on January 1, 1940 to 4,180,588 daily on January I, 1941 and the idle capacity rising from 431,952 barrels to 53g8381 barrels in the same period. However, the completed capacity on January 1, 1941 (4,718,969 barrels daily) was 2 percent above the previous year.

Jan 1, 1941