Search Documents

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By Robert W. Waytulonis

The mining regulations of all 50 States were reviewed by the Bureau of Mines, and those parts pertaining to the use of internal combustion (IC) engines (particularly diesel engines) in underground mines or confined spaces were extracted. Also extracted were subjects associated with the use of IC engines; for example, storage and handling of flammable liquids, maintenance, and ventilation requirements. As the laws now stand, 29 States have specific regulations that affect the operation of diesel engines in underground coal and/or metal and nonmetal mines. The other States have no regulations because either they have no mining activities or they defer to Federal regulations. Six states have regulations expressly prohibiting the use of diesels in underground coal mines. Specific contacts (addresses and phone numbers) precede each State's regulations to facilitate inquiries about regulation revisions and interpretation.

Jan 1, 1981

By C. G. Maier

The fundamental chemistry of zinc smelting, especially that part dealing with the chemical reduction of the zinc-oxide content of a roasted zinc ore, has been discussed by metallurgists in some detail, but, in the light of present knowledge, unsatisfactorily. A considerable portion of the information available has been qualitative, or quantitative in a sense that could not be interpreted chemically. A number of attempts to elucidate the physical chemistry of zinc oxide reduction have been based upon unsubstantiated and, as is now known, incorrect equilibrium data. To write upon the chemistry of zinc smelting at this time, when electrolytic methods for the production of zinc metal from ore are becoming increasingly widespread, may seem a belated effort. So, for example, C. A. Hansen,3 in the communicated discussion of an article by the author,4 writes as follows:

Jan 1, 1930

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By Edward L. McHugh

The study area, which comprises 28,443 acres within the Jacumba Wilderness Study Area, is in the California Desert Conservation Area, and along the U.S.-Mexico border 25 miles west of Fl Centro, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of mining claims, known mineral occurrences, and mineralized zones during the fall of 1983. Limestone resources were identified inside the study area; tungsten resources may he present. Metasedimentary rocks intruded by Cretaceous Quartz diorite predominate in the study area. Tungsten and some gold have been found in skarn zones along intrusive contacts; limestone deposits are in the pre-Cretaceous rocks. Tertiary and Quaternary volcanic flows, pyroclastic rocks, clay beds, and diatomite in lake deposits nave been investigated for possible non-metallic resources. Evidence of mining or prospecting was found at 26 sites in or just outside the study area. In 1983, 106 claims were held in 13 claim groups. One claimant was sporadically prospecting for gold on claims in the north part of the study area in 1983, and gravel was being mined from alluvium 1/4 mile to the east.

Jan 1, 1985

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940

By Alfred Petrick

This report analyzes the byproducts systems of lead, zinc, uranium, rare earths, iron, aluminum, titanium, and lithium. Specific byproduct metals covered are cadmium, germanium, indium, and thallium from the zinc system; antimony and bismuth from the lead system; vanadium, radium, and scandium from the uranium system; rare-earth oxides from the rare-earth system; and cobalt, gallium hafnium, and rubidium from other systems. The report discusses various metallurgical systems, marginal and incremental production costs of byproduct subsystems, industry structure and organization, and historical data on price, consumption, and supply.

Jan 1, 1973

By Albert L. Toenges, Theodore R. Jolley

"INTRODUCTION The construction of frame houses (fig. 1) in recent years instead of the conventional sod hut (igloo) (fig. 2) by the Eskimos in the villages along the Arctic Ocean has increased the demand for fuel in these villages. The frame houses, which are not insulated against extreme cold and are difficult to heat, are equipped with Goal stoves. The well-insulated sod huts were heated comfortably with whale-oil stoves. In some years whaling is Door, consequently there is a demand for solid fuel.The Eskimo villages usually are on the sand spits at the mouths of rivers and points of land near the best fishing and hunting grounds. These narrow necks of land usually are sand bars that are not underlain with coal, and coal must be transported to the villages. Lack of development of coal deposits in the Arctic has made it necessary to import coal from the States, generally from 'Washington, to supply these villages. This coal is imported by boat and is received once a year. Its cost is, high, and development of coal deposits in the Arctic to supply these native villages should result in a considerable saving to the Government-operated schools and hospitals as well as to the natives.Early traders attempted to establish coaling stations in the Arctic, and the Eskimos generally know where the coal deposits are situated. A. reconnaissance of a number of deposits in the Arctic was made in the summer of 1946 by engineers of the Coal Division, Fuels and Explosives Branch, Bureau of Mines, and this report describes the areas investigated and suggests plans for the development of some of these deposits."

Dec 1, 1947

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"FOREWORDFerrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade are in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory,and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the were discussed in the foreword of the first paper of this series, Report of Investigations 3606 Manganese Investigations. 1. Concentration of Manganese Ores,from the Drum Mountain District, Utah, by S. R. J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By R. R. Wells, G. M. Potter, A. O. Ipsen

This paper gives results of laboratory and pilot - plant investigations of concentration of western manganese ores during the Bureau of mines manganese-development program initiated in December 1940. The data summarize results obtained from laboratory investigation of concentration of ores from three properties in southeastern Arizona . The high - grade Gray - claims lot B ore , a product of hand sorting , is marketable directly or after sintering treatment . Intermediate - grade lot A selectively mined ore would be marketable after sintering as a plus 35 percent manganese produce , but gravity concentration methods were employed effectively to produce high - grade manganese concentrates with over 80 percent recoveries . Complex association of fine - grained manganese oxides , calcite , and fluorite in a siliceous ground mass limited the recovery of high-grade manganese concentrates obtainable from the low-grade Pyrolusite -group ore . A recovery of 63.7 percent of the manganese was made by flotation in a concentrate that sintered to plus 48 percent manganese grade . The low-grade Davis ore contains iron and manganese oxides too intimately associated to permit production of marketable manganese products . However , good rejection of calcite gangue was obtained by flotation , and the enriched manganese - iron product might have value as a spiegeleisen ore .

Feb 1, 1946

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

By Charles B. Carpenter

The New Hope field was selected for study by; Bureau of lanes engineers because many problems met by, the operators during development and operation were unique to petroleum-engineering experience. Solving these problems is believed to have doubled the ultimate recovery of oil from the field. Since the discovery well was 'completed, in April 1943, an oil-productive area of 4,950 acres- has been delineated by the drilling of 64 wells, four of which were dry holes. Four oil-bearing reservoirs - the Bacon oolitic limestone, and the Hill, Pittsburg) and Elledge sandstones, all, in the Trinity group of the Lower Cretaceous series-- have been penetrated at depths ranging from 7,300 to 8,100 feet. Three of these reservoirs were found to be closed-type or solution gas-drive reservoirs, and one - the Hill - was an open-type or water-drive reservoir. During the course of the study, the Tide Water Associated, Oil Co. and -Seaboard al Co. of Delaware made available to the writers all well records, electric logs; and coring, production,, and pressure data. The ,writers performed Certain field and laboratory- tests on cores of ,the reservoir racks and' samples -of the reservoir Oils. Analyses of cores from the four reservoirs showed average .porosities ranging from 10 to 18 percent, average permeabilities of 17 to 297 millidarcys, and -average 'connate water contents ranging from 25.4 to 30.6 percent. Subsurface and recombined samples of reservoir oils indicated that the oils in the Bacon Hill, and Pittsburg reservoirs contained ,206 to 422 cubic feet of gas in solution per barrel initially, and that the, reservoir oils were undersaturated with gas. No samples' of oil from the Elledge reservoir were analyzed, and because of meager data this reservoir was not studied in detail. 4 The presence of free 'gas' or a' gas cap, however, indicated that the oil in the Elledge reservoir was saturated with gas. The rapid decline in pressures in- the' four reservoirs during the 'first year of operation alarmed the operators and provoked them to investigate the reservoir conditions to determine the cause.

Jan 1, 1949

By V. B. Royer, C. H. Harty

"MANGANESE-SILOCON ALLOYS AS DEOXIDIZERSThe basic open-hearth process for steel mining requires large amounts of oxidized iron for oxidation of the elements carbon, silicon, manganese, and phosphorus which are to be removed from the metal. Some of this oxidized iron (FeO) dissolves in the metal during the refining process, Subsequent to the elimination of the elements named, a considerable amount of dissolved iron oxide must be removed before the metal may be cast into ingot form. The elements generally used, for iron oxide removal, or deoxidation, are silicon, manganese, and aluminum. Silicon and manganese are always alloyed with iron, either singly or in combinations of various compositions. Aluminum generally is used in a commercially pure state and sometimes in complex alloys. A double deoxidizer of manganese and silicon alloyed with iron for furnace deoxidation has been the subject of an extensive cooperative investigation between the United States Bureau of Mines, the Carnegie Institute of Technology, and the Metallurgical Advisory Board. Certain grader of steel, especially low-carbon rimming steels, require a low-carbon deoxidizer to keep the finished steel within the carbon specification after deoxidation. ACKNOWLEDGMENTThe authors wish to acknowledge the assistance of J. F. Sanderson and S. S. Johnston in the analysis of the alloys used in this work.PURPOSE OF WORKThe need for definite information as to which compositions of manganese and silicon within a certain manganese-silicon ratio and when alloyed with iron would have an allowable carbon content for the particular grade or type of steel on which the deoxidize is used, prompted the undertaking of this investigation to determine the solubility of carbon in manganese, silicon, and iron alloys within the region bounded by 10:1 and 4:l manganese to silicon ratios. These data should be of value to the manufacturer producing such"

May 1, 1934

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By Kenneth H. Johnston

This report describes an in situ combustion project and three waterflood projects in Allen, Anderson, and Wilson Counties, Kansas, that will be visited during the 1964 annual tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the movement of heavy crude oil through the reservoir and into the wellbore with energy furnished by burning a portion of the crude oil therein. Another feature is the simultaneous injection of C02 and water, through separate tubing into input wells during early development, to increase injectivity at moderate pressures, Discussion of individual projects includes information on their early history, source and treatment of injection fluids, oil production-decline curves, and the results of water injection on oil production.

Jan 1, 1964