Search Documents

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Adrian Moore, Dominic Hooton, Alan Richards

Significant factors affecting airblast overpressure (AOP) emissions include charge mass per delay, distance from the blast site, burden, stemming height, and delay timing, topographic shielding, and meteorology. The effect of charge mass on the frequency of the airblast produced, and the delay timing required to control the level of airblast overpressure is explained by two case history examples which were not affected by topographical shielding and meteorology. One is a cast blast with a charge mass per hole of 1000 kg (2200 lb), and the other is a quarry blast with a charge mass per hole of 64 kg (141 lb), These examples show that the delay interval necessary to prevent an increase in AOP levels must be increased with an increase in charge mass per hole. The effect of a ‘soft-start’ technique where a reduction in AOP levels is achieved by decking only the initial front-row holes is also illustrated.

Jan 21, 2025

By Luis Huaroc, Jorge Cardenas, José Salvador

One of the current challenges in mining is managing increasingly competent rock conditions within the mine-to-plant value chain, particularly when working with marginal ore grades. This study presents a case from a Peruvian open-pit operation where the mine plan projected a significant increase in rock hardness, as measured by the Axb index (parameters derived from the JK drop weight test). In response, the Drill and Blast Technical Team made efforts to increase the powder factor by reducing drill spacing and increasing the explosive charge, employing high-energy explosives (3,090 kJ/kg). However, this adjustment presented a challenge in achieving the fragmentation required to meet the target throughput of 97,500 tons/day, resulting in a shortfall of approximately 8.7% under the base case scenario. To overcome this technical challenge, the use of locally engineered ultra high-energy explosives was proposed, offering adjustable energy levels ranging from 3,210 to 3,570 kJ/kg. This solution enhanced ore blending strategies, calibrated to specific Axb ranges. The results also suggest that microfractures generated by the energetic blasting designs contributed significantly to downstream improvements. These outcomes demonstrate the value of a fully integrated mine-to-plant strategy, aligning blasting parameters with downstream processing performance to maximize operational efficiency. This solution led to a 10% increase in process plant efficiency, a 16% reduction in specific energy consumption during primary crushing, and a 13% reduction in the SAG mill. Additionally, shovel productivity rose by 18%, and the dig rate improved by up to 35%. Keywords: fragmentation, blending, high-energy explosive, power factor, microfractures, specific energy consumption and Axb model.

Jan 26, 2026

By C. Heiss, A. Hofmann

Due to an explosion in an Austrian steel works during the basic oxygen process, the Chair of Mining Engineering and Mineral Economics at the Montanuniversitaet Leoben was assigned with the set-up of a test arrangement to study the effects of large-scale particle emissions on the plant´s installations and the testing of various structures and structure-combinations to be applied as explosive-proof enclosure.

Jan 1, 2012

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By Dominic C, Gregory B. Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction

Feb 1, 2020

By K. Best, D. Conn

The US Army Corps of Engineers KY Lock Project in western Kentucky presented the blasters and vibration consultants with a set of unique challenges. The blasters on this project were faced with difficult geology and joint set orientation and sequencing of blasts opposite from what the explosive engineer/blasting specialist had recommended. Combining these issues with strict vibration and air overpressure specifications, blasting as close as 7 feet (2.1 meters) from a new lock wall, site topography that influenced the air overpressure, limitations on seismograph geophone placement that led to anomalies in seismograph recordings; surprising lessons were learned by everyone involved in the project and it is the authors’ goal to share this valuable information with everyone in the blasting industry.

Jan 1, 2024

By Jorge Cárdenas, Diego Gamarra

In previous phases of the mine, a landslide resulted in several losses in production delays. The stability of slopes in a mining operation is critical for the sustainability of the operation, as they are exposed to vibrations and damage caused by blasting. Therefore, it is essential to implement controls and innovative technologies to reduce these vibrations levels. This study focuses on the application of low-energy emulsions with lower densities than conventional explosives, developed to reduce vibrations and the energy delivered to the rock mass adjacent to the near blast holes as a buffer row. Near field studies were carried out by embedding triaxial geophones. Vibrations were recorded, and mathematical models of vibration associated with different types of explosive mixtures were generated. This allowed us to determine the benefit of implementing low-density explosives in reducing vibrations compared to Heavy ANFO explosives. The application of low-energy explosives with densities ranging from 0.7 to 0.8 g/cm³ and Relative Bulk Strength (RBS) of 51-65 allows for a 40% reduction in vibrations compared to the detonation of Heavy ANFO explosives.

Jan 21, 2025

By Braden Lusk

The problem of predicting damage in densely developed areas due to incidental or malicious explosions is one of considerable importance to local, state, and federal governmental bodies. The difficulty of making such a prediction is confounded by the urban canyon phenomenon as the shock wave intensifies or rarefies depending upon the particular arrangement of buildings. The specific method detailed herein used a Computational Fluid Dynamics solver, ANSYS AUTODYN, to operate on Geographic Information Systems data, ArcGIS, which captured the geospatial relationship between the various buildings in downtown Oklahoma City, prior to the Murrah Building bombing. The model of Oklahoma City was first developed using the building footprints and elevations provided by the ArcGIS database. Due to the sheer size of the problem, the model was then subdivided into annular zones of increasing distance from the center of the blast. Each subsection was then solved using an Euler model in a cascading fashion with the output of the preceding model forming the input of the present model. To further reduce computational time, the size of the Euler nodes was increased at each stage as the section area increased. Due to the loss of precision in capturing peak pressure values when using larger size nodes, it was necessary to perform a transformation on the results using one dimensional wedge calculations with higher precision. The Murrah Building bombing event was an excellent case study due to its available ArcGIS data and the level of documentation of damage to surrounding structures due to the blast. The results from the staged CFD calculation were then used to develop a damage potential contour map. The documented incidents of damage in the area surrounding the Murrah building were then compared to the model generated damage potential contour map. Copyright ©

Jan 1, 2010

Over 45 of the Best Qualified Technical Specialists, Consultants, Engineers, Scientists, Explosive Supplies, Educators and Mine Operators in the World!

Jan 1, 2000

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Robert Hopler

A detonator is a copper tube about a quarter of an inch in diameter and an inch and a half long, closed at one end and containing in the closed end a small charge of fulminate of mercury, which has been found to be the best explosive for detonating dynamite. The fulminate charge is a very powerful explosive very sensitive to friction, lows or heat and very poisonous. When exploded it has an intense local action, shattering things in its immediate vicinity, but not extending very far away from the explosion. This kind of detonator is intended to be exploded by a spark from burning fuse.

Jan 1, 2014

By David Leidel

A revolution in hydrocarbon well completions within the last thirty years has enabled drillers to tap the resources of known gas plays in an economically viable manner and deliver to market natural gas supplies for industrial, transportation and domestic use without the importation of liquefied natural gas from verseas. An added benefit has been the convenient location of one of these gas plays, the Marcellus Shale, in the Northeastern states strategically close to a major natural gas market, namely the cities and towns of the New England and Mid-Atlantic states. As a sidelight, the development of the tight gas reservoirs and their subsequent production has created thousands of jobs in an otherwise lackluster economy.

Jan 1, 2014

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By R. Ticona, J. Alarcon

In the continuous search to provide comprehensive solutions and identify opportunities to improve ore traceability, from the blastholes to mill feed, different ore traceability systems have been developed, which allow tracking the ore and associating its geometallurgical characterization of different sectors of interest from blasting to the processing plant, facilitating decision making and operational actions when detected during each stage of the plant. With the objective of improving the ore tracking from the mine to the processing plant in a Peruvian copper mine operation, the impact on the processing plant was evaluated in relation to blasting optimizations through a tracker system, relating the processes performance of the whole production chain with the geotechnical and geometallurgical properties ores in real time in the process plant: detecting when it was feed waste, high grade ore, low grade ore and ore with arsenic, among others. Unit and integral tests were carried out over a period of three months, with an implementation of tracker detection portals in the processing plant, which allowed to verify the proper communication of data and the web platform. The tests were focused on several blasts where the ore was in contact with waste and it were directly sent to the plant, with a classification by type of grade (high, medium, and low grade), type of material (ore-waste contour), this stage allowed to make operational adjustments in the field and in the mining operation. Finally, in the economic results, the special tests had 1000 trackers, obtaining for this project a sensitization of a cost benefit for the test stage, for the reduction of 50% of the waste material feed has crushed, with an estimated benefit of 1,987,646 USD.

Jan 1, 2024

By Mark Bosse

This is a paper demonstrating the use of a fixed wire and trolley system to deliver 2 or 5 lb cast primers (with 2 meter cap/fuse assemblies) deep into avalanche terrain. This avalanche terrain is mitigated using explosives prior to being opened to guests.

Feb 1, 2020