Search Documents

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By Orica Peru, Pedro Lozada

Proper management of exclusion zones in blasting operations is essential to ensure safety without compromising operational efficiency. In Peru, mining regulations establish minimum exclusion distances specifically for personnel (500-meter radius / 1,640 feet), but do not define clear technical criteria for equipment. As a result, conservative distances such as 200 meters (656 feet) are often applied, negatively impacting productivity. This study proposes a technical-scientific methodology to reduce equipment exclusion zones, based on the use of advanced technologies such as drones, high-resolution cameras, and specialized software tools. The solutions used allow video recordings of blasts to be transformed into dynamic data through artificial intelligence and computer vision, as well as execute probabilistic simulations of the flyrock phenomenon using Monte Carlo algorithms and physical models calibrated to real operating conditions. Technological integration enabled the simulation of real operational scenarios, considering variations in critical blasting parameters that directly affect flyrock generation, such as drill diameter, explosive density, linear charge, and stemming height. Additionally, the Terrock methodology was incorporated, allowing the behavior of the rock mass to be included as a variable in risk assessment, improving analysis accuracy under different rock hardness conditions. The methodology was applied in four phases: diagnosis of the current design (15 blasts), modeling, validation of the calibrated model (6 blasts), and subsequent operational implementation. As a result, it was determined that the exclusion radius can be safely reduced from 656 to 492 feet (200 to 150 meters), maintaining as the main restriction the use of stemming lengths greater than 5.0 m. This optimization has the potential to generate tangible benefits, with estimated monthly savings exceeding USD 50,000, associated with reduced evacuation times, lower fuel consumption, less equipment wear, and increased productivity in drilling and hauling activities. The comprehensive approach presented here highlights the transformative potential of digital technologies applied to blast management, contributing to safer and more efficient mining operations.

Jan 26, 2026

By Gregory Hempen, Thomas Keevin, Russell Wilcox, William Wild

The Department of Defense Strategic Environmental Research & Development Program (SERDP) awarded funding for evaluation of procedures to mitigate peak pressures and energy flux density in the water column from ordnance being detonated on the ocean floor. The research purpose was to conduct scaled testing to resolve whether a theoretically-viable covering technology was operationally effective in reducing blast effects and the impacts of shrapnel. An additional objective was testing effectiveness of this method for hard-bottom units (rock or coral) and (unconsolidated) sediment substrate.

Jan 1, 2011

By S. Geerts, J Davidson

The purpose of the experiment was to determine detonation characteristics of various improvised explosives. The test consisted of detonating a pipe filled with an explosive compound inside of a plywood arena. The pipe will be located in the center of the arena to ensure even distribution on the witness panels. Details on pipe dimensions, weights of the pipe and explosive, and the density were recorded prior to testing for use in the model calculations. The same size pipes were used throughout to minimize the variables inherent in testing. The plywood witness panels will capture the fragments so that penetration data was obtained, primarily the surface area of impact and depth of penetration. Through the use of the penetration data in conjunction with a mathematical model the original fragment velocity was determined. The mathematical model was developed to measure lethality of fragments from explosives and was modified to determine the original fragment velocity instead. From this model other variables such as the Gurney velocity were calculated. This test was done with an explosive compound that was commonly found, and numerous improvised compounds. In order to guarantee accurate data all of the explosives used for testing were cap sensitive, to eliminate the need for a booster charge which would introduce many unknown variables. The one common explosive compound that was used was C-4 which has known data in order to show accuracy of the model and calculations. The other 5 compounds chosen will not have this data as they will primarily be improvised mixtures.

Jan 1, 2011

By Lon Santis, Bill Evans, John Tatom

Debris data from the Department of Defense Explosives Safety Board’s Project ESKIMORE full-scale explosives event test program are compared to quantity-distance (Q/D) standards and quantitative risk analysis (QRA) methods. The ESKIMORE test program involved quantities of explosives ranging from 1,000 to 60,000 pounds detonated in typically sized structures made of metal and concrete. Debris from these events was extensively surveyed and catalogued. The debris patterns from these events show varying degrees of directionality normal to the walls of the structures. These density patterns are overlaid an existing explosives storage site that is comparable to the test conditions. Analysis of the debris patterns in relation to Q/D standards shows that exposures located beyond the Q/D arc but along the normal to walls of potential explosion sites (PES) may have much higher debris density than exposures at the same distance on the corners of the same PES. Analysis of the debris patterns shows that predicted patterns using the QRA tool IMESAFR v2.0 closely match actual patterns. Additionally, IMESAFR based QRA methods are able to quantify the different risk levels of being exposed along the wall’s normal as compared to being exposed on the structure’s corner. Methods and decision making criteria to mitigate risk based on the directionality of PES debris are presented. Copyright ©

Jan 1, 2015

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By Alan Hooper, James E. Mischler

Construction began in 1984 for a 5 megawatt hydroelectric power retrofit at the O'Shaughnessy Dam for the City of Columbus, Ohio. The construction necessitated excavation of limestone bedrock up to 27 feet below the normal water level of the river downstream of the dam. Proximity to the river and difficult terrain resulted in an interesting and challenging construction project.

Jan 1, 1986

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By Raúl Carretero de la Hoz, Leonardo Soares Chaves, João Paulo Soares Toneli, Francisco Felipe da Silva Dantas, Marcos Peres Lopes, Marcus Vinicius da Silva Gonçalves

The mining activity results in environmental impact and thus requires the adoption of techniques to minimize its effects. The rock blasting process is required to break up and move the rock enabling the haulage of the material, however, it might also cause undesirable effects such as flyrock, overbreak, excessive ground vibration or air-blast at the neighboring communities and damage to civil or geological structures located nearby. The Serra Sul mine, commonly referred to as S11D project, has obligations to preserve two natural tropical montane lakes and several maximum relevance natural cavities whose legal preservation radius represents constraints to the mine development and operation. Controlling measures are undertaken to ensure preservation of the cavities, especially during rock blasting stage, with limitations of the maximum instantaneous charge (MIC) and ground vibration control. The demand for high productivity and the large areas with hundreds of blastholes to charge are challenging factors to the charge control. This work presents the development and field application of a map for limiting explosive charges in the rock blasting process at the Serra Sul mine, used for the definition of maximum charges according to the blast location, ensuring the preservation and compliance with the defined ground vibration limits for each cavity. The map is applied at the mine for every blast and when there is a charge constraint, the map helps to define the areas with different charging profiles in the field contributing to higher charging productivity.

Jan 21, 2025

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By Alyse Munro Hindley

The increasing negative public opinion toward blasting has led to stricter regulations and increased costs. This paper outlines alternative methods of rock excavation and the safety regulations and certification required by blasting professionals. Most importantly, however, it showcases the benefits and accomplishments that controlled blasting bring to society, giving the public a better understanding of the necessity of blasting in modern society.

Jan 1, 2015

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Khiva Haidar Shauma Tassno, Zulham Ahmad, Farhan Harist Maharesi, Abdullah Badawi Batubara

Blasting operations can use a bulk emulsion explosive (EE) with a formulation based on used oil as a replacement for refined fuel oil. The most commonly employed used oil for making EE is a mineral based used engine oil that passes an impurity content standard. It is known that not all types of used oil are easily incorporated into EE formulations. Impurities in used oil can disturb EE stability resulting in crystallization and phase separation and consequently led to poor detonation quality. In 2024, a poor blast result occurred at an Indonesian mine due to utilization of used oil that was not within specification. A research project conducted from February to April 2025 found that used transmission oil differs from used engine oil in hydrocarbon composition. Transmission oil contains more additives that affect EE stability due to polarity differences and the disruption of colloidal state stability. Lab tests including stress testing and crystal growth observation aided the development of a stable EE formulation based on used oil and used transmission oil. In mid-April 2025, blast evaluations were conducted using the EE that was formulated using used engine oil and used transmission oil. Measurements of velocity of detonation, fragmentation, and digging time, demonstrated high quality EE was produced. Application of used oil in EE revolutionized the capability of mining operations to improve blast sustainability and cleanliness. Through comprehensive research, robust testing, and effective supply chain management, it is possible to replace some portion of refined fuel oil with used oil without compromising blasting performance. The inclusion of used transmission oil broadens the overall used oil specification and increases the volume of recycled used oil available for blasting. The increased volume of used oil available can reduce the amount of waste generated by mining projects while maintaining operational efficiency.

Jan 26, 2026

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026