Search Documents

By Groom P.

The wastage of timber in coal-mines that is caused by decay is very great; in fact, far greater in this country than is generally realized. Mr. E. W. Peters estimates that of the whole wastage of timber in mines in the United States of America, 50 per cent, is due to decay and insects; of this 50 per cent, an overwhelming part is due to decay. The most efficient methods of decreasing this grave loss can be devised only by co-operation of the mining engineer and the scientific expert, and it is partly in the hope of procuring such collaboration that this paper is written. It contains, therefore, a resume of our present knowledge of the decay of wood, and of the economic methods of checking this in mines; but, with a view to improving those methods, it also directs attention to the gaps in our knowledge and the means by which these can be filled by future investigation

Dec 1, 1916

By C. A. Pickles, S. J. Splinter, J. Cameron

The addition of copper oxide to a borosilicate slag resulted in the breakdown of the silicate network and a dramatic decrease in viscosity. With increasing borax to silica ratio the viscosity was reduced by two mechanisms. First, rising sodium oxide content promoted cleavage of the Si-O bonds. Second, increasing boric oxide (B2O3) content increased the number of trigonal borate units that were converted to tetrahedral borate units by sodium oxide and copper oxide. The BO4(4-) tetrahedra decreased the local silicate symmetry, thus disrupting the silicate network and lowering the viscosity. The activation energy decreased with increasing temperature and increasing copper oxide content

Jun 13, 1905

By Winmill T. F.

(Paper presented at the Institution of Mining Engineers' general meeting held in London on 8th June 1916.) The conclusions reached in this paper may be summarized briefly as follows: (1) The method of estimating moisture in coal by determining the loss in weight of a sample heated to 105°-110° Cent, in an air-bath for an hour is untrustworthy, the results so obtained being too low. (2) Dried coal has a very considerable power of absorbing moisture, and a sample, after being dried, must be protected instantly if it is to remain free from moisture. (3) A fairly accurate estimation may be made by heating the coal in a current of dry air at 105° to 110° Cent., and collecting the moisture evolved. (4) In cases in which it is proposed to use the dried coal for any further experiments, the drying must be done in the absence of oxygen, and this can be done simply and quickly by the vacuum method now described

Dec 1, 1916

By M. W. Davies, P. N. Smith

The activity of MnO has been measured in the system CaF2-MnO at 1773 and 1873 K and in the system CaF2-CaO-MnO at 1773 K by the method of equilibration with platinum. Large positive deviations from ideal solution laws have been found, but these became less as the lime content rose. The loss of a volatile component made activity measurements impossible in the CaF2-AI203-MnO system, but the boundaries of a two-liquid region have been measured at 1773 K.

Dec 1, 1971

By Eric Forssberg, Vigen Zeng

During mechanical grinding high intensity vibration is emitted that contains information on the mill's operating state. Tests, using a laboratory ball mill, studied the influence of operating parameters on the vibration signature. The parameters studied were: mill speed; powder filling; pulp density; grinding period; and pulp temperature. Vibration signals were detected by an accelerometer, amplified by a vibrometer and recorded onto digital audio tape. A digital oscilloscope converted the signals into IBM-compatible data format. Digital signal processing and multivariate data analysis were carried out with specially developed software. The power spectral density was estimated from the time-domain vibration signal. Four new latent variables were used to describe changes in the vibration spectra. A relationship was established between operating parameters and latent variables which could form the basis of a quick and automatic method of monitoring operating parameters in ball mill grinding.

Jan 4, 1993

By S a m u e l D e a n

The author's written response to previous discussion was presented at the North of England Institute of Mining and Mechanical Engineers general meeting held in Newcastle-upon-Tyne, 8 April 1916, followed by further comments by Hare S. in support of his view that the conditions in English mines were the reason for less satisfactory results being obtained with heading machines and brief comments by Greener T.Y., President

Dec 1, 1916

Summary of the morning's events with a Written Contribution to Paper No. 4 and author responses

Jan 1, 1947

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By J. Laskowski, J. Lekki

"The mechanism of joint action of a frother (alpha-terpineol) and a collector (ethyl xanthate) in the flotation of chalcocite has been examined. In order to study the dynamic effects of frother and collector in bubble-particle collisions, the following aspects were investigated : determination of zeta-potential. Measurements of the thickness of fluid film on the surface of chalcocite and adsorption of xanthate, as influenced by alpha-terpineol, induction time and flotation versus concentration of alpha-terpineol and ethyl xanthate.The mechanism of the adsorption-desorption phenomenon on chalcocite with regard to non-ionic molecules, e.g. a-terpineol, has been considered, and the influence of this on the stage and thickness of the intervening wet layer between a bubble and a particle, changing the probability of collision and attachment, is suggested."

Dec 1, 1971

By N. T. Moxon, D. Mead, S. B. Richardson

A laboratory and theoretical study of air decks was carried out to assess the effects of the size and location of air-decks on fragmentation. The degree of fragmentation was found to depend on both factors. As the size of the air-deck increases the degree of fragmentation is reduced relative to a full column charge. However, the reduction is relatively small until a critical size is exceeded. The critical size depends on the strength and structure of the surrounding material. A critical air-deck length of 30-35% of the original explosive column was determined for the model materials used in the study. A theoretical explanation of the results was derived based on pressure decay rate relationships. The location of the air-deck also influences fragmentation. The interaction and oscillation of the two shock fronts from the top and bottom charges mean that mid-column air-decks produce better fragmentation for the same air-deck length and explosive loading as top-column or bottom-column air-decks.

Jan 4, 1993

Jan 1, 1947

By H. L. Shergold, O. Mellgren

The conditions of amine concentration and pH necessary for the concentration of fine haematite particles at the iso-octane-water interface have been determined. Results obtained from the related studies on the effect of pH and dodecylamine concentration on the adsorption density, electrokinetic potential, contact angle and concentration of various amine species in the system are included. A good correlation was obtained between these different variables. Maximum concentration of haematite at the oil-water interface was obtained when the haematite zeta-potential was small or equal to zero

Dec 1, 1971

By J. E. Rouse, D. L. Buchanan

"During the emplacement of the Bushveld Complex in the Potgietersrus area magma reacted with the original floor rocks— Archaean granite or Malmani dolomite and overlying Penge handed ironstone or sedimentary rocks of the Pretoria Series. The complex sequence of sulphide-rich mafic rocks that formed along the contact is known as the Platreef. Associated with the sul­ phide mineralization are important concentrations of platinum-group metals, copper and nickel. Xenoliths of Malmani dolo­ mite have been incorporated into the Platreef and previous work has suggested that anhydrite is likely to have been present in the dolomite. The sedimentarv-derived sulphur thus introduced into the magma exercised an important control on the forma­ tion of the sulphides.Petrographic studies on the Platreef rocks from the Tweefontein area indicate that the original magma reacted with the banded ironstone to form iron-rich pyroxenites. In the Turfspruit area, to the south, the footwall rocks consist of sediments of the Timeball Hill Series. Original argillaceous rocks have been metamorphosed to cordierite-, corundum- and spinel-bearing hornfelses. Graphite was present in the contact zone in both the Tweefontein and Turfspruit areas. Anhydrite-bearing hornfels rocks are also present on Turfspruit.The Platreef rocks that overlie the corundum- and spinel-bearing hornfelses on Turfspruit are peridotitie, and pyroxenites are present in areas underlain by cordierite-bearing hornfels. The absence of orthopyroxene in the peridotite is probably indicative of low silica activity in the original magma. The pyroxenites have, however, undergone silica contamination from the underlying more siliceous cordierite hornfels.Carbon isotope studies indicate that the graphite in the Tweefontein and Turfspruit samples represents organic material orig­ inally associated with the footwall sediments. Sulphur isotope determinations on the anhydrite-bearing floor rocks indicate that this phase is clearly of sedimentary origin and was probably derived from an evaporitic unit within the carbonate sequence. This provides firm support for a model of ore genesis that involved the introduction of additional sulphur into the Bushveld magma. Isotope studies on sulphides associated with the banded ironstone and graphite indicate that these units were not the source of additional sulphur. Experimental studies predict, however, that a magma contaminated with iron- and carbon-rich material would have a high sulphur-carrying capacity. Where additional sulphur is available the magma would achieve saturation early in its crystallization history and precipitate an immiscible sulphide phase. Experimental work has also shown that sulphide precipi­ tation can be triggered by the introduction of salic material into a magma close to sulphur saturation. This mechanism probably played a role in the control of the sulphide mineralization in the Turfspruit area."

Jan 1, 1984

By G Williams

Discussing equipment, systems of work, the need for updated programmes of local seismic exploration, and developments within the South Wales coalfield.

Jan 1, 1993

By F. Reich, S. L. Chryssoulis, K. G. Stowe

The surface chemistry of particulates from mineral processing streams can be determined by laser-probe microanalysis. The small area of analysis (2-30 micrometres) enables the surfaces of individual grains to be characterised. Conclusions are based on data acquired from a statistically significant number of grains of a given type. Maps showing the distribution of elements on the surface of mineral particulates can be obtained by time-of-flight secondary ion mass spectrometry. The importance of such analyses in understanding the response of minerals to beneficiation practices is discussed with reference to three examples. The first relates to the loss of selectivity in the differential flotation of a base-metal ore, the second to the different flotabilities of coarse- and fine-grained pentlandite from a Cu-Ni ore and the third concerns the preg-robbing effects of organic matter in a carbonaceous gold ore.

Jan 4, 1992

By D. J. Esdale, D. F. Pridmore, F. W. Lindman, J. H. Coggon

Almost all the presently viable nickel reserves in the Yilgarn Block contain nickel in a sulphide phase. Both volcanic peridotite- associated (VPA) deposits and intrusive dunite-associated (IDA) deposits are characterized by massive, matrix and disseminated sulphides (typically, pyrrhotite, pentlandite, pyrite, chalcopyrite, magnetite and other spinels), though in the IDA deposits the volume of disseminated sulphides is far greater than that in the VPA deposits. Potentially all geophysical techniques have application in the direct detection of these deposits'gravity for the detection of the dense massive and matrix ore; magnetics for the detection of magnetite and pyrrhotite in the ores; electromagnetics for the detection of the massive and matrix ore; and induced polarization for the detection of disseminated and to some extent matrix and massive ore. In practice the application of geophysical techniques is limited to a varying extent by (1) the relatively small size of an economic accumulation of sulphides, particularly the VPA deposits, (2) the extreme depth of weathering and lack of outcrop on the Yilgarn Block and (3) the abundance of geological noise or anomalous responses caused by sources other than economic mineralization.

Jan 1, 1984

The Council of the Institution of Mining and Metallurgy submitted the report of the affairs of the Institution for the session 1970-71, and the Statement of Accounts for the year ended 31 December, 1970. The statistics given in the report refer to the calendar year 1970. Details are included of membership, officers, representation on other bodies, honours and distinctions, awards, meetings, publications, library, overseas activities, fellowships and grants, the revenue and expenditure account, the balance sheet, trust fund balances, contributing companies, and schedule of investments

Dec 1, 1971

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By T. Piirainen, T. Alapieti

"The Koillismaa layered igneous complex is the result of igneous activity that occurred 2436±5 m.y. ago. Its crystallization took place in three separate but connected magma chambers, the total volume of which is estimated at more than 2000 km'. These chambers were located partly in a feeder system within Archaean granitoids and partly in an unconformity between these grani­ toids and Early Proterozoic supracrustal rocks. The composition of the parental magma that initially filled the chambers is thought to have been that of a relatively MgO-rich tholeiite. Sulphides and platinum-group minerals are mainly concentrated in the marginal series of the western part, where they are encountered over a distance of 25 km. This marginal series is an originally nearly horizontal series of rock types that displays a reversed differentiation trend, grading inwards from gabbroic to ultramafic rocks, followed bv rocks of the layered series. The chilled margin is not encountered anywhere in its original position at the contact, probably as a consequence of magmatic erosion, but remnants are to be found in the form of elongated xenoliths. Partly melted siliceous fragments from gneissic country rock typical of the lower part of the marginal series indicate pronounced contamination.Chalcopyrite, pentlandite and pyrrhotite±pyrite are the predominant sulphides. The accessory sulphide minerals include covellite, violarite, marcasite, mackinawite, sphalerite and argentian pentlandite. Platinum-group minerals are represented by froodite, michenerite, merenskyite and sperrylite. Other accessories that have been identified are electrum and native copper and gold. The mean of the Cu/(Cu+Ni) ratio in the mineralizations is 0.67 and Pt/(Pt+Pd) 0.31.It is suggested that the sulphide phase was formed in the marginal series as the solubility of sulphur in the basic magma was lowered by contamination, possibly assisted by some other factors. The sulphur isotope data support the juvenile origin of the sulphur."

Jan 1, 1984