Search Documents

By Shibayama A.

In this research, an investigation of a process to selectively remove arsenic (As) and antimony (Sb) contained in enargite (Cu3AsS4) and tennantite/tetrahedrite ((Cu1,Fe)12(As,Sb)4S13) copper resources by leaching and precipitation were performed. First in the leaching process, the target was to selectively leach As/Sb and reduce their contents in the ores to <0.5 wt% followed by a second process to remove As/Sb dissolved in solution for environmental control. Enargite ore contained 3.65 wt% As while tennantite/tetrahedrite ore contained 5.40 wt% As and 4.85 wt% Sb. Alkaline leaching using NaHS?NaOH media at varying experimental conditions (temperature, pulp density, time, reagent concentrations) were performed to investigate the process. As/Sb precipitation studies were also performed to control high As/Sb concentrations in leach solutions by using elemental sulphur (So). Results from leaching studies showed that over 99% of As/Sb in the impure copper ores can be removed and their contents in the final solids reduced to <0.5 wt%. It was also established that such very high leaching could be achieved at 80°C within 1?6 h and pulp densities as high as 1000 g/L. The study also revealed that leach solution containing very high As/Sb concentration ranging from 5 to 20 g/L can be used as fresh solution for leaching of fresh ores until concentrations exceeding 35 g/L when it was sent to precipitation circuit for As/Sb removal. Addition of elemental sulphur at 90°C and fast cooling to 30°C allowed over 60% As/Sb precipitation and removed as Na3AsS4 and solution with reduced As/Sb concentration to leaching circuit for continuous use. Keywords: Enargite; Tennantite/Tetrahedrite; Selective Leaching; Precipitation; Sodium hydrosulfide;

Sep 1, 2012

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

"The global demand for the copper metal is continuously increasing however, the high-grade copper ore deposits are constantly depleting. As a result, ore bodies with complex mineralogy characteristics and rich in arsenic-copper bearing minerals are increasingly processed. Arsenic-copper sulphides such as enargite can represent a significant amount of arsenic in concentrate, which causes high financial penalties by smelters. On the other hand, arsenic (As) is a highly toxic inorganic pollutant, which causes human health and environmental problems. Recent research studies have demonstrated promising results showing the possibility of separating arsenic-copper sulphides from copper sulphides using controlled pulp potential (Eh) flotation at laboratory scale. However, the selective removal of arsenic-copper minerals in real ore systems is not well understood. Two ore samples were selected from the Tampakan copper-gold deposit located in the Philippines named the HAS (high arsenic sample) and the LAS (low arsenic sample) samples and the mineralogical analyses were performed on both samples. The floatability of enargite in a batch flotation system under controlled pulp potential conditions was investigated for the HAS and the LAS samples. It was observed that it is possible to selectively separate enargite from other copper minerals after reducing the pulp potential to about -200 mV SHE at pH 11 in the LAS sample. However, no separation between enargite and other copper minerals was observed at a reducing potential for the HAS sample. Mineralogical analyses and surface chemistry studies were undertaken for both samples to find out the reasons for different observations. This study has an important implication in sulphide flotation to achieve sustainable development in the utilisation of arsenic-copper mineral resources. INTRODUCTIONAs the demand for copper is increasing, the extraction and development of resources including complex deposits is becoming necessary. These complex deposits often have issues such as: lower grade ores, floatable non-sulphide gangue, very fine-grained ore and therefore poor liberation and significant regrinding, mixed copper mineralogy, complicated galvanic interactions, economic levels of gold and silver, and high levels of impurities such as arsenic. There is currently no established methodology for separating arsenic-bearing copper minerals from other copper sulphide minerals by flotation. The possibility of separating arsenic-copper sulphides from other copper minerals by controlling the potential of the flotation pulp has been shown in previous studies. However most of these studies were conducted on single mineral systems and the selective removal of arsenic-copper minerals in complex ore systems is not well understood. The flotation behaviour of arsenic-bearing minerals within complex ores differs significantly from that of pure mineral systems due to the effects of mineralogical composition, the degree of liberation, and the surface oxidation. The understanding and manipulation of these effects can lead to improvements in the selective flotation recovery of arsenic-bearing species from complex ore systems."

Jan 1, 2018

By Kamalendu Bhunia

With the progressive depletion of known resources of good quality coal and minerals as well as the increasing demand of these minerals by different user industries, the emphasis has been shifted all over the world from selective mining to bulk mining followed by up- gradation to obtain the required quality of concentrate. The column flotation cell is one of the alternatives to reduce the gangue content of fines because of its inherent characteristics viz. easier to operate, low space required, no moving parts etc. A laboratory flotation column is used to conduct experiment. Present work has been undertaken to observe the effect of process variables (gas flow rate, feed/slurry flow rate, and frother concentration) on gas dispersion parameters (gas holdup, bubble surface area flux) in collection zone and to explore the effect of feed (slurry) inlet orientations and gas flow rate on column?s metallurgical performance. The effects of solid particle concentration, size and type (hydrophobic and hydrophilic) of solid on gas dispersion parameters have also been investigated. Test work has been performed in a continuously operating Perspex column (10 cm in diameter and 168 cm in height) using coal, sphalerite and dolomite as solid. Gas hold-up has been measured by phase separation method and mean bubble sizes are estimated from a drift flux analysis. The influence of operating parameters on bubble surface area flux has been discussed. It is observed that gas holdup in collection zone is affected by air as well as feed flow rates and also solid?s type. It is also found that addition of solid decreases the gas holdup and rate of decrease in gas holdup increases when solid concentration increases and particle size increases. Increase in gas flow rate increases recovery in collection zone due to increase in number of bubbles per unit volume of the column. From the experimental results it is evident that cross-current orientation of feed inlet shows slightly better metallurgical performance compared to other orientations. Keywords: column flotation, gas holdup, drifts flux, bubble size, bubble surface area flux, hydrophobicity, and recovery

Sep 1, 2012

By X. Q. Ma

The beneficiation test on low grade phosphate ore from a state of Russia is carried out. The rougher-cleaner ? re-cleaner system is used in the flotation process, The fineness of grind is 39.07% minus 200 mesh. The result indicates that concentrate containing 31.25% P2O5 can be obtained from the flotation feed assaying 6.18% P2O5, with 93.54% P2O5 recovery. The test result is also a guideline for further development of some currently operated phosphate beneficiation plants.

Jan 1, 2014

By Z. Pokrajcic

The traditional comminution circuit is a major consumer of energy ? both as electrical energy and through consumption of media and wear resistant liners. Up to 40% of electrical energy con-sumed at a mine site is attributed to comminution however only a few percent of this energy is used in the generation of new surfaces from size reduction. This paper describes the evaluation of modifications using simulation models based on two operating comminution circuits. The aim of these modifications is to decrease both the amount of electrical energy consumed in the size reduction process, known as direct energy, as well as to decrease the consumption of grinding consumables such as steel grinding media and mill liners, designated as indirect energy. The approach is two-fold: ??Employ, where possible, autogenous grinding techniques to eliminate the need for grinding media and reduce mill liner wear. ??Optimise the use of the grinding energy distribution in the comminution circuit by using more energy efficient grinding devices to target typically problematic features of a comminution circuit such as critical size material from the primary mill and overgrinding in the secondary mill. The investigations show that significant total energy savings, as high as 50% in some cases, can be achieved by employing the techniques described while maintaining circuit throughput and product size. Investigations also show potential benefits in downstream flotation processes as the product size distribution generated from the eco-efficient circuit is generally ?narrower? in shape for improved flotation performance and containing less material in the coarse fraction for overall better liberation.

Jan 1, 2014

By R. C. Dunne

As ore grades of existing and new ore deposits continue to decrease there is ever increasing pressure to decrease operating costs to maintain profitabitabitiy at existing mine sites and for new projects. The accepted solution to this dilemma in most cases is to increase treatment rate, leading to a coarser grind, at the expense of marginal decreases in recovery. The recovery loss is usually associated with losses of liberated and composite coarse material. This paper will review the practice of coarse particle flotation, including the reagent chemistry, cell hydrodynamics, froth stability, entrainment and flotation cell design, all parameters important to the recovery of coarse liberated and composite particles. This will provide a better understanding of opportunities to improve the recovery of coarse particles. Some examples will be provided.

Sep 1, 2012

By Long Han, Jianyuan Liu, Ping Ying

"Particle-bed compressive stressing is the main work mechanism of comminution by high pressure grinding rolls(HPGR). An experimental study on comminution and mineral liberation of two copper sulfide ores was carried out using a piston-die compressive stressing rig to simulate the situation of comminution with HPGR as the final-grinding device. The tests carried out include compressive comminution tests on particle-bed with narrow-size feed, and the locked-cycle comminution test on particle-bed with broad-size feed, which was then compared to a corresponding locked-cycle test of ball-mill grinding. The narrow-size feed is made up of particles in the size range 2.36~3.35 mm, whereas the broad-size feed of particles in the size range 0~3.35 mm. The liberation analysis for copper-mineral in the comminution products was accomplished using BPMA system – an automatic mineral liberation analyzer developed by BGRIMM. The influences of the stressing intensity and the method of comminution on the copper mineral liberation are discussed in terms of product size distribution, copper-metal deportation among size fractions, distribution of copper mineral among particle-size and particle-grade classes, degree of mineral liberation in size class as well as degree of mineral liberation overall.INTRODUCTION Traditionally, comminution process commonly applied in mineral processing is a flowsheet consisting of crushing of crude ore with conventional crushers, followed by grinding of the crushed ore in tumbling mills. In last decades, the energy-efficient HPGR (high-pressure grinding rolls) has found its application in mineral processing, mostly as tertiary or quaternary crusher to generate a fine-crushed product either as feed to subsequent grinding or as feed to a pre-beneficiation process before further grinding. Compared with the process of conventional crushing followed by grinding in ball mill, this mode of HPGR-application can achieve energy saving to some extent by reducing particle size of the feed to ball milling, and by reducing amount of the feed to ball milling if a significant portion of tailings in relatively coarse particle-size range can be discarded at the pre-beneficiation stage. In recent years, the approaches of letting HPGR take more comminution work from ball mill by applying it in semi-finish grinding mode or even finish grinding mode have been discussed (Burchardt, 2014). Although HPGR finish-grinding has been successfully applied in the cement industry for grinding of cement clinker and raw materials, this mode of HPGR application has yet rarely been implemented in mineral processing, despite the advantage of more energy-saving and other potential benefits such as preferential breakage, internal damage of particles and enhanced mineral liberation which may lead to a better downstream processing performance. The reasons for the retardation of the progress of this kind of HPGR-application in the mineral industry lies not only in that a finish-grinding with HPGR has to be operated in dry condition whereas most of ore-beneficiation processes like flotation are operated in wet condition, but also in that there are large variety of ore materials with various complexity of processing technology, which need to be addressed on a case-by-case basis with a lot of test work, in order to evaluate the potential advantages or disadvantages of this application."

Jan 1, 2018

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By Xiqing Wu, Tao Yue

"Magnetic seeding co-agglomeration, i.e. adding magnetic seeds, organic depressant (such as the starch), and pre-magnetization for co-agglomeration, was applied in the reverse flotation for hematite ore slimes. Samples of the hematite ore slimes and the pure hematite fines were investigated by the co-agglomeration, respectively. Flotation tests suggest that the depressing effect of starch in the flotation was further enhanced with the addition of magnetic seeds and the pre-magnetization. Following the laser size analysis and flotation tests, TOC adsorption analysis, VSM, surface charge measurement, AFM, FTIR study, and SEM imaging have been utilized to understand the depressing mechanism. Based on the results it was demonstrated that with the addition of magnetic seeds and the low field pre-magnetization, the adsorption of starch onto hematite minerals was strengthened through the magnetic seeding co-agglomeration. The co-agglomeration improved the flotation performance by introducing the magnetic interactions and acting the bridging adsorption of starch between fine hematite and magnetic seeds in a suspension, and then resulting in an intensified coverage of the starch onto hematite particles and positive action in the coagglomeration under the pre-magnetization.INTRODUCTIONFlotation is undoubtedly the most important and versatile mineral processing technique, and both its use and application are continually being expanded to treat greater tonnages and to cover new area. However, its influence was limited to a relatively narrow particle size range of 5–300 µm (Wills and Napier-Munn, 2006). The main reason behind this limitation lies in that fine particles have high specific surface area, so need relatively high dosage of reagents (collectors or depressants), and exhibit poor flotation performance while intermediate or properly-sized particles produce high flotation kinetics and need low consumption of reagents. In order to increase the recovery of fine particles, quite a few of flotation techniques have been investigated. Most of them are based on particle aggregation, namely, by enlarging the apparent particle size, such as carrier flotation (Valderrama and Rubio, 1998; Zhu et al., 2009), shear flocculation (Duzyola and Ozkan, 2010; Yin et al., 2011), selective polymer flocculation (Rubio et al., 2007; Song et al., 2012; Ng et al., 2015), oil agglomeration (Laskowski and Lopez- Vladivieso, 2004; Forbes, 2011), temperature responsive polymer flocculation flotation (Forbes et al, 2011), and etc. However, these techniques above-mentioned are mainly studied for the direct flotation of fine minerals, and most of these techniques have not found applications for iron ore slimes especially recovered by the reverse cationic or anionic flotation."

Jan 1, 2018

By A. Vilinska

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineral-solution interface. Recent developments in biotechnology have not only aided hydrometallurgical leaching operations but also shown great promise in mineral beneficiation processes. The adhesion of bacteria on minerals alters the surface properties relevant to flotation and flocculation of minerals. The biomodification of mineral surfaces occurs through the attachment of microbial cells, oxidation reactions and adsorption or chemical reaction with the metabolite products. Several types of heterotrophic and chemolithotrophic bacteria have been successfully applied in flotation and flocculation processes for the last two decades. Al-though the potential of microorganisms in minerals beneficiation has been realised by several re-searchers from their laboratory investigations, the studies were mostly confined to pure mineral systems and there is hardly any sincere effort to apply the methodologies on ores. This paper presents a brief summary of the literature in bioflotation and bioflocculation, and attempts to outline new dimensions of research for a practicable application of this technology in mineral industry.

Jan 1, 2014

By H. R. Zhang

In this paper two optional production processes are presented for reasonable utilization of primary sylvinite in Qinghai province, China. The two kinds of products as chlorine-free potash fertilizers; potassium sulphate or potassium magnesium sulphate can be obtained. In the course of potassium sulphate production, using primary sylvinite from Qinghai salt lake as raw material with impurities such as sodium chloride and insoluble in primary sylvinite, it must be prepared by flotation before being converted into potassium sulphate. This final product has found wide use in tobacco industry in China. However, in some cases Chinese farmers would rather buy the fertilizer of potassium magnesium sulphate than high quality of potassium sulphate. With flotation process which is a little different from above mentioned, the potassium magnesium sulphate fertilizer may be produced by washing one of the flotation concentrate presented as picromerite, while another concentrate containing potassium chloride is treated as by-product.

Jan 1, 2014

By W. Q. Zhao

In order to raise the utilization rate of phosphate resource of Al-Jalamid Mine in Saudi Arabia, a flotation experiment for its phosphate rock was carried out by using WF-01collector that have been produced by Wengfu Phosphate Mine. The results showed that WF-01 collector had extensive adaptability for Al-Jalamid phosphate rock, and the grade of phosphate concentrate could be up to 33% P2O5 mixing the upper, middle and lower beds rock as well as its 80% more recovery.

Jan 1, 2014

By A. V. Abshilawa, D. G. Talakhadze, R. I. Sturua

"Processing of the tailings accumulated over the lifetime of Madneuli Copper Concentrator is an opportunity to extract additional salable copper and gold products. This paper presents a pre-concentration process for the valuable components (copper and gold) of the accumulated tailings. The developed process makes it possible to obtain a copper pyrite concentrate with a yield of 14.05%, copper grade of 1.36%, and recovery of 83.22% containing 3.78 g/ton of gold at a recovery of 84.31%. The bulk concentrate is produced by a combined process bringing together selective flotation to produce salable copper concentrate and hydrometallurgical processing of the selective flotation tailings to recover gold. KEYWORDS: FLOTATION, ALBION PROCESS, LEACHING, COPPER CONCENTRATE, SELECTION Madneuli Copper Concentrator, Georgia, was put into operation in 1975. Over its lifetime, 40 mn tons of tailings have been accumulated at the tailings storage facility (TSF). Sampling of the TSF has indicated that the average copper and gold grade is 0.23% and 0.56-0.65 g/ton, respectively. Accordingly, the TSF can be classified as a technogenic reserve. This paper discusses pre-concentration of valuable components using flotation, followed by processing of the bulk concentrate in the Albion process. Mineralogical analysis of the accumulated tailings showed that the main ore mineral is pyrite (11.71%). Copper minerals are mainly represented by chalcopyrite (0.7%). The main nonmetallic mineral is quartz (67.3%); sericite, chlorites, etc. also occur. Pyrite is present both as liberated grains and intergrowth. The absolute majority of copper minerals are found as intergrowth with pyrite, less often with quartz. Ore minerals are slightly oxidized. Chemical analysis results are shown in Table 1. Particle size distribution shows that the size class -0.2 mm - 0.045 mm has the highest grade of 0.85 to 0.97 g/ton of gold. Size class +1.25 mm has the lowest grade. Based on the chemical and mineralogical studies and particle size distribution, an optimized process was developed for pre-concentration of the valuable components prior to hydrometallurgical processing. Several gravitation, direct selective, bulk, and bulk selective flotation processes were trialed. (1,2)"

Jan 1, 2018

By D. Moradkhani

The objective of this research was, to evaluate the hazard of heavy metals in the soil around the National Iranian Lead & Zinc (NILZ) Company. In this study, 38 samples of soil around the NILZ factory were collected using standard sampling method, so that, the heavy metals Pb, Zn, Cd and Cr have been evaluated. The concentration of heavy metals were measured and compared with standard limits. The results show that the hazard of heavy metals in soil is not so serious and the content of Pb in just 5 percent of samples, and the content of Zn in just 3 percent of samples were above standard limits and the concentration of Cd and Cr were under the standard limits. Average, variance and standard deviation of the elements are calculated and with due attention to the standard deviation, Pb and Zn are seen to be more distributed than Cd and Cr. Also the isograde curve of heavy metals was drawn using software called Surfer. These curves showed that the heavy metals are concentrated at particular distances from the factory. Keywords: heavy metals, remote sensing, sampling method, isograde curve, Surfer software

Sep 1, 2012

By Y. Y. Emelianov

The results of the test work of four treatment options of three refractory gold-pyrite and gold-arsenic flotation concentrates are presented. These concentrates were obtained during the concentration of primary ores of large gold deposits. It was found that ultrafine grinding of refractory flotation concentrates did not increase the recovery of gold during subsequent cyanidation. The elimination of sulfur and arsenic during oxidative roasting is 99 per cent. 88-93 per cent of gold is recovered by cyanidation from calcines. After biooxidation of the flotation concentrates with a mixture of strains Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans 88-91 per cent of gold is recoverable by direct cyanidation. The recovery of gold from flotation concentrates by pressure oxidation is 88-99 per cent. These results suggest that gold recovery is important but the following strategies would have an impact on a plant performance and would be considered when developing an option to treat refractory ores: capital and operating costs, ore reserves, mine location, infrastructure and qualified staff. Keywords: gold, flotation concentrates, recovery, cyanidation, roasting, biooxidation, pressure oxidation

Sep 1, 2012

By Antoineta Boteva

A significant part of the currently production of the non-ferrous and precious metals is from sulfide ores. Character feature of sulfide ores is the presence in them always pyrite and wide range of different sulfide minerals else. These minerals are the carriers of valuable for industry metals. Due to the low content of the main components, very often call on the use of collective- selective flow-sheets. The extraction of minerals in the collective concentrates determined in a large extent the effectiveness of the collective-selective sheets. In conditions of bulk flotation kinetics to floatate of the various minerals is different. Due to why it is and how it can be used for a more effective selection of minerals ?this is the main task of this report. For this purpose are used results from the bulk flotation of pyrite, copper sulfides, molybdenite, galena, blenda. It is separated and place of host rocks. Base it of large experimentation material, including both electro-kinetic measurements of mineral systems, as well as laboratory flotation tests and factories monitoring it is established kinetics of flotation of mineral particles in conditions of collective flotation. Made an effort to clarify the effect as of the species and the proportion of different sulfide minerals involved in flotation pulp else. Traced was the impact of the density and aeration of the flotation pulp on deferens in kinetics of mineral flotation in condition of balk flotation. The obtained results are used to increase the efficiency of the diffraction flotation of the complex sulfide ores containing precious metals. In the schemes, it is possible precious metals to fall in the most appropriate for the next processing products. Keywords: flotation, sulphide ores, kinetic extraction

Sep 1, 2012

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

In order to determine the optimal process parameters of agitation leaching and provide industrial process design parameters, experiments were carried out on leaching behaviors of copper oxide ore with high mud content. Condition tests show that the main factors affect the leaching efficiency as follows: Temperature, Initial acid concentration, leaching time and particle size. As the temperature increases, the copper leaching rate was increased. At 60 ?, the initial acid concentration 80g / L, leaching time 2h, liquid-solid ratio 2:1 and grinding fineness65%-0.074mm, the optimal copper extraction was 83.15%, the acid consumption was 187.91kg / t. ore. Keywords: agitation leaching, copper oxide ore, mud

Sep 1, 2012

By Yu. E. Emelyanov, A. V. Bogorodsky, R. N. Nabiulin, S. V. Balikov

"The paper describes the results of the study of gold-copper flotation concentrate atmospheric oxidation at different sizes of material, varying oxidation time, with air or oxygen blow. The study showed the low rate of sulphide oxidation during oxidation of flotation concentrate at a feed size (P98 -74 µm). The coppery recovery into solution was 48%; the recovery of gold by subsequent cyanidation reached 86%. Preliminary flotation concentrate grinding to P98 -20 µm provided oxidation of 90% of copper minerals, 80% of arsenopyrite and 15% of pyrite. The gold recovery by atmospheric oxidation of a fine-ground flotation concentrate increased by 59%, from 36% to 95%, the NaCN consumption reduced by 21 kg/t, from 30 to 9 kg/t. INTRODUCTION Processing of sulphide gold-copper ores and concentrates using conventional cyanidation technology results in higher reagent consumption and lower gold recovery. Destruction of sulphide minerals and extraction of copper from a processed product prior to cyanidation is essential for improving efficiency of precious metals recovery and reducing main reagents consumption. Atmospheric oxidation (AO) is one of the most promising hydrometallurgical methods of refractory gold-copper concentrates processing, along with biooxidation and pressure oxidation. The nature of this approach lies in oxidation of sulphides at 90-95°C, in acidic or alkaline conditions, with bubbling of oxygen or air, after preliminary ultrafine grinding (1-4). The following reactions of sulphide oxidation occur during atmospheric oxidation of a gold-copper flotation concentrate. Pyrite is oxidized with the formation of ferric sulphate (1) and elemental sulphur at low temperatures (2), whereas some portion of elemental sulphur reacts to form sulphuric acid: FeS2+3,75O2+0,5H2O=0,5Fe2(SO4)3+0,5H2SO4; ?G=-1144,02 kJ/mol (1)"

Jan 1, 2018