Search Documents

By Charles Kocsis

Over the last few years a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell powered equipment into underground mines to replaced diesel engine powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine?s energy consumption, its associated greenhouse gas impact and also reduce a mine?s significant ventilation associated costs. Fuel cell powered equipment also has the advantage of lower noise and heat production compared to their equivalent diesel powered counterpart. The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions and minimum velocity requirements. However another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations these factors change, dispersion and buoyancy are limited; time may not be available and in non-coal mines ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical, consequently ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation such as a hydrogen leak from the fuel cell stack or its distribution system.

May 1, 2007

By E. M. Watkin

"Land directly disturbed by hard rock mining activities in Ontario and Quebec was surveyed in 1974 as part of a country-wide assessment, (Murray 1977). Some 15, 000 hectares, or 5 7 square miles, are listed as having been disturbed by overburden removal, waste rock and tailings deposition (Table 1) in the region. That area represents sixty-eight per cent of the total area which ha1; been disturbed by mining in central and Atlantic Canada. Assessment of disturbed areas was undertaken using LANDSAT-1 and LANDSAT-2 satellite imagery. Certain limitations of the technique were recognized but the data obtained were considered a relatively acceptable assessment of the extent of disturbed areas larger than ten hectares.Approximately ten per cent of the land disturbed by mining in the two provinces has been reclaimed to varying degrees. Indeed, this proportion is correct for the country as a whole. As pointed out by Ripley, Redmann and Maxwell (1978), some of the land was disturbed long before environmental concern 01· reclamation were ever considered. In numerous instances reclamation will remain impossible until presently active operations are closed. Nevertheless, these authors feel such figures make it clear that reclamation has not been a high priority in Canada in the past. Canada is a vast country, and there has been little pressure toward efficient use of all land space. Most mining operations occur in areas distant from the country's population centres. Under these circumstances, therefore, the pressure to reduce the environmental impact of mining is much less than in the more densely populated areas of Europe and the eastern United States, where such activity can occur in or adjacent to large metropolitan areas."

Jan 1, 1980

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By Benoit Bissonnette

"The need for production of a competent fill was recognized early by the project partners. Consequently, a 4000 Ud paste fill plant was constructed and commissioned in early August 1994.In order to fine tune the process without risk to the underground workings, a closed pumping loop was devised on surface. After two months of this exercise, the first underground slope was filled according to specifications obtained from the pilot plant trials.This paper will focus on the operational problems encountered and the solutions adopted so far, and on a comparison between expected and actual fill production and characteristics.RésuméLa nécessité de produire un remblai de propriétés mécaniques suffisantes a été rapidement reconnue par les partenaires du projet. Conséquemment, une usine de production de remblai en pate, utilisant les residus du concentrateur d'une capacité de 4000 t/j a été construite et l'opération a débuté au mois d'aôut 1994.Dans le but de roder le précedé sans mettre en danger les installations souterraines, l'usine a été testée dans un circuit de surface. Après deux mois d'essais, le premier chantier souterrain a été rempli avec du remblai en pate selon les specifications dérivées de l'usinage pilote.Cet article présente les problemes d'opération rencontrés et leurs solutions, en plus de faire une comparaison entre les résultats prévus et ceux actuellement obtenus sur la production et sur les charactéristiques du remblai."

Jan 1, 1996

By Barrick Pierina, John Frostiak, Igor Gonzales, Kenneth G. Thomas, Ken Manning

"1.0 SummaryThe Pierina deposit was acquired in August 1996 when Barrick Gold Corporation purchased Arequipa Resources, a junior mining company with extensive land positions in Peru. At the time of acquisition, Arequipa had developed two exploration tunnels and drilled 9 exploration holes on the property. Metallurgical tests, conducted on samples taken from the tunnels and the exploration holes indicated that the ore was amenable to heap leaching. Barrick’s exploration team recognised from the outset, the potential of the mineralisation and convinced Barrick’s senior management that this was indeed a world class deposit that should be pursued. On November 25, 1998, the first dore was poured at Pierina, 27 months from the time of acquisition. During that period Barrick completed its exploration programme, prepared a development plan including capital and operating costs, production profiles and cash flow forecasts, and a schedule to develop a mine and construct a leach pad and gold recovery plant, including all supporting infrastructure. All permits and environmental approvals were obtained and all necessary land was acquired. The project was completed on schedule and under budget. This was the first greenfield mine development for Barrick outside of North America.This paper details, mainly, the research and development, engineering, construction and commissioning of the metallurgical process facilities.2.0 The Develonment ProgrammeImmediately after the acquisition, Barrick began the process of gathering information required to prepare a project development plan. Kilborn Engineering was retained to assemble all of the information collected and collated into a development plan document. This document was completed by June 16,1997. The objective was to bring the mine into production as quickly as possible with critical activities identified as follows:"

Jan 1, 2000

By Dominic Fragomeni, Tony DiFeo, Martyn P. Hay

"As part of an investigation into flotation modelling of industrial scale operations, Falconbridge Ltd organised a “blind” test of the SUPASIM flotation model developed by Eurus Mineral Consultants (EMC). Two sets of rougher rate data, a flowsheet and the number and size of cells in the rougher bank were supplied from a plant that had been previously surveyed in November 2003. The name of the plant, cleaner circuit details and circuit mass balance were, at the time, unknown to EMC. With only these data, flotation performance was simulated and the cleaner circuit sizedFalconbridge then compared predicted and actual float performance and mass balance and found that final concentrate recovery and mass and circuit cell volume matched closely. Simulated recoveries relative to actual were +0.4% Cu, +0.1% Ni and -0.7% Co. However, prediction of metal distribution in the internal streams making up the various circulating loads showed some sizeable errors. On this initial success, the trial was extended and additional float test data for rougher feed, cleaner feed and cleaner scavenger feed was generated on site in April 2005. Further simulations significantly improved prediction accuracy for metal distribution in the internal streams. The average difference between predicted and actual recovery for all streams was reduced from 10.5% to 0.4%. This updated simulation was then used to ascertain the impact on final recovery, grade and plant circulating loads of increasing feed tonnage from 114 to 150t/hr. A number of scenarios were simulated in order to understand the contribution that (a) the fast and slow floating fractions and (b) regrinding of cleaner tailings are making to overall plant recovery.Simulation was then used to determine how much the flotation kinetics of both rougher feed and cleaner scavenger feed have to increase in order to deliver a 1.5% improvement in overall plant recovery. These improved kinetic values provide a target for laboratory testwork and operating conditions can be varied to determine how best to achieve these new values of fraction and rate."

Jan 1, 2006

By S. L. Aaroe

"TYRETHANE PRODUCTSTyrethane® is the family brand name which has been adopted by The W. S. Tyler Company of Canada, Limited to identify its polyurethane products. Since we have been manufacturing Woven Wire Cloth for over one hundred years and have been the innovator for most of the product improvements and developments of that industry, it is only natural that our first and primary efforts involve the use of Tyrethane® as a screening medium. The product is ideal for application in the mining industry and other operations where the rate of wear on existing media is exceptionally high.In the event that you have already had some experience with polyurethane it should be poirted cut that there are many grades of the material. The polyurethane used in Tyrethane® Products will be compounded in a variety of chemistries and different heat treatments will be used to develop best mechanical properties to handle specific applications. However Tyrethane® will not be a ""cure all"" but when it is properly applied as a screening medium it will assist by lowering the unit cost for screened materials.Prior to an explanation of the advantages of Tyrethane® let's review the conventional screening media whose applications may be considered as good candidates for replacement by Tyrethane®.1.,Woven Wire Cloth.2.,Perforated metal screens.3.,Rubber faced perforated metal screens.4.,Perforated rubber screens.5.,Cast steel screen segments and weldiments.6.,Profile wire.In most cases a Tyrethane® section is designed for a one for one replacement of the material now being used. It is rarely necessary to modify the screening equipment to enable you to install the Tyrethane® Product although it may be desirable to take some steps to improve the service life of hold down components such as Clamping Strips or Tension Members. Those parts can be encapsulated in polyurethane if necessary.To fabricate the Tyrethane® section we have three basic building blocks. They are: (1) Small molded segments having square or slotted openings, (2) Reinforcing material and (3) the raw liquid polyurethane."

Jan 1, 1976

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By H. R. Bullis

"Abstract- This paper discusses what appears to be a flaw in the current belief, widely held within the gold mining industry and investment community, that the creation of ever-larger gold mining companies is desirable for mining companies and investors alike. The basis of the flaw is in the underlying assumption that very large gold producers can discover or acquire new gold deposits of the size necessary to replace extracted reserves on a year-on-year basis over the intermediate to long term (i.e., five to ten years and longer). As it will be noted in this paper, deposits of the size required to replace annual production of very large gold producers (VLGPs) are relatively few in number. Although discoveries of new gold deposits continue to be made, they are predominantly in the 0.5 to 2.0 million ounce range. Data represented here suggest that, although gold production from individual VLGPs continues to increase, the change is due to merging or acquiring other companies or projects with similar reserve life profiles. Therefore, the reserve life profiles of VLGPs have remained flat or have decreased.The paper will note recent changes in the industry and the remarkable increase in gold production reported by individual mining companies over the past several years. It will provide an overview of the geographical and geological distribution of known gold deposits and the range of deposit sizes. Finally, the paper will discuss the challenges that face large gold producers in replenishing their reserves that are being depleted at an ever-increasing rate. Unless otherwise stated, all production and reserve data have been taken from company documents in the public domain or publicly available information."

Jan 1, 2001

By R. Gallinger

In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale. The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP?s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP

May 1, 2005

By Bassam Kattaa

"Abstract - A heavy mineral survey of beach and dune sands including geochemical analysis for trace elements was undertaken to evaluate the economic potential of the sands and to understand the nature and distribution of the heavy minerals relative to potential source rocks. Results indicate that heavy minerals are generally derived from outcropping volcanic rocks that comprise a proportion of the hinterland in the south part of our survey area. The most abundant minerals are magnetite and pyroxene. The morphologies of the heavy mineral grains are angular to subangular, suggesting that they were transported short distances from the source rocks. Factors controlling heavy mineral distributions include wave and wind action, proximity to provenance, the fluvial drainage network, and longshore currrents.The most economically important mineral is ilmenite. Zircon and rutile concentrations are relatively minor and thus have lower economic potential."

Jan 1, 2002

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By Fathi Habashi

"A process is proposed for the treatment of phosphate rock for the recovery of uranium and the lanthanides. The process assures the production of phosphatic fertilizers without polluting the environment with radioactive material.IntroductionWhile many processes for uranium recovery from phosphoric acid produced by the H2S04 route are known and utilised commercially, little is known about uranium recovery from phosphoric acid produced by the HN03 route1. Advantages of the latter route are both the elimination of the gypsum disposal problem, and the possibility of radium disposal in a controlled way2. Further, the lanthanides originally present in the rock can be recovered if the nitric acid route is used; they will be mostly lost in the gypsum produced by the sulphuric acid route3. In the present work a scheme for the recovery of uranium and the lanthanides from phosphate rock without interfering with the normal route for fertiliser production is proposed using HN03 as a leaching agent. Attention was also given to uranium decay products and their separation so that they might not contaminate the fertiliser4. Further, an attempt was made to defluorinate the leach solution in order to upgrade the fertiliser and at the same time recover the fluorine5. Rapid analytical methods for the determination of uranium, radium, and lanthanides in phosphate rock were developed6,7."

Jan 1, 1997

By A. Vien, B. C. Flintoff, R. P. Edwards

"A major thrust in industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements in control performance can be achieved by getting back to the basics.IntroductionEvery modem concentrator has a state-of-the-art computer control system in place. Several of these are contemplating installing, or have installed, advanced control systems, such as expert systems, but the foundation of their control system remains the PI controller. Although the authors are not aware of any survey or published information for the mineral processing industry, it is reasonable to assume that it would be similar to the pulp and paper industry. ""The average [pulp] mill has some 2000 control loops of which 97% use PI control. This means that PID, dead time compensation, adaptive controllers, specialized algorithms, ... , constitute only 3% of the installed base."" (Bialkowski [1992]).Bialkowski [1992] also stated that ""If you have been keeping score, only 20% of the loops surveyed actually decrease variability in automatic over manual mode of operation, in the short term."" He attributed the problems to: poor tuning (30% of all loops), control valve problems (30% of all loops) and process problems (20% of all loops). There appear to be a serious need to go back to basics and review the existing control system."

Jan 1, 1998

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By G. H. Hope

"Pamour Porcupine Mines of Timmins, Ontario operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the area. The area milling concept was adopted by Pamour in 1971 and has been used successfully since then. The purpose of this paper is to discuss the advantages and the problems of area milling. Pamour Porcupine Mines Limited operates two 3,000 ton per day concentrators which receive ore from eight to ten mines in the Porcupine region. The area milling concept was adopted as the route to survival for Pamour and has worked successfully. HISTORICAL BACKGROUNDProduction of gold from the Porcupine region in Northern Ontario started in the early 1900's and has been continuous since that time. Some of the major operators were companies such as Mcintyre, Hollinger, Dome, Pamour, Paymaster and the list goes on. An underground survey would reveal hundreds of miles of drifts and raises. The main group of mines extends from South East of Timmins to the Pamour Mine, 15 miles to the east. During the lean years of the sixties when gold prices were low, labour costs were rising rapidly, and ore grades were dropping, many of the area mines closed down their operations."

Jan 1, 1981