Search Documents

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses collector residuals, metal concentrations in solution, and other parameters.Collectors used in the plants studied were various xanthates, Z-200, and Aerofloats. Xanthate residuals varied in different ways in most plants. However the general trend was for residuals to be at the O· 5-2 p.p.m. level in lead flotation and O· 5 p.p.m. or less in zinc flotation.Aerofloat residuals were also variable but in the plant concerned were at a much higher level (8-10 p.p.m.) than xanthate residuals. Z-200 residuals were in the 10-20 p.p.m. range and it was found that the Z-200 added to zinc flotation was reporting in dam return water and entering lead flotation.Copper concentrations in solution were negligibly low in those plants where cyanide was not used. When cyanide was used, copper was at the 5-20 p.p.m. level and appeared to be present as Cu(CN)-2. However the hiocyanatepresent may be important. Xanthate was also present in these solutions.Zinc concentrations ranged from 0·1 to 800 p.p.m. in different plants. The general trend was for the zinc level to be highest in the grinding circuit and to drop during flotation. However there was always an increase in zinc concentration when copper sulphate was added, even tho.ugh this incre.ase was not permanent, and the increase was greater with higher copper sulphate additions.The manganese concentration also increased appreciably during copper-activation of marmatite. In some plants lead concentrations increased from 0·1 to 1 p.p.m. during activation of marmatite.Calcium concentrations (20-1200 p.p.m.) and magnesium concentrations (10-600 p.p.m.) tended to be fairly stable in each circuit.

Jan 1, 1970

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

The Mineralogy and Reactivity of Pyrrhotite from Selected Nickel Ore Deposits and its Effect on Flotation Performance

Sep 13, 2010

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Authors have been conducting research on autonomous loading operation by wheel loader. Autonomous loading cycles has been demonstrated with real size experimental model. In V shape loading operation, travelling between scooping point and dumping point is dominant factor for cycle time of the operation. The positions of scooping point and dumping point changes with advancing the operation. In the developed system, path planning is performed at the beginning of every cycle. The path is formed by combination of curve and straight path elements. During travelling on the planned path, path following control is applied on the loader to keep position error in narrow range. Positioning of the loader is based on dead reckoning with correction by global positioning system (GPS) data. In a process of path following control, control value for steering angle is determined based on position error in lateral direction. Proposed method of path planning and position control is installed and tested in the real size experimental model. The detail and results will be described in the paper.

Dec 6, 2010

Exerting the Advantages of National Key Discipline, Outstanding the Training of Engineering Capability, Cultivating Talent to be with Innovation Ability

Sep 13, 2010

By P K. Smith, R J. Ryan, W R. H Ramsay, D C. Arne, F P. Bierlein

Turbidite-hosted, mesothermal lode gold deposits in Paleozoic metasedimentary rocks of the Buller Terrane, western South Island have a similar geological history and genesis to the Paleozoic lode gold deposits ofVictoria, Australia and Nova Scotia, Canada. In all three regions the gold deposits are hosted by interbedded meta-sandstone and meta-argillite that have been folded and regionally metamorphosed to greenschist facies, and locally in Nova Scotia to amphibolite facies. The gold deposits are typically narrow, structurally controlled quartz veins associated with dilatant zones in reverse faults or fold-related fractures. The principal vein types include: bedding parallel or concordant veins, discordant veins, saddle reefs, and stockwork veins. En-echelon and "ac" type veins are sometimes also gold-bearing in Nova Scotia. The contrasting competency of the host meta-argillite and meta-sandstone beds is an important factor in vein formation, particularly for the bedding parallel veins, which are typically developed within meta-argillite beds or along the contacts between meta-argillite and meta-sandstone. Veins found within meta-sandstone units are generally discordant. The deposits in Victoria are well known for their bedding-parallel veins, saddle reefs ( Bendigo ) and leather jacket reefs (Ballarat). Bedding-parallel veins are also common in Nova Scotia , along with a few examples of saddle reefs. In contrast, vein formation probably occurred later in the deformation history of the Reefton and Lyell goldfields, with most veins being bedding discordant and more typically aligned with the axial plane cleavage of the folds rather than bedding planes. The quartz lodes in one deposit, Globe-Progress, strike approximately perpendicular to the bedding and fold axes. No saddle reefs have been recorded from the Buller Terrane. Mesothermal vein morphology reflects the amount of fmite strain, the strain rate, competency contrasts, lithotypes, and the confirming pressures to which the system was exposed. On the basis of comparable depositional depths and rheologies of the host rocks, a controlling factor influencing the development of different vein styles (and timing) might be finite strain, as exemplified by the tightness of folding in the host rocks. Folding appears to be tighter in the Victorian rocks than in either the Buller Terrane or Nova Scotian rocks.

Jan 1, 1999

A study was made of zircon powders bonded with phosphoric acid or aluminium orthophosphate. The influence of strength of solution of the phosphatic binders on the modulus of rupture over a temperature range was investigated. Physical properties of three grades of zircon powder bonded with phosphatic binders were studied at various temperatures. Examination of x-ray diffraction data indicated that phosphates ofzirconia are preferentially formed to phosphates of silica. However, zircon in the presence of excess phosphoric acid also forms phosphates of silica upon heating.Resistance to attack by slags from blast and open hearth furnaces was determined on phosphate-bonded zircon mortars in a cup test with industrially made ladle bricks. Zircon powders bonded with phosphates proved to have high P.C.E. values. The first satisfactory results of a plant trial with phosphate-bonded zircon mortar, used in a steel ladle, are now being assessed in larger scale industrial tests prior to accepting the mortar as a steel plant refractory.

Jan 1, 1972

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992

Effect of Activated Carbon on the Leaching of Cobalt-Rich Ferromanganese Crust in Sulfuric Acid

Sep 13, 2010

Concentrations of bright green material in the "Golden Mile" of Kalgoorlie, which carry particularly high gold values, are known locally as "green leader".This assemblage consists largely of quartz, sericitic muscovite, carbonates, and pyrite. Some of the sericitic muscovite contains vanadium, giving the rock its green colour. Vanadium oxides, including nolanite, are also present. Tellurides identified in this study are calaverite, altaite, petzite, melonite, and coloradoite. Native gold was found in most of the samples; some of the gold, at least, has been formed from the decomposition of gold tellurides.It is suggested that mineralizing solutions carrying gold and tellurium leached vanadium from the host rocks and subsequently deposited gold tellurides and vanadium-bearing minerals in the "green leader".

Jan 1, 1977

During the course of the major research in the Metallurgy Department of the University of Melbourne into the creep characteristics of lead and .its dilute alloys, it has been the practice to prepare the majority of test specimens from rolled strip. From time to time during the progress of the work, certain variables involved in. the rolling of the experimental ingots have been investigated. It is proposed to collect together in this paper the results of these experiments. Some general features relating to the type of deformation produced have been discussed in a previous paper.While it is admitted that the conditions prevailing through this work differ' in some respects from those of industrial rolling practice, it is felt that many of the factors investigated have an important practical significance. Some of the work described forms a continuation of the researches of R. S. Russell (2) , (3) , (4), into the recrystallization of various pure leads after deformation by rolling.MATERIALS USEDIn this work, a variety of "pure" leads and certain dilute alloys made from the purest of the basis leads have been studied. The compositions of the basis leads and the corres...

Jan 1, 1940

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By L R. Marshall, M J. Rubenach, T G. Blenkinsop, J S. Cleverley

The source and transport regions of fluidised (transported) breccias outcrop in the Cloncurry Fe-oxide-Cu-Au district, providing insights into the origins of other fluidised magmatic-hydrothermal breccias such as kimberlites. Discordant dikes and pipes with rounded clasts of metasedimentary calc-silicate rocks and minor felsic and mafic intrusions extend several kilometres upwards and outwards from the contact aureole of the 1530 Ma Williams Batholith into overlying schists and amphibolites. The brecciation initiated at depths >10 km and may have resulted in surface breaching. We used analytical equations for particle transport to estimate clast velocities (eÆ 20 ms-1), approaching volcanic ejecta rates (up to 80 ms-1). The wide range of CO2 fluid inclusion densities (up to 150 MPa), the localisation of the base of the breccias in contact aureoles, and the scale and discordancy of the bodies suggests the breccia transport process was triggered by an abrupt release of overpressured fluid. At these depths, such extreme behaviour may have been achieved by release of dissolved fluids from crystallising magma, in combination with a strongly fractured and fluid-laden source, sitting under a strong, low permeability barrier, and such parameters may be analogous to the asthenosphere/lithosphere boundary in the case of kimberlite initiation. The relationship of these breccias to the Ernest Henry iron-oxide-Cu-Au deposit suggests they may have been either fertile or æfailedÆ orebody feeders.

Jan 1, 2005

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

By Vaughan J. P

The Pegmont deposit is a stratiform Pb-Zn sulphide body occurring in a thin, iron-rich metasedimentary unit situated near the top of the Kuridala Formation, a part of the Mary Kathleen Group of the Middle Proterozoic"Eastern Geosyncline" succession of the Mount Isa-Cloncurry district. The deposit appears to have developed in a shallow basin or depression on a sea or lake floor.Detailed chemical and mineralogical study of seven diamond drill cores through the ore horizon shows that in addition to galena and sphalerite the orebody contains a large range of iron-rich silicates and aluminosilicates.Further, five drill cores selected to represent a section from basin centre to basin edge exhibit clear and systematic chemical and mineralogical changes in the ore horizon in both a vertical and, most importantly, ill a lateral sense.Reconstruction of the sedimentary environment of the ore horizon as a whole shows this to be a silicate facies of a phosphatic, manganiferous iron formation or, more accurately, of "ironstone" in the sense of James (1966, U.S. Geol. Surv. Prof. Paper 440, chapter W).On the basis of both mineralogy and chemistry this silicate facies may be subdivided into three microfacies according to the dominant iron silicates characteristic of each: a fayalite microfacies, a hornblende-clinopyroxenemicrofacies, and a garnet microfacies. Significant Pb-Zn sulphide concentrations are confined almost entirely to the fayalite microfacies.

Jan 1, 1979

By H Bibby

Initial analysis of Long Offset Time Domain Electromagnetic (LOTEM) data has traditionally been made in terms of early and late time apparent resistivities. By using more than one grounded bipole as a source, a tensor analysis technique analogous to the method used to analyse DC resistivity multiple-source bipole-dipole surveying may be formulated. We define the æinstantaneous apparent resistivity tensorÆ as the tensor that relates the total electric field vectors at each instant to the steady state (DC) uniform half space current density vectors due to each source. Instantaneous apparent resistivity tensors calculated for a 3D resistivity model suggest that profiles of LOTEM measurements across simple 3D structures can be used to create an image that reproduces the main features of the subsurface resistivity. Where measurements are distributed over an area, maps of the tensor invariants or the tensor ellipses at different times can be made into a sequence of images which provide a way of ætime slicingÆ down through the target structure.

Jan 1, 1996

Lower greenschist quartzo-feldspathic schists within the N-S trending Earnslaw Synform of the Upper Wakatipu area are pervaded by late-stage quartz filled extensional and extensional shear fractures, with quartz-scheelite lodes infilling normal faults. Exposed veins/lodes mapped over at least 1000 km2 define a paleoflow system developed during late metamorphic exhumation of the schist. Both veins and lodes have consistent angular relationships to the schist foliation independent of their location on the Earnslaw synform. Unfolding the synform leads to a regional subhorizontal foliation and a systematic set of subvertical quartz veins striking NNW extending over a depth interval >5 km, striking parallel to a set of normal faults hosting the quartz-scheelite lodes. The structures define an extensional regime with s1 sub-vertical, s3 oriented WSW-ENE, a low differential stress, and suprahydrostatic fluid pressures.   The quartz-scheelite lodes (<2 m thick) occupy faults which cross-cut the quartz veins, and are traceable for a few hundred metres, at most. The lodes consist of laminated and/or massive quartz, slivers of crushed and folded schist, random and discontinuous lenses of scheelite with clay selvages separating the lode from relatively undisturbed wallrock schist. Textural evidence suggests that slip developed incrementally with total displacement on faults during lode formation on the order of a few ten's of metres.   The distribution of Glenorchy veins demonstrates broad scale hydrothermal flow through low-permeability schist, channelled within dilatant mesh style structures comprising interconnected shear and extension fractures. Flow through the lodes was likely derived from the greater surrounding area via the interlinked network of fractures and focused into the low displacement shears. Available evidence suggests the system developed together in a uniform extensional stress regime toward the bottom half of the seismogenic regime.

Jan 1, 2001