Search Documents

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

By Miller RJ, Eager DT, Lama RD

For safe and efficient mining operations, it is essential that environment and equipment status be monitored. A system that gives quick access to status at any given time, and also permits quick analysis of their history, is required. Such a computer based monitoring system has been installed at West Cliff Colliery.The system is based on 2 super mini computers. Three major sub-systems monitor conditions in the longwall operations, environmental conditions in the intake and return roadways, status of the underground and surface installations, and mining and transport equipment.

Jan 1, 1985

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By Hewitt D

A study of two laterite profiles developed on a serpentinite near Rockhampton, shows that loss of Si02 and MgO results in the relative concentration of Fe203, A1203 and a number of minor elements. Serpentine is broken down to form montmorillonite, goethite, quartz and kaolinite. Enrichment of nickel occurs, and it is shown that the element is mainly associated with montmorillonite and serpentine. Highest nickel values are associated with a zone in the profile which occurs at a depth of 10.5-22 metres, and the bulk of the nickel in this zone (42-80%) is associated with the

Jan 1, 1974

By W A. van der Westhuizen

Selective mining played a major role in saving a mine and a communityÆs existence as well as creating a working culture that is the model for all KumbaÆs mines. The successes that resulted from selective mining led to receiving KumbaÆs highest award (it was the Gold Medal Breakthrough project of 2003) as well as the productivity award at the National Productivity Institute award ceremony in 2004. Kumba was established in November 2001 (previously Iscor Mining). The new company identified Mineral Resource Management (MRM) as one of its key drivers and an initiative was launched to define MRM in the Kumba way. Best MRM practices at the Kumba mines were included in the definition. Selective mining was born out of this initiative. One of the key principles of good MRM practice was identified as: æThere must be a balance in the operational processÆ. This principle was applied with great success at Thabazimbi Iron Ore mine in the Limpopo province, South Africa. The emphasis of this paper will be to show how value can be unlocked throughout the whole mining value chain. In the past (up to 2001) the mine went through a number of crisis situations: planned production performances were not reached, the stripping ratio was extremely high with two new pits, the product beds were not of constant quality, slope failures were big risks, flooding could and did cut off half of the ore supply, and restructuring demoralised staff.This paper focuses on: selective mining throughput drivers, and selective mining and its role in achieving this balance.The results were dramatic, with huge improvements in production results, stockpiles, plant yields and product bed specifications. The mine was brought into balance and a self feeding loop was created with positive spin-offs up to this day.

Jan 1, 2005

Portfolio management tends to separate the functions of Asset Allocation and Stock Selection, so the person responsible for reviewing an expert's report on a company would typically be choosing between companies rather than between a company and cash or bonds. How these choices are made depends on the investment time horizon, philosophy and style. Two styles, momentum investing and value investing are contrasted and the role of valuation methods within the framework of each style is evaluated. Finally, pricing is distinguished from valuation.

Jan 1, 1994

Completing its historical role the opera tion of copper blast furnace of the Saganoseki Smelter was terminated in 1970, but it left some interesting data on metal lumps formed at the furnace bottom. Analysis disclosed the lumps to be speiss containing 100 to 10,000 g/t of Au and Ag and stratified to iron speiss and copper speiss. Solidifying temperatures of iron speiss and copper speiss being approximately 1,090¦C and 800¦C respectively, copper speiss precipitated at the lower side. The distribution coefficient of Au and Ag between matte and speiss (g/t Au(Ag) in matte / g/t Au(Ag) in speiss) is in the range of 1 x 10 2 to 2 x 10 ' and 1 x 10 1 to 5 respectively. The higher Cu % is in speiss, the-more An and Ag are distributed into speiss. Except for a few data, these results comfotm well to the range of distribution equilibria of Au and Ag in matte and speiss systems by Gerlach and Others.

Jan 1, 1980

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

By Foudoulis C, Smith CB, Drew RM, Sun S-S, Sheraton JW, Hall AE

Primay (syngenetic and protogenetic) inclusions - i.e. minerals formed during or before diamond growth and encapsulated in the diamond - provide important information on the origin of diamond. Recent Rb-Sr and Sm-Nd dating of such inclusions has yielded crystallization ages older than their volcanic host, implying that diamonds are mantle xenocrysts. In this paper we report results of studies on the nature of syngenetic inclusions and the carbon isotopic compositons of the host diamond from the West Australian diamond deposits at Argyle and Elllendale. The Argyle diamonds are dominantly, of eclogitic paragensis and are characterized by strongly C depleted compositions. We have recognized an association of stone morphology, inclusion type and carbon isotopic composition amongst the Argyle stones, and on the

Jan 1, 1989

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation: W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By Murdaugh W

The application of photogeological techniques and analysis of more advanced remote sensor images can be a cost and time effective tool in the search for desert placer gold deposits. Examples are given of regional analysis using standard false color composit Landsat images and conventional black and white aerial photography. The examples include identification of sites to sample to evaluate the pathways of .alluvial gold migration and identification of potential sites of concentration. The results of these studies developed an increased number of target areas and exploration in proceeding with promising results. In addition to the development of additional target concepts and identification of specific target areas data useful to evaluation of mineability can also be obtained from photogeological investigation. Some indication at least can be obtained of the existence of duricrusts and salines that may hamper mining. Identification of possible sources of water is another important task in the desert environment. In addition indications of the clay content of the material to be worked is very important because of its economic impact on operational costs and overall recovery. The application of photogeology to these questions is discussed.

Jan 1, 1988