Search Documents

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

Study on Influence that Styrene-Phosphoric has on the Surface Property of Rutile Minerals

Sep 13, 2010

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

Investigation on Multicomponent Semi-Autogenous Grinding

Sep 13, 2010

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

This study explores two evolving 3D surveying technologies, photogrammetry and laser scanning, and applies them to deformation monitoring of rock faces and mine highwalls. A quantitative analysis focused on 3D coordinate determination is performed. Furthermore, a qualitative assessment directed at the practicality and viability of each system operating near a rock face or in a mining operation is undertaken to reveal one systemÆs deficiencies over the other. Two photogrammetric and four laser scanning surveys aimed at optimising accuracy and precision within a short period of data acquisition are conducted on the rock face at Organ Pipes National Park, Keilor, Victoria. The accuracy and repeatability of each survey is determined using a combination of iWitness photogrammetric, and Cyclone laser scanning software. The 3D coordinates of targets placed on the rock face are determined by triangulation and resection principles within a bundle adjustment. The coordinates determined by each system are then compared in a 3D transformation. Controlled deformation conditions are established to determine the precision to which each system can detect movement in the rock face. An object of known dimensions is placed on the rock face to simulate deformation. The relative orientation of images taken for the pre- and post-deformation photogrammetric surveys provide an overall 3D point accuracy of 1.255 mm and 1.804 mm respectively. A 3D transformation shows discrepancies of less than ¦22 mm (RMS) between the geometry of the photogrammetric and laser scanning models. Both systems are able to detect the simulated deformation to a precision of 50 mm. This work also identifies how to obtain millimetre accuracy for 3D coordinate determination of rock faces, thereby providing a quality data set for surveyors, geotechnical engineers and mine geologists. Photogrammetry is shown to be a mobile, time and cost-effective technique that is more amenable to mining operations than terrestrial laser scanning. However, both systems demonstrate that they are capable of detecting movements that may lead to failures in the rock face, and possibly endangering human life. The implications are significant for surveyors, geotechnical engineers and mine geologists working in mining operations where enhanced safety conditions, increased productivity and lower operational costs are important considerations.

Jan 1, 2009

Failure of rock materials is a process of crack propagation. Crack initiation takes place when the crack tip stress intensity K reaches a critical value called fracture toughness, K1C. The rock fracture toughness is known to be affected by the surrounding environment such as temperature, confining pressure and humidity. In order to examine the effect of humidity, a series of semi-circular bend tests were performed under various water vapour pressures in a rock material that is known to be anisotropic. Water vapour promotes stress corrosion of rock and therefore the fracture toughness was found to have a decreasing trend with increasing water vapour pressure. The rate of decreasing the fracture toughness depends on the microcrack density that promotes the migration of water vapour into the rock. Also in an anisotropic rock, the fracture toughness depends on the direction of crack in relation to the anisotropy of the rock material.

Dec 6, 2010

By J Merrells

Fluor, together with our clients, has yielded significant reductions in the total cost of mining projects by employing a systematic and methodical process of cost reduction. This paper outlines this structured approach to reducing the total cost of projects through the gathering of information, the evaluation of the zero base design, and the development of the execution strategy for the project in the study phase.Over the recent iron ore boom the cost of growth projects escalated rapidly due to a variety of factors including the engineering cost of re-designing facilities, construction in remote areas and an increase in the ‘perceived’ capital requirements for maintainable and operable facilities.Fluor has made strategic steps towards safely reducing the capital intensity of projects, by working with clients to develop zero base designs which utilise the minimum technical requirements in order to meet the function of the plant and then add cost for safety, maintenance and operability only where clearly justified.This paper has set forth a structured three phased approach to focus the team on reducing capital cost while maintaining a low increase in engineering effort.The initial ‘gather’ phase focuses the team on acquiring information and identifying decisions that will need to be made so that the team can prioritise and focus the attention on areas that will provide the greatest benefit. Within this phase the identification of zero base design requirements, review of lessons learnt and analysis of capital cost levers, allows the team to identify the key decisions on the project that will affect the capital cost.In the subsequent ‘evaluation’ phase the team established the zero base design, using the hierarchy of cost reduction as a guide to focusing the team’s attention on high yielding cost saving opportunities.In the final phase the team develops the execution strategy which will yield the least cost using strategies and tools such as modularisation, standardisation, replication, strategic sourcing and 3D design.CITATION:Merrells, J, 2017. Reducing total project cost in the study phase using zero base design, in Proceedings Iron Ore 2017, pp 621–626 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

A Robust Chemically Enhanced Electrostatic Separation Technology Physical separation processes such as gravity, magnetic and electrostatic separations are extensively used in heavy minerals separations. Electrostatic (aka High-Tension) separation facilitated by the conductivity differences, in particular, is used for separating rutile from zircon. Although electrostatic separation is effective, it is not efficient. It suffers from separation efficacy issues owing to sensitive variables such as humidity, surface contamination, particle sizes and the temperature of the feed and other equipment parameters. The variations in the process conditions especially with humidity, temperature of the feed and the mineralogy and surface impurities can cause significant reduction in the separation resulting in production rate losses and product quality issues. Cytec Industries has developed chemical enhancement technologies for electrostatic separation for rutile -zircon separation from the heavy minerals. The major advantage of our technology is its higher separation efficacy in the first pass, substantial energy savings and most importantly its ability to do separation at room temperatures. The bolt-on nature to the existing electrostatic also an added feature that reduces the capital expenditure significantly. The separation efficiency between rutile and zircon was increased as much as 8 - 11 per cent compared to control. It is possible to extend the chemical enhancer technology to problematic feeds and other mineral systems that are not easily amenable to conventional electrostatic separation.

Sep 13, 2010

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia. As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary. The works are situated at Port Kembla (New South Wales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. This will mean: a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operation...

Jan 1, 1910

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

A substantial proportion of current and historic West Coast gold production comes from deposits situated around the margins of æice ageÆ glaciers. Gold has been eroded and transported by glacial ice then deposited in till and outwash gravel. The interplay between fluvial and glacial processes, climate, basement geology, tectonic uplift, sediment supply and sea level dictates many aspects of the development of the West Coast landscape. The way in which the external forcing factors interact is crucial in determining the gold content of placer deposits in this region. The following is an outline of some of the factors that influence the gold distribution in vicinity of glacial margins.

Jan 1, 2000

By N Stoitis, L Lien, B Tapley

The treatment of hypersaline waters originating from numerous gold projects within the Western Australian Goldfields region via membrane technology has been assessed. A combination of Ultra-filtration (UF) and Nano-filtration (NF) using Ecotechnol’s modified elements effectively removes the polyvalent ions responsible for the high lime and cyanide consumption as well as the prevalence of scale formation characteristic of gold operations in this region. Through removing up to 98% magnesium, 94% calcium and 99.7% sulfates from hypersaline water with total dissolved solids from 40,000mg/L to 250,000mg/L, Ecotechnol and subsequent independent tests have demonstrated up to an 87% reduction in lime consumption and through the ability to increase the operating leach pH, reduce cyanide consumption by up to 28%.CITATION:Tapley, B, Stoitis, N and Lien, L, 2015. Modified nano-filtration membrane treatment of hyper-saline goldfields water – an overview and benefits to gold plant operation and economics, in Proceedings MetPlant 2015, pp 431–463 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Mann V. I

The Mount Isa property has been in operation since June, 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods.Stoping methods have been designed to apply to parallel lodes ranging from 10 ft. to over 100 ft. in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sub-level stoping method for mining the sulphide ores.

Jan 1, 1938

The stratigraphy of the Western Coalfield is briefly reviewed and the important units of the Lithgow Coal Measures, particularly the coal seams, are defined. The possibility of coal measures of Tomago age ocurring near the edges of the Sydney Basin is discussed onpresent evidence.Using data obtained from unpublished drilling records, detailed structural, isopachous and lithofaeies maps have been drawn. These show that the structure of the coal basin has been influenced by the underlying basement in many ways.The prominent jointing in the overlying Triassic sandstones is discussed in relation to jointing in the coal measure sediments.It is concluded that in addition to the general knowledge obtained with respect to the coal basin, useful information regarding coal quality and quantity can be gained by the study of broader sedimentary and structural features.INTRODUCTIONThe term "Western Coalfield" covers approximately the area from Katoomba to Rylstone, together with the smaller, separate Ulan area (Fig. 1). The area studied is part of the great sedimentary Sydney basin named by Osborne (1948). The first discovery of coal in Sitlt in the area was made in 1824 by Andrew Brown, although George Bass noted the presence of coal float in the Grose River in 1797. Production is recorded from the Western Coalfield in 1838 but mining was intermittent until 1868 when mines in the Lithgowvalley (producing coal from the Lithgow Seam) came into production. In 1882 the Katoomba Seam was first worked at Katoomba.The work of J. E. Carne (1903, 1908) defined the limits of the Coal Measure sediments and also contributed a great amount of valuable detailed information about the region.

Jan 1, 1960

In coal mining, geophysical techniques have an established application in determining the location of seam boundaries ahead of the face so that underground mines can be planned to avoid any geological structures that might disrupt production. Geophysics can also be used in geotechnical studies to determine the in situ properties of the rock mass and the response of the rock mass to the mining. The use of geophysical logs and microseismic monitoring in these geotechnical applications are discussed in this paper.

Jan 1, 2002

Determination of Flotation Kinetics of Coal Grain Types in a Pilot Scale Jameson Cell using Coal Grain Analysis Method

Sep 13, 2010

By Paterson R. G, Compston W

The Mine granite at the Ardlethan tinfield is dated by Rb-Sr on a muscovite concentrate at not less than 417 ± 2.5 Ma (2s), consistent with the intrusion of this granitic body into folded Late Ordovician sediments. A combination of Rb-Sr and K-Ar evidence suggests a slightly younger age, 41O ± 2.5 Ma, both for the neighbouring Ardlethan Granite and for the hydrothermal alteration of the Mine granite, with which the tin is associated.On this basis, the somewhat high 206Pb/204Pb of two galena samples from within the hydrothermal alteration zone is best explained by an increase in U/Pb of order 10 per cent during a geochemical event in the Late Precambrian, in the rocks which eventually yielded the Pb to the mineralising fluid. This earlier event probably increased Th/U in these rocks as well, by as much as 5 per cent. If these reconstructions are valid, the lower-than-average U/Pb implied for the original Precambrian source rock bespeaks a mantle component of marginally greater proportion than for "average orogene".

Jan 1, 1982

By C A. Locke, M Stevens, P Vidanovich, J Cassidy, J L. Mauk

The Karangahake adularia-sericite epithermal gold-silver deposit, located at the southern end of the Waitekauri Corridor, Hauraki Goldfield, occurs as quartz veins with associated alteration haloes. Integrated geophysical studies were undertaken to determine the expression, location, and extent of these alteration zones. Aeromagnetic data show an extensive, magnetic æquietÆ zone over Karangahake and the southern Rahu Ridge that represents a zone of magnetite destruction resulting from hydrothermal alteration. Analytic signal data are used to define the boundary of this zone; the resulting 6 km2 area is elongate north-south with an irregular boundary. A detailed gravity survey over the area reveals a positive residual gravity anomaly, up to 30 gu in amplitude, over the Karangahake deposit. Density measurements on near-surface rocks give low values indicating that the source of this positive gravity anomaly must be deep; possible causative bodies include an igneous intrusion or dense sulfide mineralisation. To the west and east of the host Waipupu Formation, strong gravity gradients of 100 gu/km and 65 gu/km reflect the faulted boundary of the Hauraki Rift, and the edge of the Waihi Basin respectively. High resolution airborne radiometric data define a 2.2 km2 area of potassium enrichment. This area is elongate north-south and has an irregular boundary. It coincides approximately with the centre of the magnetic quiet zone and the peak of the gravity high, and correlates with known areas of intense mineralisation. Anomalously high potassium counts and elevated K/Th ratios correlate with areas of potassic alteration that have undergone K-metasomatism. Underexplored portions of this zone may indicate areas of gold-silver prospectivity. Combined geophysical data therefore reveal the extent of hydrothermal alteration, and the central zone of Kmetasomatism that is most likely to contain orebodies.

Jan 1, 2005