Search Documents

By T. E. Watkins, M. D. Nelson

A method of determining the lime content of drilling muds proposed by Battle and Chaney* has been examined both in the Field Research Laboratories of Magnolia Petroleum Co. and in field drilling operations. This proposed analytical method is condensed as follows: Titrate one ml of mud and one ml of mud filtrate, each with 0.02 N H2SO4, to the end point with phenolphthalein. The volume of acid in ml required for the mud titration is recorded as Pm and that of the mud filtrate titration as Pf Calculation of the lb lime/bbl mud is accomplished by use of the formula, lb lime/bbl mud = 0.6 (Pm - 1.3Pf) - 0.6 The analytical procedure outlined by Battle and Chaney was found to be quite satisfactory when reasonable precautions are used in mud sampling technique. Calculation of lime concentration by the method proposed in the above publication, however, has given values that varied as much as 100 per cent from the known lime content, for muds of either high or low solids concentration. By use of a formula, lb lime/bbl mud = 0.26 (Pm-F1.Pf), based on chemical equivalents of acid required for titration, both laboratory and field data have been satisfactorily correlated with the known amounts of lime present in the muds. In this formula a correction, F1, or volume fraction of liquid in the mud, is made for the solid content of the mud. Pm and Pf * Paper on "Lime Base Muds," presented by J. L. Battle (Humble Oil and Refining Co., Houston, Tex., and P. E. Chaney (Sun Oil Co., Beaumont Tex.), at the 1949 Spring Meeting of the Southwestern District API Division of Production, Dallas, Tex. The analytical procedure has also had wide distribution in a trade journal, Kembreak, published by the Accuracy Rig and Tool Co., Houston, Tex, †Derivation of equation lb/bbl — grams/350 ml 1 ml 0,02 N acid = 0.000741 grams of lime 1 ml 0.02 N acid/ml lime suspension = 0.26 lb of lime bbl lb of lime/bbl = 0.26 (Pm -F1, Pf ) have the same significance as in the Battle and Chaney equation. Table I shows typical data employing both formulas in calculating the lime content of various lime muds. This suggested procedure ignores lime which is in solution in the mud. The solubility of lime in water, normally about 0.5 lb per bbl, is greatly decreased by the addition of caustic soda, and, in a lime mud, it is probable that the concentration of dissolved lime is of the order of 0.1 lb per bbl. Such an amount of lime can be ignored, since it is within the range of accuracy of the method.

Jan 1, 1950

Jan 1, 1968

By J. L. Gillson

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

Jan 1, 1970

Discussion of "The Ordering Transformation in Titanium-Aluminum Alloys Containing up to 25 at. pct Aluminum" by F. A. Crossley, Trans, TMS-AIME, 1968, vol. 242, pp. 726-30. Dr. Blackburn, in his response, pointed out that the c/a ratio of the Ti-26 at. pct A1 alloy quenched from 900°C is 1.6006 and not 1.5965 as plotted in Fig. 19. An error in transcription was made in preparing Table V of Ref. 1 (F. A. Crossley, Trans. TMS-AIME, 1966, vol. 236, p. 1174). The corrected Fig. 19 strengthens rather than weakens the argument that a martensitic transformation occurs in alloys containing from 15 to 18 at. pct Al. A Study of the Factors Which Influence the Rate Minimum Phenomenon During Magnetite Reduction, by P. K. Strangway and H. U. Ross, Trans. TMS-AIME, 1968, vol. 242, pp. 1981-88. Page 1883 Reverse Figs. 5 and 6. Sigma—Its Occurrence, Effect, and Control in Nickel-Base Superalloys, by J. R. Mihalisin, C. G. Bieber, and R. T. Grant, Trans. TMS-AIME, 1968, vol. 242, pp. 2399-2414. Pages 2403, 2407, and 2414 Arrows should appear on Figs. 4 and 9; a sigma is missing from Table IV; line 2, page 2414, change "case" to "cast". These are published correctly in the bound volume. Index, December Issue There were a few omissions in the Author Index. These have been corrected and published properly in the bound volume.

Jan 1, 1970

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By Cleland N. Conwell

Coals are found in all parts of Alaska, ranging in geologic age from Carboniferous to Tertiary, and grading from lignite through anthracite. Only the Matanuska and Nenana coal fields have been extensively developed. Nenana Field Today roughly 94% of the coal mined in Alaska comes from the Nenana field near Healy. The coal-bearing horizons in the Nenana field are found in a sedimentary sequence of Tertiary age approximately 2800 ft in thickness. The sediments rest directly on schists of possible Precambrian age. Individual coal beds in the field have been designated by both letters and numbers, starting with the alphabetical designations from A to G, and the numbers 1 to 6. Of these coals, the principal beds that are mined are F, 1, 2, and 3. These vary greatly in thickness, e.g., bed 1 ranges to over 50 ft, and beds 2 and 3 to 30-40 ft.

Jan 10, 1972

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting Cu, Ni, Co, and S from high grade Ni concentrate produced from Lynn Lake ores and describes in some detail the chemistry of the process. In the leaching stage air, ammonia, and sulphide minerals react in a sequence of inter-related steps to produce soluble amines of Ni, Cu, and Co in a solution containing sulphate, thiosulphate, polythionate, and sulphamate ions and a controlled amount of free ammonia, the iron and other components of the concentrate remaining as an insoluble residue which is separated from the leach solution by filtration. The pregnant solution produced in leaching is further treated by boiling to precipitate and remove Cu as cuprous sulphide, leaving a copper-free solution with a composition suitable for subsequent precipitation of Ni and Cu by H,

Jan 3, 1955

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 36. Experienced copper metallurgist and mining geologist. Familiar also, through 15 years' broad practical experience, with mining, cyanidation, concentration (including oil flotation), metallurgical accounting, and mine and plant management. Best references. No. 237. Member, graduate engineer with 10 years' experience in malleable, gray -Iron, and steel, as chemist., metallographist, and metallurgist. Researches and investigations by laboratory methods and under works conditions. No objection to some routine. No. 243. Member, technical graduate, broad experience in coal, oil, and clay. Will go anywhere as mining geologist after Sept. 1, 1915. No. 244. Member, technical graduate, aged 30, married, with over 10 years' experience as chemist, engineer on construction, superintendent and general superintendent of bituminous coal and coke plants. SpeaksSpanish. References. No. 245. Member, open for engagement as mine safety inspector or as superintendent of bituminous coal mine. No. 246. Member, graduate mining engineer, with five years' experience in coal mining as mining engineer, construction engineer, pit boss, and superintendent, open for engagement. Best references. No. 247.

Jan 9, 1915

By Ivan E. Goodner, Charles H. Fulton

THE subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,1 Bolles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the sulphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to date no effort has been made to correlate the data obtained in the latter researches and apply then to the study of the product called " matte," which is made in such large quantities by copper and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections I. A review and discussion of the various binary systems of the metallic, sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical and chemical properties of these sulphides. II. A description of the results obtained from the chemical and metallographic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Nov 1, 1908

Texture Transition in Ordered CuAu, by E. A. Starke, Jr., J. C. Ogle, and C. J. Sparks, Jr., Trans. TMS-AIME, 1969, vol. 245, pp. 169-70. pole figures should have had two parts not one. On the Estimation of Oxygen Absorption by Continuous Molten Metal Streams, by J. Szekely, Trans. TMS-AIME, 1969, vol. 245, pp. 341-44.

Jan 1, 1970

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

Jan 1, 1967

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

Jan 1, 1967

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935