Search Documents

By Calvin J. Konya

Overloaded blastholes and insufficient stemming are major factors in flyrock accidents at surface metal and non-metal mines, Accurate measurement of blasthole depth, stemming height, and water depth would reduce the overload and the probability of blow-out, flyrock, excessive ground vibration, and airblast. Problems result because current measuring systems are inaccurate and often difficult to used A literature survey determined measurement techniques and blasting parameters prior to 1970. Similar data were gathered for current practices in 11 iron mines, 30 copper mines, and 92 quarries. Most operations used a cloth tape to measure borehole depth and stemming height; approximately 10% of the operations had dry blastholes. Alternate measurement techniques were evaluated and discussed. Candidate measuring techniques with best potential for improvement over the present weighted tape method are disposable tapes or string chains, automated readout tapes, modified sludge level indicators and acoustic resonance methods.

Jan 1, 1981

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By M. B. Haggerty, Joe Welna

The Minnesota Department of Transportation is constructing a stormwater storage facility (SSF) along Interstate 35W (I35W) south of downtown Minneapolis, MN. The project will provide storm surge capacity reducing the frequency with which major precipitation events result in flooding of I35W. The design consists of six, 42-foot diameter, 90-foot deep, adjacent underground shafts providing 14.7-acre feet of storage. Construction challenges include high groundwater with variable glacial outwash deposits. Constructability and ground variability were managed using construction manager general contractor (CMGC) project delivery. CMGC provides an environment for collaboration and innovation starting in the design phase and carrying through construction. This paper provides an overview of key efficiencies and collaboration examples implemented on the I35WSSF project which were aided by CMGC delivery.

Jun 13, 2023

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By Karl J. C. Harries

"5.1. INTRODUCTIONThis chapter is intended as a general overview of the subject of royalties between private parties – royalties extracted by governments are not dealt with. This same subject is covered in detail in Volume II, which critiques many sample provisions taken from agreements, giving both pros and cons. If you find something that interests you in this chapter, check Volume II for extra information. Detailed cross-referencing to Volume II has not been attempted, however, most subjects mentioned in this Chapter will also appear in Volume II, usually in greater detail. Reference should be made to the Index.A Brief History of Royalties1In the early days of mining in Canada, the tendency was to sell a claim for cash and to move on, using the stake to look for and stake more prospects. As prospectors became more sophisticated and Canada’s North opened up, the market for properties and the number of mining properties available increased dramatically. Speculation and the practice of consolidating several small properties into one large holding entity became common. In “hot” areas, the speculators2 could far outnumber the prospectors, many of the former having little or no prospecting expertise but lots of market and promotional savvy. However, to consolidate a number of small parcels into one large project can be expensive, and many of the parcel owners became interested in keeping a share in the project, rather than giving up everything. Speculators who were trying to consolidate small parcels wanted to minimize cash payments to parcel holders (usually they did not have much cash and preferred it flowing in their direction rather than away from them). Accordingly, non-cash transactions were developed to meet the aspirations of both owners and speculators."

Jan 1, 2003

By R. Minnitt, C. Morgan, D. Fourie

The problems associated with outliers and their adverse effects on resource estimation in deep level South African gold mines are presented, and solutions suggested in available literature are reviewed. Traditional Witwatersrand type outlier capping uses the 99th percentile grade as the upper limit, a somewhat blunt approach. The occurrence of high and low grade areas in mining operations and the estimation of resources using geostatistical techniques require that the assumption of stationarity be upheld. Honouring the stationarity of data requires that mining areas be subdivided into appropriately sized and spaced domains. In order to overcome high-grade conditionally biased block estimates, the overly strong influence of extreme grades is mitigated by using naturally occurring grade sub-domains, by identifying outliers within the grade sub-domains, allocating relevant capping limits, and weighting them in a post-estimation process to. Rather than applying a capping value across a domain it applies a maximum cap based on the extreme value and its range of influence; the method also ensures that relevant capping occurs even in lower grade sub-domains. The proposed method for capping outliers recognises that metal contained in high grade chip samples should not be over-capped, and based on the grade of surrounding samples. The post-processing method of capping outliers does not interfere with the kriging equations. The method is simple, elegant, and can be easily applied. An advantage is that the output from the kriging process is not overwritten, allowing for comparison between original kriging results and post-processing results.

Sep 1, 2021

By N. A. Smith, R. J. Fowell, J. L. Hislam

Abstract: Data are presented from two sites in southeast England, where problems were encountered in tunnelling through ground containing flint. In response to the difficulties, substantial laboratory testing programmes were initiated to determine the strength of the flints.It is shown that the strength varies very considerably, even within a single flint particle and that the practice of estimating unconfined compressive strength by a single multiplier applied to the point load strength index (Is(50)) may give misleading results. The preparation of UCS specimens for testing was found to be very difficult and it is recommended that tunnel machine capacity is assessed relative to Is(50). Résumé: Des données sont presentées sur deux sites dans le sud-ouest de l’Angleterre,où le perçage d’un tunnel dans un sol contenant du silex a posé des problémes. En consequences de ces difficultés, des programmes substatiels de recherché en laboratoire ont été initiés afin de déterminer la resistance des silex. Il est demontré que la resistance varie considérablement, même au sein d’une particule de silex, et que la pratique de estimation de la résistance en compression non confinée, (UCS) par le biais d’un simple coefficient appliqué au ‘point load strength index (Is50)’ pourrait donner des resultants trompeurs. La préparation de specimens UCS destinés aux tests s’est avérée trés difficile et il est recommandé que la capacité de la machine de perçage de tunnels soit calculée relativement au Is50. Zusammenfassung: Daten von zwei Standorten in Südosten von England, wo Probleme beim Tunnelbau durch feuersteinhaltigen Grund antraffen, sind angegeben. Wegen diesen Schwierigkeiten wurden Laboratoriumsforschungsprogramme eingeleitet, um die Festigkeit von Feuersteinen zu bestimmen. Es wurde gefunden, dass die Festigkeit sehr unterschiedlich war, selbst bei einzelnen Feuersteinstücken, und dass die Praxis, die unbegrenzte Kompressionsfestigkeit (uKf) auf Grund eines einzigen Multiplikationsfaktors vom Punktladefestigkeitsindex (Is50) abzuschätzen, zu irreführenden Resultaten führt. Die Vorbereitung der uKf Prüfstücke war sehr schwierig und es wird vorgeschlagen, dass die Kapazität der Tunnelbaumaschine in Abhang der Is50 bestimmt wird.

Jan 1, 2003

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps,

Jan 1, 1964

The following paper outlines the types of employment immediately available to graduates following their university degree, a discussion on mine manager requirements, mentions career advancement and time frames to achieve this as well as providing some key information regarding student vacation work. The author hopes to educate present graduates, as well as inform students of characteristics to develop the most opportunities in life.

Jan 1, 2006

By Shahé Shnorhokian

Remnant pillars evolve towards the latter stages of mining in an orebody and act as repositories of mining-induced stress. It is therefore crucial to plan ahead as to their dimensions and location with respect to the local geology. A case study of a Canadian base metal mine was examined for the planned mining sequence scenario to identify the stress regimes acting on a future remnant pillar occurring between levels 4800 and 5100, near a brittle dyke. A mine-wide model was constructed in FLAC3D and input parameters included results from field measurements of the direction and magnitude of the principal stresses, and the geomechanical properties of the different formations. Prior to the study, the model was calibrated based on a 6-year record of mining-induced seismicity and rockburst events, focusing on large event clusters. The mining sequence followed at the mine was then used in the model to study the planned future extraction program around the remnant pillar. It is shown that the distance of the remnant pillar from the dyke and another orebody plays an influential role on the stress levels developed in the pillar.

Jun 1, 2012

By Paulo Correa

No processo de implementação de uma nova planta industrial, a disciplina de automação, responde pela integração dos equipamentos de forma a permitir a operação segura e produtiva dos dispositivos envolvidos, com um mínimo de intervenção humana. Em projetos de grande porte, temos muitos fornecedores de equipamentos mecânicos com diversas formas de contratação e estabelecer um padrão único para o sistema de automação, tornase uma atividade complexa, porém, fundamental para o sucesso do projeto. Por outro lado, o sistema de controle é sempre o último a ser montado e pode provocar atrasos no comissionamento dos equipamentos, se não estiver devidamente pronto, ou mesmo ser pressionado para compensar atrasos ocorridos nas etapas anteriores da construção. Nesse contexto, a engenharia de automação precisa estar concluída, os materiais precisam estar disponíveis e a mão de obra pronta para atendimento no exato momento das necessidades. Mediante o uso de uma estratégia de contratação antecipada do pacote de automação, na modalidade MAC, onde apenas uma empresa responde pelo fornecimento global do sistema de automação e instrumentação, reduzindo as interfaces envolvidas, buscando a participação do fornecedor nas fases iniciais da engenharia e com a elaboração de um planejamento consistente de recursos, foi possível atender as demandas da construção e comissionamento, dentro do cronograma e custo previstos para o projeto. Os resultados alcançados pela disciplina de automação e controle, aliados ao resultado global do projeto, sinalizam a assertividade das ações realizadas, trazendo benefícios consideráveis e reduzindo o risco na implementação do projeto P4P.

Aug 16, 2017

By Everton Pizzio

Parafusos utilizados para fixação de partes submetidos a carregamentos cíclicos estão sujeitos a falhas por fadiga. No estudo do conjunto carcaça/corrediça de um compressor fixado por parafusos prisioneiros - ISO M24x3, que fixam o flange da corrediça falharam prematuramente por fadiga. O objetivo deste trabalho é desenvolver uma metodologia para otimizar o desempenho em fadiga do conjunto parafusado. Para tanto, foram realizados ensaios de fadiga visando o melhor processo de fabricação no desempenho em fadiga. Observou-se que o processo de laminação da rosca seguido de tratamento térmico é o mais adequado para o caso em estudo. A conclusão principal foi que a configuração atual de união do flange com a carcaça, resulta num baixo índice de aperto que é verificado através das cargas máximas que são transferidas diretamente ao parafuso e que aumentando o comprimento do parafuso através da inserção de uma bucha extensora, aumenta a vida em fadiga

Aug 17, 2017

By Curtis A. Jones

Continuing interest has been shown in developing processes for extracting nickel and cobalt from low-grade domestic deposits of these metals and in improving existing methods. Of special concern is the nickel-recovery installation at Nicaro, Oriente Province, Cuba, operated for the General Services Administration. The Bureau? of Mines felt that a bibliography would help familiarize personnel at various Bureau of Mines stations and General Services Administration contractors with extraction methods both in the United States and in foreign countries. When this task was under way it became apparent that to compile a complete bibliography would require considerable time, so it was decided to limit the first part to the later literature and issue it independently, thus making it available sooner. The present work supplements the first part and extends the coverage to the earliest years of nickel and cobalt metallurgy.

Jan 1, 1959

By I. G. Gonçalves

For most industrial minerals, the color is directly associated with economic value. In terms of physics, the principal property that defines the term ?color? is the intensity of light reflected (or transmitted) by an object over the visible band, comprehended between 400 and 700 nm. This reflectance spectrum serves as the starting point for a variety of color-describing factors, the most common in the mineral industry being the brightness (TAPPI, 1977 and 1986) and the L*a*b* system (HunterLab, 2008). Quality specifications for mineral products are usually based on these colorimetric parameters. This market is becoming increasingly more selective and demanding over the quality of raw materials and alongside the traditionally controlled characteristics, such as particle size distribution and chemical composition, a trend exists towards the establishment of increasingly more strict specifications for the optical properties of these materials. This is due to the fact that most plants consuming these industrial minerals incorporate them into products in which the visual appearance is controlled. For these plants, most of them being the manufacturers of plastics, paper, paints, and ceramics, variations in the color of mineral materials result in difficulties to achieve the right color in the final product. Therefore, these plants set strict specifications for colorimetric parameters such as whiteness and yellowness, as well as colorimetric coordinates like L*, a*, and b*. For the manufacturer of industrial minerals, this translates into difficulties simply because many of these parameters are usually alien to the tradition of the mining industry. The main quality parameter in the kaolin industry is brightness, which is a weighted average of reflectance values over the range of 400-510 nm (TAPPI, 1977). Due to the lack of a better property, producers tend to use brightness to also assess the quality of the in situ ore and along the processing operations. However, the unprocessed kaolin is often accompanied by ?contaminant? minerals. For Brazilian kaolins, which are the object of this study, the most important contaminants are hematite (Fe2O3), goethite (FeOOH), and anatase (TiO2). Each of these contaminant minerals has a distinct color and behaves differently during the processing of the kaolin ore. Hematite and goethite in particular are particularly strong pigmenting agents and at concentrations as low as 100 ppm they can make the difference between a high-quality white pigment product for paper coating and waste material. As each Fe-bearing contaminant has a different color and responds differently to processing operations (for example, magnetic separation, chemical bleaching, selective flocculation, and/or flotation in the case of kaolin), the in situ brightness tends to show a poor correlation with the brightness of the final product. Brightness measurements are sometimes complemented with X-Ray Fluorescence (XRF) analysis of Fe and Ti, but the total oxide content provided by XRF is also poorly correlated with product quality because Fe may be in the form of goethite, hematite, or inside the crystalline structure of kaolinite. Thus, a more robust technique capable of distinguishing each mineral phase is desirable. Diffuse reflectance spectroscopy has been used to analyze iron oxide/hydroxide content both qualitatively (Torrent and Barrón, 2003; Liu et al., 2011) and quantitatively (Jiet al., 2002 and 2006). These authors correlate slopes and inflection points at characteristic absorption bands with oxide/hydroxide content in natural soils. The approach presented here involves the extensive use of the Kubelka-Munk (K-M) theory, which has been used for color matching (Schabbachet al., 2009 and 2011) and particle size determination (Otsuka, 2004) in a simplified version. Unfortunately, the scattering constant S is very difficult to measure for dry powders, because the equations require a thin layer of material. Attempts have been made (Gonçalves and Petter, 2007, and Gonçalves, 2009) but the experimental errors tend to be high. Thus, this paper aims to develop a tool for the quantification of contaminant minerals in kaolin based on the K-M theory without resorting to measurements over thin layers. This tool is based on a new two-constant approach, which takes into account differences in scattering between materials over the whole measured spectrum. The experimental dataset consists of the reflectance spectra of mixtures between a bleached kaolin and synthetic Fe pigments.

Feb 27, 2013

By George F. Becker

(San Francisco Meeting, October, 1911.) A MERE record of Emmons's professional career would very inadequately represent the man. That he was eminent we know, and our successors will realize in due time; but they must depend upon us for knowledge of a singularly wholesome, modest, unselfish personality, and of a character that did honor to a profession in which trustworthiness is indispensable: Those members of the Institute who met Emmons are his friends, and I never knew one of these who was not the better for that friendship. Emmons was born in Boston, Mar. 29, 1841, the son- of Nathaniel H. and Elizabeth (Wales) Emmons, and was named Samuel Franklin after an ancestor who was of the same family as Benjamin Franklin. He took the degree of Bachelor of Arts at Harvard in 1861, and soon afterwards went abroad to complete his education. From 1862 to 1864 he attended the courses at the École Impériale des Mines at Paris, lie e Beaumont and Daubrée being among his professors. The year 1864-1865 he spent at Freiberg under Cotta and other famous teachers; after which he spent another year in traveling through Europe. Like many other renowned geologists, he approached his ultimate profession from its economic side, and was thus from the first imbued with a sense of high responsibility in the promulgation of scientific opinions or conclusions. With hypotheses which were interesting merely because. they were ingenious or even plausible, he would have nothing to do. In 1867 he joined the Geological Exploration of the Fortieth Parallel at its organization under Clarence King, serving at first as a volunteer, but soon receiving a regular appointment. This expedition was the first one of purely geological character sent out by the United States Government. As Emmons has shown in his admirable presidential address on " The Geology of Government Explorations," its work was founded on a com-

Sep 1, 1911

By Anastasia Xenaki, Edmundo Laporte, Antonio Nieto, Jesus Castillo Gomez, Oscar Velasquez

It is particularly challenging for the mining industry to create and implement an efficient and adaptable mining innovation model to secure the continuous improvement of processes and products via technology. Human resource departments must play a vital role in shifting the mining culture, enabling these new classes of digitally skilled professionals to manage the mining operations of the future. This paper proposes the implementation of a concept based on the 5S mining innovation model ((a) Nieto, 2019), in a coal mining project in Central Asia, Mongolia. Practical and empirical evidence suggests that the model could serve as a roadmap to developing technologies and methods for the mines of the future.

Feb 1, 2023

On Kinetic Coupling in Meso-Scale Phenomena in Mineral Froth Flotation

Sep 13, 2010

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant provides unparalleled ability to ensure safety of the workers, public and environment. Although small spatially, it can vary the airflow from 66,000 acfm to 460,000 acfm. It can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and can be adjusted from the surface if necessary. A ventilation remote monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based-real-time mine ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2002