Search Documents

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985

By Madgwick J. C

A new strain of Thiobacil/us ferrooxidans (SPK I) has been isolated which has a higher copper to iron release ratio (2.04) than the standard T ferrooxidans (CPBI) (1.12). The diminished iron oxidizing ability enables almost quantitative release of copper (93 per cent) from a chalcopyrite-rich concentrate without interference by iron reprecipitation. In a single batch leach, Bougainville copper concentrate yielded 9.3 grams/litre soluble copper from a 4 per cent w/v suspension in 100 days at 32°C.Solvent extraction recovery of soluble copper is recommended as a final step in a leaching process.

Jan 1, 1983

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By Marcelo Sousa de Carvalho

Os aços inoxidáveis possuem uma alta aplicabilidade nas indústrias de petróleo e gás, química e de papel e celulose, principalmente, devido à suas características de alta resistência à corrosão e alta resistência mecânica. Neste trabalho, estudos baseadas na técnica dos cinco punções foram realizados para avaliar as características de conformação do aço inoxidável UNS S32304. A metodologia baseia-se na caracterização mecânica do material para mensurar suas propriedades, como limite de escoamento e índice de anisotropia. Seguiu-se com uma análise teórica da estampabilidade do material através da simulação computacional do ensaio de cinco punções. Esta técnica analisa tipos de deformações desde o estiramento biaxial até o embutimento profundo. Esse trabalho apresenta uma análise computacional do comportamento desse material com relação à estampagem para os diversos punções. É apresentado o gráfico da Razão Limite de Estampagem teórica para o UNS S32304 em relação aos cinco punções utilizados e a influência do coeficiente de anisotropia normal nos resultados.

Aug 16, 2017

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Isabela Costa Mendes Peres

As soldas dissimilares de liga de níquel 182 são utilizadas em usinas nucleares para conectar tubulações de aço inoxidável com componentes fabricados em aço de baixa liga. O procedimento envolvido na soldagem dissimilar pode modificar as propriedades do material, o que afeta diretamente a junta soldada no sentido de aumento da probabilidade de incidência do processo de corrosão. Neste trabalho foi realizado a soldagem dissimilar de corpos de prova dos aços de baixa liga e aço inoxidável austenítico AISI 316L com as ligas de níquel 82 e 182. Estudou-se o comportamento frente à corrosão da junta de solda de liga 182 em ambientes ácidos contendo NaCl e Na2S2O3 empregando-se técnicas eletroquímicas. Ensaios de polarização anódica potenciodinâmica foram utilizados para caracterizar o comportamento de corrosão localizada do material. Os resultados mostraram que o comportamento eletroquímico da junta de solda está relacionado com o aporte térmico e a presença ou não de oxigênio no meio.

Aug 8, 2018

Recovery Efficiency Study on Ilesha Placer Gold Ore by Flotation Using Locally-Sourced Frothers and Collectors

Sep 13, 2010

By F. A. Rutledge, H. Marstraander, J. H. Hulbert, G. A. Apell

"INTRODUCTION The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska caused the Coal Procurement Section of the Alaska Department, U. S. Army, to be established. It proposed to investigate the coal deposits and to expedite production of coal. The Bureau of Mines has closely cooperated in this program and was in direct charge of exploration. As to develop and equip an underground coal mine would have taken time and the need for coal was acute, a deposit that could be prepared for mining quickly was desirable. Several such deposits of stripping coal were known to occur in the Nenana field and were examined by the Bureau. One of these, the Diamond strip mine 4 miles west of Healy, was brought into production late in the fall of 1943. This mine was operated for the Army Coal Procurement Section by the C. F. Lytle Co. and the Green Construction Co.The Roth property, or Leasing Block No. 28, in the Healy Creek Valley offered the largest available tonnage of both stripping coal and total reserves. A program of exploration by the Bureau of Mines was inaugurated in 1943 and completed in 1944. Field parties of the Federal Geological Survey mapped the area had correlated the coal beds during the 1944 and 1945 summer seasons."

Nov 1, 1946

By D. C. Seidel

This report describes generic procedures and equipment arrangements for conducting laboratory-scale hydrometallurgical and related waste-management experiments. It provides a starting point for personnel who have received or are receiving professional training, but do not have specific experience in laboratory procedures. With guidance, it also has application as a resource for technician training. The publication contains chapters on laboratory safety, feed-sample preparation, leaching, solids-liquid separation, and recovery from solution.

Jan 1, 1995

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By Natália de Oliveira Roque Maciel

Nos últimos anos, especialmente fibras naturais extraídos de plantas lignocelulósico, ganharam atenção devido ao seu desempenho como engenharia de reforço compósito polímero. Por exemplo, as fibras lignocelulósicas extraídos a partir das folhas da planta curauá (Ananas acutifolius) exibir um potencial de reforço devido à sua relativamente alta resistência. As fibras, entre 0 a 30% em volume de, foram misturados com resina de poliéster sob pressão num molde metálico, e curada à temperatura ambiente durante 24 horas. Este trabalho procura avaliar a resistência ao impacto deste tipo de matriz de epóxi fibra de reforço. A resistência ao impacto aumentado substancialmente com a quantidade relativa de fibras de curauá reforço do compósito. Este desempenho foi associada com a resistência imposta pelas fibras e o comportamento de propagação da fissura

Aug 17, 2017

"The 34th International Conference on Ground Control in Mining (ICGCM) was held July 28–30 at the Lakeview Golf Resort and Spa in Morgantown, WV. Ground control experts have gathered at this location since 1981 to share ideas and successes for improving designs and technologies to enhance the stability of surface and underground mining operations. Ground control is important to all mining operations but is particularly crucial to underground mining to ensure miner safety and operational viability.The year’s event had 240 registered attendees with 20 pecent of that attendance being from the mining industry. A remarkable number of industry representatives attended given the challenges currently faced by the mining industry. A true testament to the value of the conference, the performance of Tom Barczak and Steve Tadolini as co-chairs and the drawing power of the many exceptional speakers that have attended the annual event for many years.The conference operates under the direction of a board of directors with the cooperation, wisdom and assistance of a large organizing committee. Visit the conference website, www.icgcm.conferenceacademy.com, to view the membership of the board and the committee and to access previously published papers."

Jan 1, 2015

By J. A. Caldwell, G. E. Blight

The metropolitan area of the Witwatersrand has grown up around the Witwatersrand gold mines. Most of the mines have now been abandoned, but deposits of waste material remain and have been surrounded, and in some instances covered, by urban and industrial sprawl. This paper describes the development of geotechnical measures for the abatement of air and water pollution from abandoned gold-residue dams in the Witwatersrand area. The measures include the stabilization of the surfaces of the dams to prevent wind and water erosion, the terracing of slopes to minimize erosion, and the construction of catchment walls and dams. The measures were developed in terms of the set of guidelines for environmental protection adopted by the Chamber of Mines of South Africa in 1979.

Jan 1, 1983

By E N. Isaev, L E. Levin

New data on the geology of the Late Jurassic to Holocene sediments cover of the World and associated mineral resources (oil, gas, ferromanganese nodules, ores of massive sulphides and other metals) have been compilled in the Atlas at scale 1:25,000,000 and 1:10,000,000. The work was performed by scientists from four Institutes of Russia (VNIIzarubezhgeologia, VNIIoceangeologia, Vernadsky Institute of Geochemistry and Analytical Chemistry of theRussian Academy of Sciences and Geological Institute of the Russian Academy of Sciences). The Atlas shows variation of thickness and formational composition of the large complexes (Upper Jurassic-Early Cretaceous, Upper Cretaceous Eocene, Oligocene-Neogene, Pliocene-Pleistocene), distribution of oil/gas and ore deposits in each complex, data of deepsea drilling (leg 1-130),  thermo-pressure condition in the sedimentary basins within Circum-Pacific Rim.

Jan 1, 1995

By O. W. Kamper

To most of you present here the word "refractories" is not new and you are familiar with the materials and use. To many people though the question is asked, "What are refractoriness and what are they used for?" Refractories are non-metallic products which are so resistant too melting at very high temperatures that they can be used for building or lining furnaces of all kinds. A large variation occurs in the size, form, and composition depending on the service for which they are intended. They are made from a wide variety of raw materials, of which fire clay and quartzite are used in largest quantities. Other refractory raw materials include magnesite, chrome, diaspore, bauxite, kyanite, sillimanite, olivine, zircon, and many others. Most of these are assembled from-widely-'separated points in the United States while others come from the far corners of the earth. Chrome is imported from the Philippines and South Africa, and, to a lesser extent, Turkey and Greece Kyanite and sillimanite come: from India and bauxite from the Guianas. And there's "magnesite from brines," produced in chemical plant's by treatment of sea water or inland deep-well brines with hydrated lime. The proportion of magnesia available in sea water is so small, less than one pound from 500 pounds of water,, that millions of gallons must be pumped and processed each day in a sea water magnesite plant. The realm of refractory raw materials, therefore, is very extensive and continues to grow because of the endeavor to find-better raw materials from which to produce better products for refractory service.

Jan 1, 1960

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Diesel-powered locomotives designed specifically for underground operation were used in the construction of some of the tunnels that comprise the Delaware Aqueduct in New York State. Before this there had been limited use of Diesel-powered equipment such as trucks, bulldozers, and shovels in tunnel construction in various parts of the country, but this equipment was used without modification for underground use and, in some instances, appar¬ently without due consideration of the hazards that might be created by the introduction of fuel-burning equipment into confined underground spaces.As certain definite advantages were apparent if Diesel haulage could be used in tunnel construction in some sections of the Aqueduct, the contractors who were to construct the tunnels in these sections were desirous of using, this type of haulage equipment if it could be used with safety. This matter was given careful consideration by the various agencies concerned with the establishment of safe practices on the Aqueduct project before tunnel driving was started. Of chief concern were the quantities of toxic or objectionable materials that would be discharged into the tunnel air by the exhaust of the locomotives and the volume of ventilating air that would be required to dilute these exhaust gas products to concentrations permissible in the atmosphere of working places."

Jan 1, 1947

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay and shale mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, it is essential to the technical discussion and study of methods employed to consider operating costs. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scone of the cost tabulations shale ensue. The open-pit recovery of clay and shale is a comparatively simple operation in comparison with underground mining; nevertheless, it represents an appreciable factor in the cost of manufacture.

Jan 1, 1936

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020