Search Documents

By W. I. Garms

This paper, describing the milling practices at the Hayden concentrator of the Nevada Consolidated Copper Co. is the first of a Series being prepared by the Bureau of Mines on milling methods and costs in various districts of the United States. The Hayden concentrator is located at Hayden, Gila County, Ariz., 20 miles from the mine at Ray, Pinal County, Ariz., and approximately 1-1/2 miles north of the junction of the Gila and San Pedro Rivers. During the fourth quarter of 1928 the concentrator treated daily by flotation an average of 10,336 tons of ore containing 1.25 per cent of copper. The average recovery during this period amounted to 87.84 per cent of the total copper. The concentrates contained 19.88 per cent of copper.

Jan 1, 1930

By G. A. Murphy

This tipple differs from the ordinary tipple only in that it embodies numerous refinements for grading and otherwise preparing the coal. Coal from the mines is delivered to the tipple over a surface tram. There are two tracks for loads, which will hold about forty cars, and one track for empties which will hold about the same number. The loads are fed to the dump by gravity from both tracks and are controlled by two squeeze blocks. These blocks are of the type originally designed by Mr. W. J. Elwood, but unlike the original blocks which were of wood and operated by hand levers, are built of steel and operated by com¬pressed air at 100 pounds pressure. They are capable of holding securely twenty-four three-ton cars on a grade of 2.5%. The dump is of the complete revolving type and has a capacity of five cars per minute. After being dumped the empty cars go to the usual kick-back and onto the empty track by gravity. The hopper under the dump has a capacity of approximately fifteen tons, and the coal from this hopper is fed to the shakers by a reciprocating feeder. The screens are of the usual shaker type. They are eight feet wide, seventy-two feet long in two sections, balanced, pitch 12° 30", travel six inches and the eccentric shaft makes 100 revolutions per minute. The upper section of the screen is shorter but heavier than the lower section, and contains the slack and nut screens, consisting of plates with 1 5/8" and 3" round perforations respectively. The lower section contains plates with 4 ½ ", 6" and 8" round perforations respectively, from top to bottom in the order named. The shaker is so arranged that nearly all changes for making the different sizes of coal are made by merely shifting levers. The most complicated change has been made in two and a half minutes; most of the other changes can be made in less than one minute and some of then without stopping the shaker. One of the refinements is what we call the degradation screens. Just before the coal leaves the shaker it goes over a screen with 1 3/8" round perforations, which takes out the fine coal made while the coal is going over the other perforations. This fine coal goes into hoppers and onto the degradation conveyor and to the slack chute. The different sizes of coal, excepting the slack, are delivered by the shaker onto three picking tables. These tables are horizontal for twenty-four feet and then hinged to form the loading booms, so that each picking table forms a unit of continuous conveyor. Centrally located under the picking tables and under the floor, is the refuse conveyor which runs at right angles to the tables. The impurities picked from the coal are dropped into openings in the floor and onto this conveyor, from which they are discharged into a bin of 100 tons capacity. From this bin the refuse is loaded into railroad cars through a gate. The slack may be loaded directly into railroad cars through a chute from the hopper under the shaker, or it may be conveyed to the rescreener. Gates are provided by which all or any part of the slack may be loaded either directly into railroad cars or conveyed to the rescreener. The rescreener is a shaker four feet wide with sixteen feet of plate perforated with 3/4" round holes. The framework is wood, the pitch is 5° and it is driven by eccentrics having a 5 3/4" throw running 143 R.P.M. It is hung on 1"x10" ash boards, rigidly fixed at the support and on the shaker, so that the spring of the boards allows for its movement. The eccentric rods are also of ash, rigidly fixed and spring to allow the movement of the eccentrics. The dust going through this shaker drops into a bin of 80 tons capacity and is loaded into railroad cars

Jan 1, 1925

By Francisco Gallo

La transformación de una empresa no solo depende de la capacidad de compromiso y cambio de la alta gerencia, sino se relaciona con la adopción de una tecnología iexitosa que transmita a la organización, un conjunto de paradigmas, procesos y política que el tiempo amerita. En este sentido, el presente trabajo describe el desarrollo de la tecnología informativa en la empresa minera Atacocha a través de las áreas de actividad productiva y administrativa. Para ello, es necesario que la empresa realice ajustes en su organización, procedimientos y políticas, de forma que se pueda aprovechar la inversión de una tecnología. Asimismo, los impulsores del cambio deben hacer el esfuerzo de identificar los medios por los que las premisas sobre las que se basa el cambio y la instrumentación de los mismos, permitan ser absorbidas gradualmente por la organización.

Sep 13, 2001

By T. A. Rickard

An educated man is distinguished neither by his clothes nor by his knowledge; he is replarkable not for the things he says, but for the way he says them. You cannot even stand with him under an archway in the rain without finding him out. He may talk only of the weather. His words and his phrases alike may be simple. -at distinguishes him is the arrange- ment of his words; however desultory his talk, it will be method- ical; he has habituated himself to foreseeing the part to be played by each word he uses and the place to be taken by each sentence he utters. On the other hand, the uneducated man, though shrewd and well-informed, will relate facts and events as they recur to him, generally in disorder; in his effort to recollect and in his attempt to rectify forgetfulness he will pause irregularly, filling the intervals with meaningless phrases, such as "and then ", "and: so ", or 'said he to me", "said I to him"; and even the contipuous parts of his story will be told confusedly-because he has not learned the proper use of words.* My own experience as an editor of technical manuscripts has taught me that the misuse of 'that' and 'which' is a fruitful cause of obscurity and confusion. The relative pronouns have distinct functions, and no writer can express himself clearly until he has learned to discriminate between these I functions. For example:

Jan 1, 1931

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

Jan 1, 1967

By Eric Forssberg, Vigen Zeng

During mechanical grinding high intensity vibration is emitted that contains information on the mill's operating state. Tests, using a laboratory ball mill, studied the influence of operating parameters on the vibration signature. The parameters studied were: mill speed; powder filling; pulp density; grinding period; and pulp temperature. Vibration signals were detected by an accelerometer, amplified by a vibrometer and recorded onto digital audio tape. A digital oscilloscope converted the signals into IBM-compatible data format. Digital signal processing and multivariate data analysis were carried out with specially developed software. The power spectral density was estimated from the time-domain vibration signal. Four new latent variables were used to describe changes in the vibration spectra. A relationship was established between operating parameters and latent variables which could form the basis of a quick and automatic method of monitoring operating parameters in ball mill grinding.

Jan 4, 1993

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By W. J. Asselstine

Introduction This paper is prepared from data gathered for a similar paper to be submitted to the United States Bureau of Mines, for publication as one of their information circulars. It covers the history and development of the present milling practice at Premier. The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by D. L. Pitt, Manager of the Premier Gold Mining Company, Limited; also their indebtedness to various members of the Engineering Staff and of the Accounting Department who have assisted materially in gathering the data used. Location The Premier mine and mill are situated in northern British Columbia, approximately fifteen miles north of the head of Portland canal, in the Salmon River section, about half a mile east of the Alaska-British Columbia boundary line where it crosses die Salmon river. The mill is located on a rather steep hillside on the horizon of the main haulage level of the mine, and is within a hundred feet of the mouth of the tunnel. Both the mine and mill are connected with tidewater at Stewart, B.C., by an aerial tramway (1) eleven and one-half miles in length, which delivers both ore and concentrate to the bunkers at the dock for shipment to the smelters. All mine and mill supplies are transported from Stewart dock to Premier over this tramway, except heavy machinery. Heavy pieces have to be hauled either by truck in summer or sleighs in winter over a good road which runs from Stewart dock to Premier.

Jan 1, 1933

In the interest of safety in mining, the Bureau of Mines recommends: 1. That cages or skips used for hoisting or lowering men in vertical and steeply inclined shafts shall be provided with safety catches designed to prevent falling of the cage or skip if the hoisting rope or other connections break; and 2. That cars used. for hoisting or lowering men with ropes in slopes shall be provided with arresting devices, other than ordinary brakes, that come into action if the hoisting rope or other connections break. In presenting this decision, it is recognized that the principal requirements for safety in hoisting operations are the use of hoisting ropes of ample size and strength to provide a factor of safety recognized as adequate by the best en engineering practice; their proper care, protection against undue wear and corrosion, and frequent inspection; and immediate removal of ropes from service when inspection or tests cast doubt upon their further safe serviceability.

Jan 1, 1938

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

Adhesion of Escherichia coli onto Oxide Minerals - Extended DLVO Theory and Flotation Behaviour

Sep 13, 2010

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R and TGA testing setups in our ventilation laboratory, samples from US coal mines have been collected and tested. 70 The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal which is a good indicator for potential of self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential of coal self-ignition. The trend of activation energies determined using TGA techniques and adiabatic tests are reasonably consistent with each other. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal are easier to be activated with a small amount of activation energy at a relatively low temperature, the coal will has a higher potential of self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with low potential of self-ignition has low self-heating rate, high activation energy and high minimum self-heating temperature.

Jan 1, 2012

Jan 1, 1967

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By Dale Verran, Jared Orynik, Chad Sorba, David Bronkhorst

Denison Mines Corp. (“Denison”) has a 90% interest in the Wheeler River Uranium Project (“Wheeler River”) located along the eastern edge of the Athabasca Basin in northern Saskatchewan between the Key Lake mill and the McArthur River uranium mine. The project is host to the high-grade Phoenix and Gryphon uranium deposits, discovered by Denison in 2008 and 2014 respectively, which include combined Indicated Mineral Resources of 132.1 million pounds U3O8 (1,809,000 tonnes at an average grade of 3.3% U3O8). The Pre-Feasibility Study (“PFS”), completed in accordance with NI 43-101 in September 2018, is highlighted by the selection of the In-Situ Recovery (“ISR”) mining method for the development of the Phoenix deposit, with an estimated average operating cost of $4.33 (US$3.33) per pound U3O8. Phoenix is the highest-grade undeveloped uranium deposit known globally, including Indicated Mineral Resources of 166,000 tonnes at 19.1% U3O8 for 70.2 million pounds U3O8. The paper aims to provide a summary of Wheeler River and an overview of the proposed development of the Phoenix and Gryphon deposits according to the PFS completed for the Project. Further details regarding the PFS, including additional scientific and technical information are described in greater detail in the NI 43-101 Technical Report titled "Pre-Feasibility Study for the Wheeler River Uranium Project, Saskatchewan, Canada" dated October 30, 2018 with an effective date of September 24, 2018. A copy of this report is available on Denison's website and under its profile on SEDAR at www.sedar.com and on EDGAR at www.sec.gov/edgar.shtml.

Jan 1, 2020

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

By Donald E. Stump

Subsidence from underground coal mining alters surface water discharge and availability. The magnitude and areal extent of these impacts are dependent on many factors, including the amount of subsidence, topography, geology, climate, surface water - ground water interactions, and fractures in the overburden. These alterations may have positive and/or negative impacts. One of the most significant surface water impacts occurred in July 1957 near West Pittston, Pennsylvania. Subsidence in the Knox Mine under the Coxton Yards of the Lehigh Valley Railroad allowed pan of the discharge in the Susquehanna River to flow into the mine and create a crater 200 feet in diameter and 300 feet deep. Fourteen railroad gondola cars fell into the hole which was eventually filled with rock, sand, and gravel. Other surface water impacts from subsidence may include the loss of water to the ground water system, the gaining of water from the ground water system, the creation of flooded subsidence troughs, the increasing of impoundment storage capacity, the relocation of water sources (springs), and the alteration of surface drainage patterns.

Jan 1, 1986

By S L. Nicol, B J. Hogg, O J. Mendoza, S Nikolic, A Burrows

The top submerged lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. The key advantage the ISASMELT™ TSL technology provided was the ability to process feed materials in a highly turbulent bath, reaching close to equilibrium conditions, uniquely allowing for operation below the liquidus of the molten slag phase. The details on what happened below the liquidus line in the phase diagram became critical for the successful operation of the technology. During the development of the ISASMELT™ technology this led to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore Technology, and the Pyrometallurgy Research Centre (PYROSEARCH) at The University of Queensland. The fusion of the phase equilibria research into the technology development allowed for understanding of the behaviour of molten splash, reliable tapping of the furnace, and the ability to operate the furnace with a refractory lining and achieve a year campaign life in excess of four years. The outcome has allowed for the highly successful adaption of the ISASMELT™ technology to recycling of complex feed streams necessary to drive circularity in our modern global economy.

Aug 21, 2024