Search Documents

By Yuanbo Zhang

Zinc leach residues produced by hydrometallurgical zinc plants contain many valuable elements (zinc, iron, lead, gallium, indium silver, etc), while they have not been utilized effectively hitherto. In this paper, a new process of flotation-reduction roasting-magnetic separation to recover these valuable elements from zinc leach residues is developed on a basis of mineralogy investigations of them. The results show that silver concentrate with grade of 4321.6 g/t and recovery of 80.69% have been obtained, using 1750 g/t Na2S as conditioner, 750 g/t ammonium dibutyl dithiophosphate and SN-9 (assistant collector) as combined collector and 100 g/t terpenic oil as frother, if zinc leach residues with 523 g/t silver are floated at pH = 5.0. When the flotation tailings are subjected to reduction roasting at 1100? for 2 h, the volatilizations of zinc, lead and indium are over 96%. After roasted products are treated by wet-grinding and magnetic separation, the grade of gallium and gallium in the concentrates achieved respectively reaches 1805 g/t and 1536g/t, and the recovery of them is high to 94.67% and 93.20%, respectively.

Jan 1, 2006

These inspection standards have been prepared for use in the Federal inspection of bituminous and lignite mines. They are a revision of "Tentative Coal-Mine Inspection Standards," published as Bureau of Mines Information Circular 7204 in February 1942 and employed a guide for Federal inspections. Numerous changes have been made in the original standards owing in part to recognition of shortages of some types of safety equipment due to the war, in part because of need of additional standards to cover certain mine conditions' arid' practices, and in part to conditions not foreseen when the original standards were prepared. About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however; failure to carry out the suggestions made in such of the other standards as are applicable may also' lead' to the loss of lives.

Jan 1, 1943

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A. C. Johnson

The Bureau of Mines explored the Three Kids deposit in 1941 as part of a strategic minerals program. Earlier mining and exploration had established the presence of a substantial tonnage of medium-grade wad ore, and drilling and sampling by the Bureau of Mines, in collaboration with the Federal Geological Survey, indicated an additional tonnage such that development and exploitation became more clearly feasible. Private interests, with Government support, undertook to produce metallurgical-grade manganese. The present paper describes the Bureau of Mines exploration and subsequent development. Manganese in the Three Kids area is found in one of the lower members of the Muddy Creek formation in a bed of fine sandstone and silt, which outcrops around the north edge of the River Mountains and generally dips 20° to 40° away from the hills. There is considerable variation in the thickness and grade of the ore. The ore is light weight, having a density of 1.2 to 2.

Jan 1, 1956

By Tiago Silva Costa

O processo que envolve soluções aquosas para remoção do metal de valor de uma grande massa de ganga, com um beneficiamento mínimo, é denominado Lixiviação. A especificidade do agente lixiviante empregado define a capacidade de tratar soluções com baixos teores do metal de interesse e o sucesso do processo. A lama da aciaria, recolhida no sistema de limpeza dos gases oriundos do convertedor LD, e a lama da eletrogalvanização, gerada após a neutralização da solução de zinco contaminada com ferro, são resíduos sólidos gerados nas usinas siderúrgicas com potencial de serem reutilizados ou reciclados. A fim de se remover o óxido de zinco presente nas lamas, amostras foram coletadas e preparadas para sofrerem o processo de lixiviação em escala laboratorial usando soluções de hidróxido de sódio (NaOH) e ácido sulfúrico (H2SO4). Os resultados obtidos nas análises mostraram que é possível remover óxido de zinco através da lixiviação das lamas.

Aug 16, 2017

By R J. deMelo, A, V Suckal, R A. Vilela

Massive hematite ore (MHO) is a special high-grade iron ore used as lump ore in the process of obtaining direct reduced iron (DRI). The influence of porosity on the reducibility was investigated using optical and scanning electron microscopes. Hematite is the main component of the samples and occurs as granular crystals (10 ¦m), microplates (1 ¦m) and euhedral martite (10 to 30 ¦m). Quartz, maghemite, kenomagnetite and goethite are minor components. Primary micropores (+ to 1 ¦m) are associated with microplaty crystals that fill cavities between granular hematite. Secondary micropores (+ to 5 ¦m) related to euhedral martite crystals are the most important. The total porosity of weathered samples, measured using nitrogen adsorption and mercury injection, attains values up to 18 per cent, whereas unweathered samples have a porosity less than 2.5 per cent. Varajpo et al, 2002 showed that reducibility is strongly enhanced by porosity and this work shows that reducibility can be indirectly evaluated by bulk density.

Jan 1, 2002

A New Cell for Electrochemically Aided Flotation

Sep 13, 2010

By O. C. Blade

"An important function of the Bureau of Mines is promoting the conservation and more efficient utilization of a natural resource. Petroleum is such a resource, and its utilization depends to a considerable degree upon its characteristics. For this reason the Bureau of Mines, over a period of years, has analyzed many samples of crude petroleum by the Bureau of Mines Hempel method 3/ and published complications of crude-oil analyses. Among such publi¬cations are several reports presenting analyses of crude oils from fields in Oklahoma. The most recent of these relates to samples from southern Oklahoma. 4/ The present paper provides additional analyses of Oklahoma crude oils, largely from areas and formations not heretofore represented in published reports. The analyses of 248 samples from 153 fields are presented individually and collectively in the tables of this report.Crude oil has been produced in Oklahoma in commercial quantities since 1891, and peak production was reached in 1947. The State's cumulative production to January 1, 1944, is, according to the American institute of Mining and Metallurgical Engineers, 5,186,466,000 barrels. 5/ The annual production of crude petroleum in Oklahoma for each year from 1891 to 1943, inclusive, is given in table 1."

May 1, 1945

By E. W. J. Thornton

During the past six or seven years extensive research has been performed on ore samples procured at the Bruns1,vick Tin Mines which is located in the south-west corner of New Brunswi.ck. This property was originally staked by Mount Pleasant Mines and they did considerable metallurgical and geological work on a small copper, zinc and tin deposit. In 1969, the property was obtained by the Sullivan Mining Group and after much geological and diamond drilling work, an entirely separate ore body \Vas located two miles south of the previous workings. The major economic metals in this ore zone are tungsten, bismuth and molybdenite, but many other metals exist as well. As the ore contains a host of different mineral species, it can be seen that considerable time WRS required to develop a practical flow sheet.

Jan 1, 1977

By Warren H. Weisz

A cement, in the broad sense, is any substance which will cause various materials to adhere to each other. Clay was probably the first material to be used by man as a cement or binding agent. Water occurs in or is mixed with the clay to make it plastic, so that it can be formed in place. The sun and air remove the water from the clay and on drying strength is developed. The clays unless fired are not too resistant to water, therefore, their use is best when restricted to dry areas. Gypsum used as a cementitious material is not the subject of this paper, but its use dates back thousands of years. Gypsum mortars were used by the Egyptians in building such massive masonry structures as the pyramids. The Egyptian mortar consisted of a mixture of sand with burned gypsum (of an impure type of 81.5 per cent calcium sulphate and 9.5 per cent calcium carbonate) for the cementitious material. The burning of this type of cementitious material took place at relatively low temperature. These burning reactions will be covered later when the dehydration of gypsum is discussed. The setting of the partially dehydrated gypsum is considered to be crystallization from a supersaturated solution which deposits crystals of dihydrate (gypsum). In low water-content mixes, the interlocking of the needle-like crystals helps to produce higher strengths. Slaked lime made from limestone burned at higher temperatures (1648 F is generally considered as the calcining temperature, although under certain conditions incipient calcination will take place at 1250 F) is another early-period cementitious material. During slaking with water, a colloidal or amorphous hydrated lime is formed. When it is allowed to dry, it hardens and develops low strengths. On exposure to the carbon dioxide of air in the presence of some moisture, carbon dioxide is adsorbed and part of the calcium hydroxide is converted to calcium carbonate. Structures in which a lime mortar is used continue to grow in strength as this reaction proflesses. Hydrated lime has the disadvantage of not setting under water.

Jan 1, 1960

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By Sean Gallagher, Thomas G. Bobick, William S. Marras

Twelve healthy, experienced underground cool miners performed lifting capacity tests in stooped and kneeling postures using a modified psychophysical procedure. Subjects adjusted weight in a lifting box to the maximum they could handle without undue fatigue in an asymmetric lifting task. Lifting periods were 20 min in duration and the frequency was 10 lifts/min. Tests were performed under a 48-in. roof that restricted the subject&apos;s posture. Psychophysical. physiological, and biomechanical dependent measures included the maximum acceptable weight of lift (MAWL), heart rate (HR), rate of oxygen consumption (VO2), ventilation volume rate (VF), respiratory exchange ratio (R), and integrated electromyography (EMG) of eight trunk muscles. Results indicated that the MAWL was significantly lower when kneeling than when stooped (p < 0.05), Furthermore, metabolic demands were greater in terms of HR (p < 0.005) mid VO2 (p < 0.05) when kneeling. Left and tight erectores spinae muscles exhibited increased EMG activity- in the kneeling posture (p < 0.001). It was concluded that psychophysical lifting capacity is decreased, while the metabolic stress and internal load on the spine are increased, in the kneeling posture. Results of this Bureau of Mines study indicate that it may be advisable to reduce the weight of materials that are handled repetitively in the kneeling posture.

By C. J. Brown

Since its commercialization thirty years ago, the Recoflo® short bed ion exchange process has been extensively utilized for the recovery of a wide variety of acids and metal salts. In addition to a reduction in resin bed height from 200 cm to 300 cm to 15 cm to 60 cm, the process has a number of features such as utilization of fine mesh resins in a compressed bed which together make it ideal for a number of applications. The process has been extensively exploited, for example, in the metal finishing industry for recovery of valuable chemicals from electroplating, anodizing, etching and pickling wastes. More recently, it has also been applied in the primary metals industry for purification of copper electrolytes and metals recovery from leachates. The paper discusses several of these applications and some of the issues that were found to be key to their success.

Jan 1, 2004

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By Rafael Wilson Soares Ladeira

Realizar manutenções preditivas de forma cada vez mais assertiva é um dos benefícios da atual evolução dos sistemas produtivos industriais conhecida como Indústria 4.0. A Sotreq - revendedora Caterpillar - oferece um serviço de análise de fluidos a partir da coleta periódica para máquinas operantes em campo. Com os resultados das medições, especialistas atribuem às amostras um nível de criticidade, justificativas e recomendações. Neste trabalho propõe-se uma solução que aumentou a eficiência desse processo através da utilização de modelos de Machine Learning treinados com as análises já realizadas que automatizam a classificação e a geração do texto de diagnóstico para novas amostras. As predições do sistema foram consideradas bem sucedidas, com métricas de sensibilidade e especificidade acima de 88%.

Oct 30, 2017

By S Sandover, D Glenister

Alcoa World Alumina Australia is committed to sustainability principles as a basis of business success into the future. In March 2001, Alcoa Inc chairman Alain Belda announced a set of far-reaching environmental goals for the corporation, with the challenge that they should be achieved in ways that enhance economic and social performance, while substantially reducing environmental impact. Application of Cleaner Production methods is seen as the key to achieving these joint objectives. In Australia Alcoa has launched a co-ordinated effort to accelerate our application of Cleaner Production principles to delivering cost-effective in-process solutions to environmental issues. Our Western Australian Operations are a signatory to the WA Cleaner Production Statement, through which we provide a Cleaner Production Plan to the State Government on a voluntary basis. This paper describes in general terms AlcoaÆs goals, achievements and directions in applying Cleaner Production to enhance business performance in the economic, environmental and social dimensions. Quantification of the benefits and tracking of progress in quantitative terms is a key challenge for the future

Jan 1, 2002

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

By Benedicto Hadad Cintra

In an inflationary environment the need for reduced cost is a daily concern of all industries. The Du Pont do Brasil "Expanded Pattern" method has proven to be an extremely effective means of reducing costs in mining, quarrying and construction operations. Over the past years much emphasis was placed on rectangular drilling patterns where the burdens are less than the spacing. The Expanded Pattern method combining rectangular and staggered patterns, was implemented in 1971 in Brazil after extensive trials in close collaboration with numerous explosives users and Du Pont do Brasil Technical Services Engineers. The best multiple row spacing-to-burden ratio (S/B) was demonstrated to be in the 2 to 5 range and the effective spacing to burden ratio (Se/Be) was found to vary from 5 to 11. These ratios are for the interior of the blast pattern and do not hold true along the front row of holes. Geological rock properties, hole diameter and inclination, explosives energy and loading density, explosives characteristics, blast pattern geometry, bench height and delay patterns along with type and size of digging, hauling and crushing equipment must all be evaluated for each and every operation. The integration of these interrelated parameters, together with sound blasting practices are the basis for the Expanded Pattern method. Color slides and documented case histories will be presented.

Jan 1, 1985

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983