Search Documents

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

By M. C. Makepeace

"It is the objective of designed experiments to obtain more information for less material and process cost than can be obtained by traditional experimentation. In this paper, the fundamental concepts on which the statistical design of experiments is based are briefly re-viewed according to the following outline: The Experiment The Design The Analysis Two simple 2"" factorial experiments are presented as examples."

Jan 1, 1967

By Mark E. Schlesinger

Engineering design follows a six–step sequence. Demonstration of this sequence in materials engineering is less common. A case study is presented, using the 1989 paper by Gafner on the development of 990 gold-titanium alloy. This paper identifies a need, develops the problem, identifies alternatives, demonstrates the use of metallurgical principles to identify alternative responses, and shows how more favorable options are selected. The paper can also be used to illustrate engineering design as an iterative process. The paper is also useful as a starting point for more in-depth examination of specific elements of the design process, and lends itself to the creation of student exercises.

Jan 1, 2014

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By Fábio Luiz dos Santos

As ligas de alumínio, em particular, apresentam certas restrições quando submetidas ao processo de união por soldagem. Isto se deve, principalmente, por apresentarem elevada condutividade térmica, elevada contração na solidificação e elevada solubilidade de hidrogênio. Levando em conta estes aspectos, o processo de soldagem FSW apresenta grande potencial para esta aplicação, visto que, é autógena, realizada sem fusão do material e sem utilização de escórias ou gases de proteção. A partir deste conceito, o objetivo do presente trabalho é avaliar a união de chapas finas de alumínio da liga 3105 H26, com espessura de 0,7mm. Para realização dos testes, foram analisados fatores como: penetração da ferramenta nas chapas processadas, ângulo de ataque, tipo de ferramenta e modo de controle de penetração (posição ou força). Os resultados indicaram que o modo de controle por força se mostrou o mais indicado para chapas finas, e que o regime transiente no início de soldagem foi a parte mais crítica para controle da qualidade da junta soldada.

Aug 16, 2017

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

Ground conditions at the Kencana mine, Indonesia, are generally poor and an underhand cut and fill mining method is used for extraction. Due to these poor ground conditions, all vertical development has been conducted using blind, top-down, sink and line excavation methods. Due to time constraints, raiseboring was considered the only viable excavation method for the installation of a return ventilation system for the K2 (Kencana extension) project. In order to achieve successful raiseboring in the poor ground conditions a number of strategies were used including: a detailed geotechnical study for optimal position of the shaft/s, splitting shaft excavation vertically, raiseboring of multiple smaller diameter shafts, extensive pregrouting, installation of drainage holes, and rapid installation of support following excavation.

Nov 25, 2010

The New Zealand microcontinent is relatively well endowed with gold deposits; its past gold production per unit area of 3.2 kg/km2 ranks high on a world scale. Total recorded production (1857 - 1986) is about 854 000 kg and most of this gold was mined between 1861 and 1920. There has been a strong revival in gold exploration and mining since 1979, with exploration expenditure of around $15 million per annum and a declared gold production in 1986 of 1265 kg (886 kg in 1985). In addition to numerous alluvial gold recovery plants working small to medium sized deposits (mainly in Westland and Otago), there are five medium to large projects that have started production (Martha Hill), or have reached advanced stages of construction (Grey River dredge), permitting (Golden Cross and Macraes) or exploration (Globe-Progress). This summary paper is taken from reviews by Brathwaite et al (1986) and Brathwaite (1988).

Jan 1, 1988

By T. N. Williamson

Most U.S. coal production is bituminous coal. Some 90% of current production comes from a geographical area enclosed in a circle with a 300 mile radius and its center at about Huntington, West Virginia. There are important underground coal production areas in the western parts of the United States as well. Most U.S. coal production comes from fairly level seams, many of which pitch rather uniformly only a few feet per mile. Usually there will be several overlying seams of varying thicknesses, separated by several tens of feet. Fig. 1. 1. Seams have minor local undulations but these? are small enough not to be a major consideration in a horizontal drilling research program.

Jan 1, 1970

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

By A. F. Banks

"The last time I spoke to you the potash industry was at a low point. Markets were bad and the industry depressed. Many people had left and there was very little being done in terms of development. The current situation is very much changed. The oversupply conditions have given way to a very tight supply capability. All of the firms in the business are expanding in one way or another. These expansions will run from simple debottlenecking through to complete new projects.In New Brunswick, the Potash Corporation of America is proceeding with a new project and the Dennison - Potacan Project is in progress. In Saskatchewan, the Potash Corporation of Saskatchewan has an ambitious 2.5 billion dollar expansion program underway while those in the private sector are taking a somewhat less ambitious but equally significant approach to obtain further tonnage out of existing facilities.The significance of these expansions to mineral processors is that we can expect to see expanded employment opportunities and through necessity a surge in innovation and development in an industry that has been traditionally very conservative. This presentation will review potash processing with a view towards highlighting some of the more recent developments."

Jan 1, 1982

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By S Munn

Today, it can be said that the majority of mines utilise communications equipment in one form or another. Either for communications between staff making their day-to-day operations more efficient, or for emergency communications, as well as linking computer based mine management systems, and providing remote control over complex mobile and fixed machinery. With the advances in technology now available, we are moving into the next generation of mine communications equipment, using digital communications in the underground mine environment. It is a proven fact that an efficient underground mine communications system can help maximise production, by providing major gains in areas such as equipment and manpower utilisation, staff and vehicle tracking, reaction times to break downs and emergencies. In this paper we will describe some of the facilities that are currently available, as well as what will soon be available to mining and tunnelling companies around the world.

Jan 1, 1999

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By Colin Hardie, Simon Pelletier, Rakan Rhabani, Guy Comeau

"In order to improve the nickel concentrate thickener operation at Raglan Mine, two pulp deaeration cyclones were installed. These units obtained from Outotec Pty Ltd, also called the FrothBuster®, have been in continuous operation since mid-October 2006. The primary objective of the de-aeration cyclones is to lower the solids content in the thickener overflow by de-aerating the concentrate pulp before it enters the concentrate thickener. This dearated slurry should help decrease the nickel particle losses that report to the thickener overflow because of the flotation effect within the thickener.Optimizing the de-aeration cyclones has been a slow and ongoing process, however, initial testing is encouraging. The latest test results indicate a 50 % reduction (0.070 to 0.035 % solids) in nickel losses to the concentrate thickener overflow resulting in an additional $350,000 in annual revenues.This paper will present an overview of installing the de-aeration cyclones within a limited space, as well as the preliminary commissioning and testing challenges. This paper will also discuss the most recent concentrate thickener operating results since the de-aeration units were installed.INTRODUCTIONThe Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region has been in production since 1997. In early 2002, the concentrator implemented the Zero Process Water Discharge (ZPWD) project to recycle the process water to decrease fresh water consumption and reduce discharges to the environment. Due to this initiative, the chemistry of the process water changed significantly resulting in flotation concentrate streams, which were very frothy and difficult to manage. This phenomenon has resulted in operational challenges in many areas of the concentrator including slurry pumping, flow measurement and concentrate thickening.In October 2005, the Raglan Mine underwent a conversion from an AG mill to a SAG mill operation in order to increase throughput and to optimize key process areas. As part of this project, the first two North American pulp de-aeration (FrothBuster®) units from Outotec were installed to improve the operation of the concentrate thickener. The primary objective of the deaeration technology was to lower the solids content in the thickener overflow by de-aerating the concentrate thickener feed pulp. This in turn was to reduce the froth, which accumulates on the thickener surface, and more importantly reduce valuable nickel losses to the thickener overflow because of the flotation effect within the thickener."

Jan 1, 2008