Search Documents

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By Clinton C. Knox

To demonstrate the feasibility of unwatering ore reserves previously indicated in the virgin Melrose zinc-lead field in Kansas and Oklahoma, the Bureau of Mines .carried through a pumping project on the Park Walton farm in 1943. Due to success of the undertaking, attention was turned to exploration of other indicated ore deposits and promising areas within that part of the field benefited by .the drainage project, By the middle of 1946, four private mining companies were active in the field; and a considerable output of lead and zinc concentrate had been obtained from the new Park Walton mine and mill. The Park Walton Ore deposit was unwatered by installing deep-well pumps in three holes previously drilled by the lessee. Pumping was continued by the Bureau of Mines at a rate of 2,500 to 1,000 g.p.m. for about 6 months; during this time the local static artesian water-level, originally averaging 108 feet below the surface in the old drill holes was lowered to the 316-foot level, which justified beginning the initial shaft sinking and mine developments. In all, about 750,000,000 gallons of water was pumped by the Bureau of Mines at an operating cost averaging $0.024 per 1,000 gallons.

Jan 1, 1948

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By G. Griffiths

"P. WitteWitteck DevelopmentThe implications of using a tower mill for fine grainding in the ore processing of tailings are significant. What can those of us who are in a research and development situation do when we recommend this equipment to a client? When this prototype is placed on stream next to a conventional grinding mill as you suggest how do we estimate the power requirements and the grind which will be achieved?ReplyLet me explain the Macassa circuit. The tower mill here was running in parallel with one of the ball mills. The feed entering the tertiary system is scalped in a primary cyclone. The finial cut is made in a secondary cyclone. The actual feed to the tower mill is the underflow from the two cyclones and was split to the ball mill and tower mill. During the testing we were unable to isolate the tower mill to determine its contribution to the overall system. We then started to look at the amount of material produced across the mill. We entered the mill at between 17% and 20% finished material and exiting at between 36% and 40% finished material. We were able to project, with a high efficiency classification system, and arrived at 6 Kwh/ton or better."

Jan 1, 1984

By R Lewis

Drill hole magnetometric resistivity (DHMMR) is a relatively recent addition to the explorationistsÆ suite of techniques for finding further resources in the vicinity of a drill hole. The method relies on gathering of an applied current into zones which are less resistive than the country rocks and it was first applied to exploration programs looking for weakly conductive sulphides, such as, for example, carbonate-hosted zinc deposits. More recently, it has been applied to a wider range of deposit styles, including highly conductive nickel sulphides. It has been found that the technique is capable of not only detecting mineralisation not seen by conventional electromagnetic (EM) techniques, but it can detect at a greater distance. Also, whilst EM is superior at defining tabular-shaped conductors, DHMMR may be more effective at finding cigar shaped sulphides. This paper presents a number of examples illustrating these findings.

Jan 1, 2000

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By P. A. Plunkert, D. E. Morse, Pui-Kwan Tse, W. D. Menzie, Lucy McCartan, J. F. Papp

China’s burgeoning economy is responsible for a major share of recent world mineral consumption increases. In addition to factors traditionally recognized in market economies1 and factors unique to specific commodities, Chinese consumption now plays a major and increasingly important role in energy and mineral markets for many commodities, such as aluminum, copper, iron and steel, and oil. China has the world’s second largest economy after the United States. And its long-term importance to the minerals markets is even greater than indicated by its gross domestic product (GDP), which is currently less than two-thirds of that of the United States (Table 1). This is because China’s rising standard of living is accompanied by rapid industrialization and urbanization. Its consumption of mineral materials for infrastructure development for its very large population is significantly greater per capita than that of such developed economies as the United States, the European Union and Japan. In other words, China’s per capita production is rising at a rapid rate and will probably continue to do so for many years.

Jan 1, 2006

By J. W. Thompson

The term "minerals" when employed in a conveyance in the State of West Virginia is understood to include every inorganic substance which can be extracted from the earth for profit, whether it be solid, as rock, fire clay, the various metals and coal, or liquid, such as salt, and other mineral waters and petroleum oil and gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. TERM INCLUDES OIL AND OAS. The term "minerals" used to describe the interest in land granted or reserved bona fide includes petroleum oil and natural gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. INJUNCTION TO PREVENT RElllOVAL. The removal of ore from the premises of another without his consent will be enjoined. Barnes v. Esch (Oregon), 169 Pacific, 512, p. 518. TITLE TO MEXICAN BULLION-JURISDICTION OF FEDERAL COURTS TO DETERMINE. Where bullion within the jurisdiction of the Mexican Government was seized, condemned, and sold for war supplies by the Constitutionalist forces in the revolution acting under authority from Gen. Carranza, claiming to be the provisional President of the Republic of Mexico, a United States district court of Texas, into which State the bullion has been imported from Mexico, has jurisdiction to try and adjudge as to the validity of the title acquired by and through the seizure, appropriation, and sale by the Carranza forces as against an American citizen claiming ownership of such bullion prior to its seizure.

Jan 1, 1919

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By Samuel Filgueiras Rodrigues

An austenitic stainless steel ISO 5832-9 was deformed in a torsion test machine over the temperature range of 1,000°C – 1,200°C and strain rates of 0.05, 0.1, 1.0 and 5.0s-1. The Steel plastic behavior was studied by analyzing the flow curves shapes and using the constitutive equations under the conditions of thermomechanical treatment. The curves initially presented an increase in stress characterized by hardening work, followed by a drop in stress to an intermediate level that reached or not, for certain conditions, the steady state softening. The plastic flow curves of ISO 5832-9 steel displayed in three different ways: (i) Curves with continuous softening presenting plastic instability for low temperatures and high strain rates; (ii) curves type flat, here after the peak there is little variation of stress with strain presenting softening mechanism by higher contribution of dynamic recovery at low temperatures and low and intermediate strain rates; (iii) curves with softening after the critical deformation favored by high temperatures and low strain rates. These behaviors indicate the influence of the stacking fault energy (SFE) and precipitated particles on the softening kinetics of this steel.

Aug 8, 2018

By Márcia M. S. M. Pereira, Hervé Tavernier, Gérson T. Ferreira, Caio Nogueira Araujo Diniz, Fabio Luiz Lourenço, Wagner C. Moreira, Vinicius Cunha Aranda

Pós fluxantes desempenham um papel significativo na qualidade do aço durante o processo de lingotamento contínuo. Os pós fluxantes são escórias sintéticas usadas para lubrificar o molde durante o lingotamento contínuo do aço. Para que isso ocorra, o fluxante deve apresentar as seguintes funções: isolamento químico e térmico do aço, absorção de inclusões não metálicas do aço, lubrificação do molde e controle da transferência de calor entre o aço e o molde. O desempenho de cada função está relacionado às propriedades químicas e físicas do pó fluxante, que são dependentes de sua composição química e sua composição mineral, devido a sua relação com a taxa de fusão do material. A fim de garantir uma produção eficiente e de alta qualidade durante o lingotamento de um aço ultra baixo carbono, os pós fluxantes A e B foram investigados de acordo com diferentes propriedades físico-químicas. Diversos experimentos laboratoriais foram realizados para comparar o desempenho dos materiais A e B, visando à diminuição de captura da escória pelo aço no molde: avaliação do comportamento de fusão e fluidez, composição química e viscosidade. As temperaturas de processo foram avaliadas através de testes estatísticos, visando caracterizar o fluxo de calor e o trabalho de fricção durante lingotamento. Os testes industriais preliminares, realizados na Ternium Brasil, foram conduzidos com o objetivo de analisar o comportamento do pó fluxante durante a operação de lingotamento contínuo em relação a alguns aspectos operacionais e fornecer informações sobre sua influência na qualidade superficial do aço. Os resultados mostraram que, aumentando a viscosidade do fluxante, o consumo de pó tornou-se menor, levando a um maior trabalho de fricção e menor fluxo de calor no molde. No entanto, o comportamento da camada de escória mostrou que, apesar do aumento da força de atrito no molde, a espessura da escória foi adequada e não houve relatos de defeitos superficiais durante o uso do material fluxante de maior viscosidade.

Oct 1, 2019

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By William J. Kemnitzer

This study was made to show the growth of petroleum coking and to deter- mine trends and characteristics of marketing and utilization of coke on the West Coast, comparing these data with those of the United States as a whole. An earlier Bureau of Mines economic survey of petroleum coke was made in 1930 before the widespread use of coking processes. Data, derived from published and unpublished literature as well as from interviews with industry representatives, show a marked increase in the production of petroleum coke since the end of World War II. This increase resulted from the need of refiners to upgrade heavy residuums for which the demand was diminishing. Increasing coke production as well as significant market shifts away from California-produced coke have created excessive stocks of petroleum coke on the West Coast. The causes of these market shifts were based mainly on (1) economic factors and (2) certain undesirable qualities of some of the petroleum coke produced in California.

Jan 1, 1965

By A. Mazhary, T. Huff

Sensor-based ore sorting technology is a growing area of interest due to lower-grade ore deposits and higher costs of processing, among other reasons. Among the sensors currently utilized in the particle sorting industry, X-Ray Fluorescence (XRF), as the only sensor with elemental analysis capabilities, has always attracted more attention. Currently, the bench-scale amenability tests for this sensor are performed using hand-held XRF analysers. However, this testing method overestimates the performance of the XRF sorter, and therefore, the results from these tests can be misleading and are often mispresented. The work presented here was conducted on a copper mine and investigates how the sensor’s sensitivity to copper deteriorates under different testing methods. This work compares and correlates the results of an Olympus hand-held XRF analyser, static, and dynamic sorter responses with the actual grades of the rocks. The results confirmed that, the sorter response was extremely prone to blind spots. Furthermore, the results demonstrated that although the static sorter’s responses were comparable in terms of rock identification to those of the hand-held XRF analyzer and assays, the accuracy of the dynamic sorter response deteriorated both as a function of grade of the rocks as well as the potential for blind spots. INTRODUCTION Sensor-based sorting technology has been gaining increasing attention even by larger mining corporations as ore grades decrease, deposits get deeper and therefore cost of mining and processing increases. There are various types of sensors that are currently being used in the particle sorting industry such as X-Ray Transmission (XRT), Color, Electromagnetic (EM), Near-Infrared (NIR) and others. However, none of the sensors are capable of identifying and quantifying particles by the elemental content, except for X-Ray Fluorescence (XRF). XRF is a non-destructive, surficial analytical technique used to measure elemental composition of materials. X-ray fluorescence happens when a secondary x-ray (fluorescence) is released after a sample is bombarded by a primary x-ray source. From a sorting perspective, the most common and expected issues that are associated with XRF sorting are lower throughputs compared to other sensors due to particle presentation limitation as well as the need to wash the material before introducing to the sorter. However, one important issue that is mostly neglected is how the amenability tests are performed and how realistic the obtained results are. Current amenability test procedure utilises a handheld XRF analyser (such as an Olympus InnovX, as used in this work) on multiple, generally 4, sides of the rock and uses the average measured grade as a criterion for separation. While this is a widely accepted technique, it fails to consider some important factors such as exposure time and the distance between the sensor and the particle. These factors can significantly affect the sorting outcome.

Jan 1, 2019

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile cod in the used type of byproduct-coke oven, because they expend excessively and. exert side thrust, which ruins the oven wells. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking coals with as much low-volatile coal as possible and still have a mixture that mill not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile cool has been exceeded and ovens have been damaged. It is desirable, therefore, to have a reliable method of determining the expending tendencies of mixtures before they are charged into the ovens. Furthermore, coal changes somewhat in its properties as mining progresses, end therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used. ]

Jan 1, 1938

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By César Cánepa

Las especies minerales son los sujetos del quehacer metalúrgico -en tanto, el diseño, la optimización operativa y el monitoreo periódico de una planta de tratamiento requieren de un adecuado conocimiento de las características de los minerales involucrados. En ese sentido, el presente texto señala las particularidades de los minerales (tamaño de grano, composición porcentual y grado de liberación) y su determinación cuantitativa a través de técnicas que ostentan sofisticación, donde la primera característica no se determina mediante técnicas no microscópicas, mientras que las dos últimas son factibles de establecer mediante la microscopía óptica, utilizando la metodología desarrollada por uno de los autores. Dicha metodología es compatible con el entorno instrumental y tecnológico de la mediana y pequeña minería, aunque puede ser utilizada con igual beneficio por la gran minería. Asimismo se presenta dos ejemplos actuales de cómo la aplicación de estudios microscópicos al proceso metalúrgico que se utiliza en la mina Atacocha, un yacimiento polimetálico ubicado en los Andes centrales del Perú, se desarrolla exitosamente en la optimización del proceso.

Sep 12, 2005

By V. A. Danielson

The Bureau of Mines studied waste disposal methods a1 a coal mine in Kentucky and another in Alabama to develop cost estimates, to provide better knowledge of current practices, and to guide consideration of alternate disposal methods. Costs of the existing waste disposal systems at each mine were estimated using present-day costs of equipment and labor. Costs of waste disposal systems using alternate equipment were also estimated. Although total disposal costs were essentially the same for both operations, reclamation costs will differ because of different reclamation practices.

Jan 1, 1969

By W. P. Yant

Canister-type gas masks Pave become an essential part of the equipment of many industries, not only for use in .emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices, and this bureau bas become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932