Search Documents

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By J. J. Beresford

The primary function of a support slurry is to provide stability during excavation. Today foundation structures can be designed around the additional friction afforded by the absence of the filter cake attributable to the use of polymeric fluids as support slurries. These fluids use pseudoplastic fluid viscosity to advantage over the fragile thixotropic gel structures of bentonite. Many of today's polymeric fluids are environmentally acceptable for disposal directly to municipal sewers.

Jan 1, 1989

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Robert Boyd

The Diamond Markets ? Supply has continuously increased over the past 25 years ? However, global supply is expected to drop by 1 to 2% by 2015 ? Demand Driven Market ?Demand is expected to grow 3% annually through to 2015 ? Supply Squeeze Anticipated (2010 to 2015) ? Consumption is exceeding rate of discovery, mine development and reserve replacement ? These fundamentals are driving increased capacity and production at existing mines in South Africa, Botswana and Russia and new areas such as Canada ? Canada is now the third largest diamond producing country in the world ? These fundamentals are also driving record levels of exploration expenditures throughout the world with particular focus on Africa and Canada

May 1, 2006

By Sergio N. Monteiro

Wastes generated by our society and the question on how to dispose them is, nowadays, a relevant matter of concern. The objective of the present work was to characterize the technical properties of composites made of discarded jute sackcloth with its coarse wove fabric, serving as reinforcement phase, and polyethylene wastes collected from city dumps, as continuous matrix. Different amounts, up to 30 wt.% of jute plain weave, fabric were press molded at 160°Ctogether with sieved polyethylene particles. The resulting composites displayed mechanical properties that could compete with those of low-density wooden board. Both by presenting a solution to, otherwise, disposed wastes and by helping to prevent deforestation, the investigated composite may be regarded as an environmentally correct material.

Jan 1, 2006

By John Gross

From the time when man first pounded one rock upon another or used heat and sudden chilling with water to disintegrate rock, the art of crushing advanced but slowly to the mule-driven arrastre and the Chilean mill stage until the advent of power-driven appliances made material progress possible. The combined efforts of manufacturers and operators have made modern machines highly efficient mechanically. Although marked progress has been made along mechanical lines, the theory and conception of underlying principles have not advanced so rapidly. This lack of advance in theory may be attributed to the unfortunate situation resulting from the controversy as to whether the Rittinger or the Kick law is applicable to crushing. Many pages of the technical literature are burdened with theoretical discussions in favor of one or the other of these laws, which have tended to cloud rather than to clear the atmosphere.

Jan 1, 1938

Geophysical Abstracts 1 - 83 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey. Abstracts 112 and 113 were issued in mimeographed form by tine Bureau of Mines as Information Circulars 7256 and 7257. 1. GRAVITATIONAL METHODS 7004. Campbell, R. B. Florida's Geological Structure and Gravity. Proc. Florida Acad. Sciences for 1540, Gainesville, Fla., vol. 5, 1541, pp. 73-84.

Jan 1, 1943

Energy Dissipation in Long-Distance Slurry Pipelines

Sep 13, 2010

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976

By George A. Morgan

Output of mineral products was estimated to be unchanged in 1983 from that of 1982 with the exception of petroleum. The country began production of crude oil from the Seme Oilfield, and all output was exported. Wd and charcoal constituted 72% of Benin&apos;s total energy consumption, and imported petroleum products and electric power accounted for the remainder. Cement was produced from imported clinker. The gross domestic product (GDP) was $1,061 million in 1982, the latest year for which information was available.2 COMMODITY REVIEW Gold.-Exploration was underway at Perma by the U.S.S.R. as part of the United Nations development program. Gold had been produced previously at Perma, where a grade of 0.289 troy ounce of gold per ton was reported, An exploitation program for the deposit was to employ about 100 people, and output was targeted to reach 1,600 troy ounces per year. Recoverable reserves were put at 96,000 troy ounces.

Jan 1, 1985

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By Teele Tuuna, Voglers Eesti OÜ

Blasting operations are a strong and important part in any kind of building and mining industry, a shot-firer profession is one of the oldest professions in the civilized world. It still serves an important and ongoing purpose in the modern economy all over the world. Europe, nowadays, values strongly the mobility of workers, the movement of know-how and labor force between different countries inside Europe. There are no borders for most of the everyday professions.

Jan 1, 2018

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

A new series of reports called ?Mineral Perspectives" (MP&apos;s) has been initiated by the Bureau of Mines with the publication of MP-1 titled, "Far East and South Asia" by K.P. Wang and the staff of the Bureau of Mines. This new series parallels the creation of the recently announced "Minerals Commodity Profiles" (MCP?s). Both series are designed to provide current information on important sectors of the mineral economy to assist professionals in government, industry, and education in monitoring supply-demand relationships that have significant impact on our domestic economy as well as on the international scene. The orientation of the "Mineral Perspective" series is a geographic one which examines the mineral situation of a region or a country. The "Mineral Commodity Profile? series examines individual mineral commodities. They are in this sense complementary.

Jan 1, 1977

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster&apos;s New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

The authors summarise the development and recent advances in the reconstruction and visualisation of three-dimensional objects from point data and describe applications to the reconstruction of orebody shapes from drill-hole and other data. In particular, Dijkstra&apos;s algorithm is proposed and implemented as a means of optimal reconstruction of complex orebody and topographical shapes from irregularly located sample data. The surfaces of the shapes are constructed from triangular tiles and the algorithms proposed by the authors are guaranteed to find the optimal set of tiles that "best" construct the surfaces on the basis of specified objective criteria. The algorithms are illustrated by applications to a complex silver/gold/zinc/lead deposit.

Jan 1, 2002