Search Documents

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By Stephen Gerard Sawyer

This report presents a Fortran IV computer program for the structural analysis of space-frame protective canopies used in underground mines to protect equipment operators from falls of roof, face, or rib. This program entitled CANOPY permits rapid calculation of the elastic strength of a canopy for a variety of static loading conditions. Stresses in, and displacements of each structural member are computed and printed out. Additionally, identification of all members that have commenced yielding, weight of the canopy, total loads on the canopy, and maximum loads that the canopy can sustain elastically are output. Program description, input instructions, program listing, and two example problems are included.

Jan 1, 1972

By Michael J. Potter

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. In June, Azrock Industries was purchased by the R L. White Co. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); by Ziegler Chemical and Mineral Corp.; and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds.

Jan 1, 1985

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By Felipe Amélio de Lucena

Ligas amorfas e nanocristalinas à base de ferro apresentam propriedades excepcionais, como alta dureza e resistência ao desgaste com taxa de resfriamento entre 103 e 105 K/s. Assim, este trabalho objetiva a solidificação rápida (SR) da liga à base de ferro fundido (FoFo) com adições de Boro e Nióbio, resultando na composição química (Fe65Cr17Mo2C14Si2)88B8Nb4 (%at.). A liga foi processada através de melt-spinning, no forno Discovery® Plasma e Conformação por Spray (CS) e caracterizada por: DSC, DRX, MEV e microdureza Vickers. Foram obtidos: fitas amorfas (40 µm) através de melt-spinning, chapas (1,0 e 2,0 mm) por (SR) e CS da liga (Fe65Cr17Mo2C14Si2)88B8Nb4, com depósito (1,0 e 2,0 mm) e pós overspray (20 até 180 µm). A caracterização mostrou fitas amorfas, pós overspray nanocristalinos e chapas (SR) e depósito (CS) cristalinos com as fases: Fe-a, Fe-?, Cr7C3, FeNbB e Fe2B, com respectivas microdureza Vickers de 1044 ± 102 (HV1) para o depósito CS e 1480 HV para a chapa de 2,0 mm, mostrando alta dureza.

Aug 16, 2017

By James P. Ulery

In This Chapter [Geologic features associated with anomalous methane emissions Gas outbursts and blowers Methane drainage strategies for mitigating anomalous methane emissions and General considerations for a methane drainage program] This chapter summarizes how certain geologic features may be associated with unexpected increases in gas emissions during coal mining. These unexpected emissions have the potential to create explosive conditions in the underground workplace. Also discussed are the generally used practices to alleviate potential hazards caused by gas emissions associated with these geologic features. INTRODUCTION Unforeseen mine gas emissions in quantities sufficient to create hazardous conditions have been attributed to sources outside the mined coalbed since the first documentation of methane explosions in coal mines [Payman and Statham 1930]. Geologic features such as faults have long been recognized as conduits for gas flow from strata adjacent to mined coalbeds [Moss 1927; Payman and Statham 1930]. Other features such as sandstone paleochannels, clay veins, and localized folding have also been recognized for their impact on gas emissions into mine work-ings [Darton 1915; Price and Headlee 1943; McCulloch et al. 1975; Ulery and Molinda 1984]. The fact that strata adjacent to mined coalbeds can emit large quantities of methane gas into mine workings is not surprising from a theoretical perspective. Many researchers have recognized that during the burial and diagenesis of the organic matter forming today’s minable coalbeds, similar dispersed organic matter in adjacent strata has produced methane in quantities far exceeding the storage capacity of the coal and surrounding rock [Juntgen and Klein 1975]. It is not surprising then that large quantities of methane can remain trapped in these strata. A potential hazard occurs when mining of a nearby coalbed causes pressure differentials and mining-induced fractures conducive to gas flow into the mine workings from these strata. This gas flow may be facilitated or temporarily impeded by the presence of geologic structures or anomalies.

Jan 6, 2006

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By Peter P. Kopas

Study, analysis, fabrication and testing for canopies on Roof Bolters and Shuttle Cars in coal seams under 48?.

Jan 1, 1980

By D. Wolfe, K. Reid, T. Nunn

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. In order to minimize front-end rejects, and to allow for high throughput, the ore top size at Aurora has been set at a nominal 125 mm. These relatively large lumps have a significant effect on both pump performance and pipeline pressure gradient. Current design methods underestimate the solids de-rating effect of lumpy slurries in pumps, and do not accurately describe the distribution or magnitude of the lump effect on pipeline pressure gradient. Data from the Aurora hydrotransport systems has been compiled, to quantify the effect of lumps on the pump head ratio and pipeline pressure gradient, and how this effect changes as lump ablation occurs along the length of the pipeline. A model has been built, using a logarithmic curve, which predicts the effect of 125 mm lumps on pipeline pressure gradient as a function of velocity and the distance from the start of a hydrotransport pipeline. This model is applicable only to Aurora hydrotransport operation, but similar models could be developed for other operations using the same methods. Using accurate pipeline pressure gradients and pump head ratios when designing future hydrotransport pipeline systems will help improve their reliability and operability."

Jan 1, 2014

By Xinhua Wang, Qiangqiang Wang, Yubin Li, Shusen Li, Lifeng Zhang

"Numerical simulation on the fluid flow in a Flow-Control Mold (FC-Mold) were performed. The motion of inclusions were calculated. With FC-Mold, the flow pattern and surface velocity become more symmetrical, and at higher casting speed the velocity of liquid steel in the top region of the mold was largely reduced with the highest velocity of the meniscus reducing from 0.65 mis to 0.4 mis, and the meniscus shape became flatter. With FC-Mold, more inclusions approached to the surface of the slab and the amount of inclusion in the center of mold became fewer. Larger inclusions were easier to remove, however, the EM filed of the FC-Mold could hardly improve the removal of inclusions from the molten steel.IntroductionElectromagnetic brake technology is an effective method to control the flow pattern within continuous casting mold, together with other casting parameters, nozzle design and mold geometry [1-5]. Due to the interaction between the applied magnetic flux and the conductive molten steel inside the mold cavity, a force is generated in the direction opposite to the jet flow, which can decelerate the high speed steel jet from the SEN ports. The potential benefits include fewer surface and internal defects, fewer inclusion especially at higher casting speed. However if used imperfectly, electromagnetic forces can have opposite effect [6]. Numerical models are the best tool to optimize electromagnetic flow control. In the current study, numerical simulation was performed to investigate the flow field in a continuous casting FC-Mold, and the effect of different operation parameters on the flow, surface level and velocity in FC-Mold were discussed."

Jan 1, 2013

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By Efrén Peña Pino

El presente texto señala la aplicación del sistema SAP en la minería subterránea de Minsur. Este sistema operativo maneja las propiedades y procesos de la Sociedad Minsur, el cual cuenta con tres Centros, dos de los cuales son operativos (San Rafael y Pisco) al margen de la central de administración (Lima) y permite la planificación de todos los recursos de la empresa de manera integral, evitando imprevistos y una mejora de decisiones.

Jul 31, 2003

By Richard E. Danell

"Blasting is a principal step in the surface mining process for breaking and, in the case of overburdencasting, moving rocks and minerals. As many surface mines are coming to the end of theiroperational life, blasting can once again play an important role through the earthmoving operationsrequired to rehabilitate the minesite. Since blasting is such an energetic and destructive process, itis difficult initially to envisage its use in rehabilitation. However, blasting has found applications inmany civil engineering projects aimed at rehabilitation, including well digging, channelling and soilcompaction. For surface mine rehabilitation, the main purpose of earthmoving operations is toproduce a stable landfonn that will sustain revegetation. In particular, blasting can be applied toreducing the slope of steep walls left by quarrying and open pit mining through a modified form ofthe overburden casting technique. Blasting can also be applied to breaking up pit floors andbenches to speed and improve revegetation of these areas (subsoiling)."

Jan 1, 1994

By P. A. Mingione

"AEROPHINE@ 3418A is a unique sulfide mineral promoter produced by Cyanamid, based on phosphine (PH3) chemistry. It has proven effective as a collector for the sulfide minerals of copper and particularly lead (galena), as well as for secondary gold and silver values. AEROPHINE 3418A has widest application as a Cu and/or Pb collector for complex ores of Cu-Zn and Pb-Zn, which frequently have significant quantities of associated precious metal values. Advantages shown in the use of AEROPHINE 3418A are improved selectivities against Zn- and Fe-sulfides, increased precious metals recoveries, reduced total collector consumptions for Cu and/or Pb flotation, and increased flotation kinetics leading to higher recoveries of these values. Operating plant, pilot plant and laboratory test data from treating different ores are presented, demonstrating the advantages in use and preferred application of AEROPHINE 3418A.INTRODUCTIONCyanamid operates the only phosphine and phosphine derivatives plant in North America, located in Niagara Falls, Ontario. Specialty chemicals manufactured at this facility are used in many diverse applications, including solvent extraction reagents and textile flame retardants. A unique phosphine-based sulfide mineral promoter, AEROPHINE 3418A, is also produced. The origins of AEROPHINE 3418A promoter date back to the 1960's, when it was established that sulfide mineral collectors based on phosphine chemistry demonstrated efficacy. This new collector chemistry was found to provide flotation performance differing significantly from those of more traditional thiol collector chemistries such as xanthates, dithiophosphates, mercaptobenzothiazoles, thionocarbamates and those with xanthogen groups. Some of the advantages ultimately demonstrated by AEROPHINE 3418A promoter compared to these traditional collectors include:"

Jan 1, 1990

By R. M. Waterstrat

X-ray diffraction and metallographic examination of binary Mn-rich alloys with Ti revealed the presence of intermediate phases in this system. A binary R phase has been identified and also a phase having an a-Mn type structure. The X-ray pattern of the phase TiMn3 is presented and a tentative phase diagram for the Mn-rich portion of this binary system has been constndcted. MANGANESE-rich alloys with titanium have been subjected to thermal analysis at temperatures down to 1100°C by Hellawell and Hume-Rothery.1 Their results indicate the existence of an intermediate phase TiMn3 in this binary system. This phase appears to coexist with the Laves phase TiMn2, and with terminal solid solutions based on the allotropes of manganese, at least down to 1100°C. The above investigators did not attempt to determine the crystal structure of this phase, however. Since, by analogy to the binary systems Mn-V and Mn-Cr3 one might expect to find a phase in this region of the diagram, it seemed desirable to obtain X-ray diffraction patterns of alloys in the concentration range in question, in order to ascertain whether the sigma phase or related structures occur. EXPERIMENTAL PROCEDURES Alloys were prepared by arc-melting electrolytic manganese and iodide titanium in a water-cooled copper crucible under a helium atmosphere. Excess manganese was added to each melt in order to allow for losses incurred during melting. The alloys were then wrapped in molybdenum foil and sealed in evacuated quartz tubes for annealing at various temperatures, as shown in Table I, followed by quenching in cold water. Although the inside of the tubes showed evidence for some loss of manganese from the specimen during annealing, there was no evidence of any reaction between the specimen and either the molybdenum foil or the quartz tube at these temperatures. It was later found that the manganese loss was considerably reduced by annealing these alloys in sealed quartz tubes containing one atmosphere of purified argon. As an added precaution the surface of each specimen was ground off before crushing the alloys to -270 mesh powder, using a hardened steel mortar and pestle. X-ray powder patterns were obtained using either FeKa or CrKa radiation in an asymmetrical focusing camera, which gave excellent dispersion of the closely spaced lines. Pictures were also obtained using a Debye camera of 5-cm radius which provided data in the angular region not covered by the focusing camera. The alloy specimens were polished and examined metallographically, using an etchant consisting of 60 pct glycerine, 20 pct nitric acid, and 20 pct hydrofluoric acid. The 10-g buttons were in each case broken in half and found to be well-melted and free of any gross segregation. One half of certain alloy buttons was submitted to chemical analysis in the "as-cast" condition. No appreciable change in composition seemed to occur during annealing . RESULTS The X-ray pattern of alloy Ti1.17Mn0.83 was found to agree well with that of the ternary R phase which was first found in the Mo-Cr-Co system,' and re-

Jan 1, 1962

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014