Search Documents

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By M. Hertzberg

Results of a comprehensive study of the absolute spectral radiance of the infrared emissions from methane-air explosions are reported. The spectral growth of these expanding flames were recorded with a time resolution of 1 msec in the spectral range of 1.7 to 5.0 µm. Time-resolved spectra were obtained for methane-air mixtures as a function of stoichiometry, nitrogen dilution, and Halon dilution, in a 9-liter vessel under different venting conditions. Data are also presented for coal dust-air explosions. Temperatures, obtained from the absolute radiances and from a band ratio technique for methane-air, are internally consistent and are generally 50° to 200°K below adiabatic flame temperatures. All near limit mixtures gave essentially the same flame temperatures (1,500° to 1,600° K) regardless of whether the limit was obtained by dilution with excess air, excess methane, excess nitrogen, or Halon. The coal dust explosion spectrum is essentially a blackbody continuum at 1,500° K with some selective emission at 4.4 µm from hotter CO2. The data are analyzed in terms of the radiative dynamics of a sperically expanding flame zone. The importance of radiative transport is assessed. An equation is derived which relates the instantaneous fraction of combustion power radiated to adiabatic variables.

Jan 1, 1973

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight's sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By Kevin M. Connor, O&apos

This report documents-the process of literature review, site selection, instrument installation, data acquisition, and preliminary data reduction performed to evaluate the influence of rock mass discontinuities on coal mine subsidence. A system of surface, subsurface and mine level instrumentation was installed at the Armco No. 7 Mine in Montcoal, West Virginia where the overburden varied in thickness from 630 to 1040 feet. Survey monuments, borehole pressure cells, full profile borehole inclinometer-extensometers, mine level extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. Final design of the instrumentation system was based on: a) review of available information, b) field mapping and analysis of areal photography, c) drilling, and d) borehole geophysics. The report contains the complete graphed data of stress and displacements accompanying the longwall mining of a 4800 ft long by 480 ft wide coal panel.

Jan 1, 1983

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

By E Oktay, I Yusufoglu, C Kahruman

Powder and spherical pellets of MoO2 were oxidised under controlled conditions in the temperature range 674-791 K at oxygen partial pressures of 8.1-30.4 kPa. Weight increase during the reaction was determined by thermogravimetric analysis. It was concluded that the reaction is 0.6th order with respect to oxygen concentation and that the activation energy is 148 kJ/mole. In experiments conducted with powder, fast transfer of reaction heat to the gas phase created isothermal conditions, but the temperature of pellets rose by a maximum of 54 K at 674 K and 105 K at 791 K. The rise in temperature caused structural changes such as sintering and crack formation, which had a considerable effect on the reaction rate. The findings should be taken into account in the design of equipment and choice of operating conditions for roasting MoS2

Jun 21, 1905

By Douglas W. Fuerstenau

This report presents the results of an investigation of comminution in tumbling mills. Five different topics involved with ball mill and rod mill grinding kinetics were studied and the results analyzed in terms of phenomenological size reduction and transport models. Continuous rod mill grinding was found to be characterized by high Peclet numbers which permit simulation to be carried out by several methods. The dry batch ball mill grinding of mineral mixtures showed that the breakage rates of the components were composition-dependent but time-independent and were normalizable with specific energy. Locked-cycle tests on mineral mixtures showed that a grinding circuit may take a long time to attain steady-state, during which time the composition of the mill holdings, and hence the breakage rates of the components, continuously changed. This study revealed that under plant conditions, grinding circuits can be in transience perpetually. The transport of mineral mixtures through drums was found to exhibit complex size and/or density-dependent segregation. However, the grinding media in a ball mill can eliminate such segregation, thereby simplifying the modeling of the continuous grinding of complex feeds. Wet batch rod mill grinding on single minerals divulged that the normalizability of breakage kinetics is valid for slurries of constant pulp density at different hold-ups but cannot be extended to slurries varying in pulp density.

Jan 1, 1983

By K. K. Kelley

Thermodynamics data for silicates have applications in the fields of extractive metallurgy, ceramics, and geochemistry. To facilitate these applications, up-to-date tables of heats and free energies of formation are needed. It is the purpose of this report to supply such tables for anhydrous silicates. During the last 15 years the heats of formation of a substantial number of anhydrous silicates have been reliably determined at or near room temperature. This resulted from the development (first by the Bureau of Mines and later by the Geophysical Laboratory of the Carnegie Institution of Washington, by the Institute of Geology of the University of Helsinki, Finland, and by the Department of Geology of the University of Chicago) of accurate solution calorimeters, employing hydrofluoric acid as the reaction medium. Specific references to work of these laboratories will be made in the next section of this report. Also, entropy data at 298.150 K. and high-temperature heat-content values are available for many of these silicates, mainly owing to work of the Bureau of Mines. Most of these entropy and heat-content data have been compiled in Bureau of Mines Bulletins (13, 15).3

Jan 1, 1962

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

By Richard Rice

TURBO blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting. FIG. 1.-STEAM TURBINE DIRECT CONNECTED TO AIR COMPRESSOR. The first blast-furnace blowing engine of this type to be installed in America was built by the General Electric Co. and is installed at the oxford Furnace of the Empire Iron & Steel Co. This machine was put into operation March 8, 191.0. A duplicate unit is situated at the furnace of the Northern Iron Co. at Port Henry, N. Y., which unit was put into opera ion June 30, 1910 (Fig. 1).

Jan 5, 1914

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.