Search Documents

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

Rb-Sr measurements on total-rock samples of granitic rocks from the Mount Isa region have confirmed the existence of two periods of granite-forming activity. The Kalkadoon Granite, together with the Ewen Granite and possibly an older phase of the Sybella Granite, has been shown to belong to the earlier age-group at 1760 m.y.; the Wimberu Granite and a pegmatite associated with the Sybella Granite have been dated at 1540 m.y. The initial Sr ratio suggests that the Wimberu Granite may be new material of deep-seated origin.Further Rb-Sr measurements have confirmed previously-reported K-Ar results upon biotites from these rocks, whilst showing that, in this metamorphic terrain, biotites have lost varying amounts of radiogenic Sr and Ar, and therefore yield ages which are younger than the true age of the second event.

Jan 1, 1966

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By Linda L. Chasko, Charles P. Lazzara, Gary Braselton, Ronald S. Conti

Preparedness is an important element of any underground mine's strategic plan in dealing with an unexpected event, such as a fire. A fully implemented fire preparedness and response plan is essential in reducing the probability and seriousness of a mine fire. This report describes the development of an underground coal mine fire preparedness and response checklist (MFPRC). The checklist is a data collection instrument for profiling both the fire prevention and response capabilities of a mine site and usually requires 3 to 4 days to complete. The checklist encompasses conditions, procedures, and equipment that have frequently been identified as the primary or contributing causes of underground coal mine fires. At least 1 day is needed underground to evaluate the water system. This entails measurements of water flows and pressures at fire hydrants, and water throw distances of fire hose and nozzles at several locations (mains and branch lines). A few of the other topics that are discussed with mine personnel include detection and suppression systems, combustible materials, mine rescue and fire brigades, and firefighting equipment. The MFPRC was developed by the National Institute for Occupational Safety and Health (NIOSH),Pittsburgh Research Laboratory. Under a Cooperative Research and Development Agreement (CRADA) with Cyprus Amax, Twenty mile Coal Co. (Oak Creek, CO), the checklist was field tested and further refined. Additional field tests were conducted at several other operating coal mines.

Jan 1, 2000

By K. W. Lee, C. Pound, J. Carmody, L. Petersen, C. Nelson, J. G. Cai

The feasibility of developing the Underground Science City below the Kent Ridge Park has been investigated. The primary aim of the study has been to explore the possibility of creating underground space to house a new community of research laboratories and offices. The investigation represents the first such study undertaken in Singapore for a non-military underground facility. The paper describes the geology of the Underground Science City site and illustrates the layout and plan of the Underground Science City. The geology and rock mass below the Kent Ridge Park is generally favorable for the development of an underground cavern complex. Underground Science City can be potentially developed housed in a cavern complex. Several potential development schemes are studied; with various combination of deep/shallow mined caverns of different span sizes and access options. The preferred scheme is shallow, mined room-and-pillar caverns with large spans and shaft accesses at both existing surface Science Park 1 and Science Park 2. The scheme can be potentially expanded laterally to create more underground space for new Underground Science Cities at Kent Ridge area.

Jan 1, 2001

By Jean G. Fortin

The manufacturers' proposed technology has been a key factor in selecting production, mobile and fixed equipment in order to achieve the targets set in our 2026 mining plan. This paper will present an overview of the most recent technologies adopted by Québec Cartier Mining Company for communications, power supply, dewatering, drilling, loading, hauling and processing. All these new technologies contribute to the improvement of our day to day operations while operating with a state of the art asset reliability program.

May 1, 2007

By José A. Rios, José A. Vidalôn

The case study of a highland area in the Central Andes of Peru, where many abandoned polymetallic mines are found, is presented. Some of these mines generate metal leaching and acid rock drainage (ML/ARD) or have potentially ARD generating (PAG) tailings/waste rock storage. Effluents are discharged into the first of two lakes in line, which act as reservoirs for irrigating an important valley in the desert coastal region. Drainage fees, their relationship with the deposit and the solid-wastes mineralogy are discussed, as well as variations in water and sediments composition, the benthos, and the aquatic/riparian flora/fauna in these lakes.

Jan 1, 2000

By Paul Downing

Identity Theft Outline • What Are MY Chances??? • Types Of Thefts • Sources Of Theft Info • Stolen Identity vs. Background Checks • Information/Data Safeguards • Corporate Data Handling • Reclaiming Your Identity • Monitoring Your Identity

Jan 1, 2006

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

The inherently explosion-proof mine (EPM) concept is based upon the non-flammability of certain combustible-oxidant-inert gas mixtures, and the effect of partial pressure of gases on physiological reactions. In a properly controlled underground environment, gas explosions are impossible, men can do work, and relatively high concentrations of methane would be permitted. A systems analysis has been performed to examine the physiological, engineering, and economic feasibility of such a concept, and methods and equipment are recommended for maintaining an EPM atmosphere in a bituminous coal mine producing a nominal two million tons of clean coal per year. It is concluded that: engineering feasibility can be demonstrated using subsystems and components that can be designed and built within the present state-of-the-art, that economic feasibility is possible within approximately five years, and that physiological feasibility is sufficiently promising to warrant continued investigation.

Jan 1, 2012

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By Thierry Bernard, J. M. Laboz

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications

Jan 1, 2000

THE object of this paper is to review certain features in connection with the mining of narrow lodes, say up to 20 ft. or so wide. The types of ore-body to which it is intended to refer are those which occur. chiefly as fissure or shear-Iodes-that is, those lodes which are to be found in belts of country which have been subjected to dynamic stresses, resulting in the formation of cracks and fissures, into some of which has been concentrated sufficient metal-bearing material to form ores. Very frequently one of the walls of such a lode is found to be a fault, or plane of differential movement.The first point which comes up for consideration is the shaft and its position. From the information afforded by the prospecting which has been done on a lode relative to the dip, nature of country, &c., the position of the main hauling shaft can be determined. For purposes of general utility the hangingwall is generally chosen, if a vertical shaft, though, on account of freedom from creeps, the foot-wall would be safer. Vertical shafts are preferable to underlie shafts in many ways; but wherethe lode maintains a flat dip the cost of cross-cutting at the various levels becomes very heavy'. This difficulty may to some extent be modified· by sinking a vertical shaft in the hanging-wall...

Jan 1, 1912

By Donald A. Bruce

Pregrouting is an extremely important part of many rock tunneling projects. However, poor and unsatisfactory performances have been frequently recorded often with very severe consequences, technically and financially. This paper, based on personal knowledge of several relevant case histories, provides recommendations with respect to specification drafting, drilling, water pressure testing, and grouting methodologies, and cementitious grout mix design principles. Even given that the logistical challenges facing tunnel pregrouting from underground will prevent all the sophistication and innovations of contemporary dam foundation grouting being practically implemented, there is still opportunity and need to change “traditional” approaches.

Jan 1, 2005

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009