Search Documents

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By J L. Mauk

Gladstone Hill, a volcanic-hosted low-sulfidation epithermal prospect in the Coromandel Peninsula, is less than 1 km from the world-class Martha Hill Au-Ag deposit. Gold-silver-bearing quartz veins occur in Late Miocene andesitic volcanic rocks of the Waipupu Formation that are extensively altered. The occurrence, spatial distribution and temporal relationships of hydrothermal minerals have been determined along two cross sections that transect the Amaranth, Gladstone, Cowshed and Moonlight veins. Quartz and pyrite are ubiquitous along these sections. Adularia and chlorite are widespread, but both are scarce in wall rocks adjacent to the Moonlight and Cowshed veins. By contrast, rare hydrothermal albite and epidote are restricted to wall rocks surrounding the Amaranth vein. Illite, which replaces adularia, is widespread and grades laterally eastwards into a zone of interstratified illite-smectite that envelops the Moonlight and Cowshed veins. During late-stage hydrothermal activity, rare calcite formed at depth and uncommon kaolinite and alunite formed at shallow levels. The overall clay mineral zonation with illite grading eastward into interstratified illite-smectite reflects paleothermal gradients of >220¦C to -170¦C towards the margin. The alteration assemblage of quartz, adularia, chlorite, albite, epidote, illite, interstratified illite-smectite and pyrite reflects formation from a near-neutral to weakly alkaline pH chloride water that contained low concentrations of CO2, Late calcite formed from very local descending steam-heated CO2rich water, whereas the rare assemblage of kaolinite and alunite formed from shallow steam-heated acid-sulfate water. Analysis of the available data indicates that the Martha Hill deposit and the Gladstone Hill area formed within a single large geothermal system. We infer that the Martha Hill deposit formed in the main upflow zone, whereas the Gladstone Hill area may have formed adjacent to this upflow zone.

Jan 1, 2001

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978-September 30, 1979) under its Mine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By D. F. Cooper, J. G. Paterson, K. H. Pang

"Effective control of metallurgy by manual adjustment of cell levels is common flotation practice. With an on-stream XRF analyzer interfaced to a process control computer it is possible to program the computer to carry out this function automatically. This paper describes the development and implementation of closed loop control of the concentrate and tailing grades at the Clarabelle Mill of the International Nickel Company of Canada, Limited, The XRF analyzer was used as the sensor, cell level as the control and the computer as the controller.IntroductionThe International Nickel Company of Canada, Limited recently brought on-stream Clarabelle Mill having a rated capacity of 35,000 tons per day. The plant was required to increase milling capacity in the Sudbury area by 9,000 tons per day and to improve milling efficiencies by replacing the obsolete crushing and grinding equipment at the Copper Cliff Mill. This represents the fourth mill built since 1959 and incorporates the latest thinking in a continuing evolution of instrumentation and control concepts. Table 1 illustrates control progress at Inco since 1959.In 1967 Frood-Stobie Mill came on-stream incorporating a central control room, an on-stream analyzer, a data gathering computer, and a significant change in instrumentation from direct-contacted pneumatic to miniature electronic. The computer successfully controls the analyzer but has very limited process control capability. Based on this experience a process control computer system was installed at Clarabelle Mill with the objective of carrying out extensive supervisory control and a limited amount of direct digital control."

Jan 1, 1973

By John G. Parker

Important quantities of gold, silver, platinum-group metals, selenium, tellurium, and arsenic are recovered in the processing of copper concentrates. The objective of this Bureau of Mines study was to determine the occurrence of these elements in copper ores and to trace their distribution during subsequent processing steps. The study describes the important areas supplying concentrates, precipitates, and unrefined copper to the copper smelting and refining industry in a composite of the years 1971-74. The relative importance of these areas as a source of the respective byproducts is assessed. The lack of certain quantitative and assay data, recycling of dusts and slags, and the addition of scrap to the feed often complicates calculations and estimations of the byproducts in the smelter-refinery throughputs. Such volatile or low-boiling point elements as arsenic, selenium, and tellurium may be lost in gaseous and other emissions in various processing stages, or they may be concentrated in slags and residues for which samples were not available. The effects of antipollution legislation to improve control of sulfurous and other emissions that may affect recovery of certain byproducts was noted. A section on newer technology illustrating hydro-metallurgical techniques that may affect the recovery of minor metals is included.

Jan 1, 1978

By R. Filippone, Donald Leroux, Colin Hardie, G. Leichtle, Cesar Gomez, Jim A. Finch

"Bubble surface area flux (Sb) is the surface area of bubbles per unit time per unit cross-sectional area of flotation machine. The units are: (m2 bubble surface/s)/(m2 cell) or s -1. For bubbles of mean size db (m), s b = 6-Qg/A db where Qg is the gas rate (m3/s), and A the cell cross-section (m'). This parameter is now receiving wide attention as the possible key machine variable in flotation diagnosis and modelling. The concept is described and the potential use of sb is illustrated by work on flotation columns and mechanical cells. In column flotation of recycled paper, the dependence of ink recovery on s b was the same regardless of size of column or type of sparger. In mechanical cells, it has been established that the rate constant is related to Sb independent of impeller type.The use of s b is limited by the problem of measurement, primarily that of estimating db. A prototype probe designed to estimate db (and hence sb) based on conductivity measurements is described. Exploratory work with the probe in a mechanical cell suggests the promise of making estimation of s b routine.INTRODUCTIONFlotation is the result of interaction among variables associated with the feed particles, chemistry and the machine (flotation cell). Trying to isolate the effects of each aids in process diagnosis and is at the centre of attempts to model flotation. The machine variables that have been investigated include the air flow number, the power number and specific power (Harris, 1976). None have survived as the basis for predicting flotation response perhaps because they did not include directly the properties of the bubble swarm (or dispersion). Recently, Gorain (1 997) explored the relationship between the flotation rate constant and various ""gas dispersion"" parameters notably: superficial air rate (Jg = Qg/A, where Qg is the volumetric gas rate and A is cross-sectional area of cell), bubble size (db), gas holdup (Eg, i.e., the volumetric fraction of a cell occupied by gas) and bubble surface area flux (sb = 6.Jg/db). Of them all, Gorain et al. (1997) conclude that the latter, the surface area flux, correlated best with the flotation rate constant. This concept was adopted from column flotation where it was used to estimate, among other factors, the maximum amount of gas that could be injected (Finch and Dobby), 1990). Let's start by reviewing the concept. Following that some examples of where the concept has been applied will be described to illustrate the current interest and finally we will consider how to measure the surface area flux."

Jan 1, 1999

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By Horace C. Porter, F. K. OVITZ

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantitieS', a series . of tests was begun in the fall of 1909 under the supervision of tT. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for exaIp.ple, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New R~ver (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a fu11 account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included. The tests of New River coal, in cooperation with the Navy Department, were undertaken to determine the advantage to be gained by storing coal under water, and particularly under salt water. Small lots were used in order to make the tests of maximum severity, and parallel experiments were made with run-of-mine and crushed coal under one-fourth inch size. All of the small lots tested under the different conditions (except those tested near Key West, Fla.) were taken as representative portions from one large original lot. The tests of Pocahontas coal, which, like the New River, is semibituminous, were undertaken chiefly to determine th.e effect of the tropical conditions in Panama. They were made on an outdoor pile of 100 tons of run-of-mine coal. Pittsburgh gas coal, a high-volatile, bituminous type used at gas and by-product coke works, was exposed for test at Ann Arbor, Mich., in cooperation with the University of Michigan. The university agreed to make tests at successive intervals of storage to determine, in its illuminating-gas experiment station, the yields of gas and byproducts from the coal. The coal, screened lump, was stored in about 4-ton lots out of doors in open bins. Subbituminous coal, which is mined in Colorado, Wyoming, and other States, and is known also as "black lignite," is commonly supposed to deteriorate rapidly in storage, especially by "slacking" or crumbling of the lumps. The tests herein described were undertaken at Sheridan, Wyo., in cooperation with the Chicago, Burlington & Quincy Railroad Co., in order to determine the extent of this slacking and the accompanying loss of heat value. The tests were in open bins holding 4 to 12 tons.

Jan 1, 1917

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption if this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 mill ion tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably are in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

Iron Ore - Mineral Processing Overview Several years of iron ore price increases, coupled with a period of strong global demand for raw materials, presented iron and steel producers with unprecedented costs and difficulty procuring the demanded high quantities of iron ore. These conditions spurred many companies to investigate new ore bodies and also reassess past decisions (such as divestment of captive iron ore mines that ensured dedicated supply or a move to reliance on the 'spot market' instead of long term contracts with suppliers) and revisit alternative sources of iron units, including low grade deposits, tailings reprocessing, Ti-rich ores, and iron sands. To properly upgrade these iron sources requires a complete battery of mineral processing techniques. Within different regions around the world, operations and technology have developed to specifically beneficiate the local ore bodies. This paper attempts to bring these different general processing techniques together to allow insight into various common and proven methods of iron ore beneficiation. This paper further explores the current trend to develop global iron ore reserves, and discusses the methods to beneficiate and successfully reduce and smelt iron ore using Outotec's physical separation, direct reduction and smelting technologies for final production of pig iron and slag. Use of these various technologies may allow treatment of what was typically considered a tailings stream into a profitable product.

Sep 13, 2010

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By Frederick H. Raab

An electromagnetic (EM) system for the location of trapped mine workers at coal-mine (300 m) depths has been developed. The use of such a system in deep mines (1-km depth) requires transmission at extremely low frequencies (ELF) and a reduction in the effective noise level beyond that which can be obtained by acceptable Integration times. Automatic-noise-cancellation (ANC) techniques reduce the effective noise level by combining several received signals that contain correlated noise. Such signals can be obtained either from a remote magnetic antenna or a local electric antenna. During Phase III of this program, real ELF noise data were acquired and used to test the ANC algorithms developed during Phase II. The ELF noise data were obtained from analog recordings made by Develco under another Bureau-of-Mines contract. Digitization was accomplished by an ND converter that was added to a GMRR computer. Phase III tasks Included preparation of software for digitization, computer-computer communication, data processing, and statistical analysis. Useable data were obtained from eleven half-hour tapes containing noise from one axis of the primary antenna and three axes of the remote antenna. The overall average Improvement in SNR was 4.1 dB. However, the average Improvements for the Individual X, Y, and Z axes were 4.2, 11.9, and -1.9 dB, which roughly follow the observed noise power. Nonlinear processing was not effective with this noise.

Jan 2, 1984

By V Poizat

In different parts of the world the term epithermal is commonly used for a variety of deposit styles. Using the redox state of the ore-forming fluid (inferred from mineralogy and alteration), the metal assemblage of deposits, and other characteristics, at least five different styles of epithermal deposit can be distinguished. Most of these different deposit styles appear to be related to magmatic fluids, with differences resulting from different compositions of source magmas. The most common style of epithermal deposit (low-sulfidation gold-silver deposits associated with calc-alkaline volcanic rocks) remains the most difficult to explain; the metals in these deposits may be derived by basement leaching without magmatic input, or they may come from magmatic volatiles, with contaminated I-type or S-type magmas as the most likely source.

Jan 1, 1995

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961