Search Documents

By R. D. Yancich

A case study of longwall mining surface subsidence was performed at a mine in Southwestern Pennsylvania. The mine operated in the Pittsburgh coal seam which averaged 70-72 inches with 6-8 inches draw slate in the longwall location. The average overburden depth ranged from 625 8eet to 660 feet. Three adjacent longwall panels were studied and classified as Panel 1, Panel 2, and Panel 3. The following is information on each and can be seen on the General Mine Map (Fig. 1).

Jan 1, 1984

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By G B. Arehart, S J. Mathews, J L. Mauk

The banded nature of the quartz veins which form the Empire lode at the Golden Cross mine, is perhaps their most striking feature. Petrographic studies show that significant differences occur between the bands in terms of textures, quartz grain size, calcite, adularia and kaolinite content, and the form, concentration and mineralogy of sulfide phases.   The d18Oquartz values of individual bands within the vein material range from 7.3-10.9ë. Calculations show that the d18Oquartz values can be adequately explained by temporal variations in the system temperature, boiling and/or variations in the systems fluid/rock ratios.

Jan 1, 1995

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992

By Blanchard R

The discussion submitted by Drs. Stillwell and Edwards is at once helpful and gratifying to the authors. Their contribution deals with two phases of the problem-(I) an additional suggestion for the relative solubility of galena and marmatite, and (2) submission of an alternative explanation for the greater leaching of the Northern ore-body. With the first we agree in principle, and herewith present recent data which will help to substantiate the idea, though the mechanism is not believed to be as simple as indicated by Stillwell and Edwards. Concerning the second suggestion, the original explanation put forward. in the paper is held to fit the facts more closely.In view of the influence, as shown by Garrells' paper,in which the presence of Cl' ion may have upon the relative solubilities of lead and zinc, it is perhaps worth noting that Broken Hill mine water carries a higher content of Cl' than has been reported from many of the other lead-zinc districts.Since our paper was published, an analysis of water issuing from the newly-opened Northern ore-body on the 2,600-ft. level has been made (12/1/43). It is compared with that quoted in the original paper as follows:

Jan 1, 1943

By W. M. Shaver, W. R. Dengler, F. A. Edwards

INTRODUCTION The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounzes per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required three lift hoisting for men, materials and ore. I n addition to the increased travel time and ore handling expense, increased humidity and temperature and ventilation and compressed air losses have added to the inefficiency of the operations. As a result, studies were initiated in 1980 to assess the future of the Macassa operation.

Jan 1, 1985

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By B Chi, A Mahanta, R A. M Maddever, O Dominguez

BHP Billiton, in collaboration with Sodern and CSIRO, has developed a downhole logging tool for measuring geochemistry in situ. The FastGradeTM 100 (alternatively, FG100), exploits pulsed fast and thermal neutron analysis (PFTNA) to analyse the rock. This method is based on the detection and measurement of characteristic gamma rays emitted from isotopes in the material that become briefly radioactive when they are bombarded with neutrons. The tool outputs raw spectra arising from three types of neutron interaction, namely, inelastic scattering, neutron capture and neutron activation, which occur in successive time-windows (Smith et al, 2015). The spectra contain peaks at specific energies that are characteristic of the different elements interacting with the neutrons, the gamma count of which is related to elemental concentration. BHP Billiton uses in-house data processing software to convert the measured spectra to elemental concentrations.Much work has been done to understand the tool response under a wide variety of environmental and operating conditions, including logging speed, borehole rugosity, the presence of cavities, water etc. Effort has also been directed at understanding and quantifying the current sources of error in our conventional assays due to sample collection, preparation, and laboratory instrumentation in order to use this information as a baseline to compare against the FastGradeTM 100 results.To date, the FastGradeTM 100 primary use has been as a verification tool (JORC, 2012). However, beyond this, it has considerable potential to improve productivity in both exploration and production environments due to its ability to provide geologists with assay results soon after a hole is drilled.This paper presents initial test work and tool performance, including accuracy and precision under various conditions. Results are illustrated by comparing tool measurements to assays from laboratory samples collected from both reverse circulation and diamond-drilled holes.CITATION:Chi, B, Maddever, R A M, Mahanta, A and Dominguez, O, 2017. Near real-time assay with downhole assay tool (FastGrade™ 100), in Proceedings Eighth World Conference on Sampling and Blending , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Your thoughts on the current status of the global minerals industries? The global economic, technological, social and political changes of the last two decades of the 20th century resulted in the emergence of a restructured minerals industry. This industry is now based on a new cost-cutting philosophy; utilization of modern technology; productivity gains rather than production tonnages; diversification of mineral markets; and globalization of exploration, mining and processing. Quantity and tons used to be the focus. The emphasis today is on remaining competitive in the marketplace by lowering per-unit production costs as much as possible. What factors and trends will impact the minerals industries in this, the 21st century? A number of parameters will impact minerals operations and shape the future sustainability and growth of the minerals industries. Increased demand for minerals will be accompanied by the demand for technical advancements. We will also see a continued emphasis on health and safety, environmental stewardship, and education and training. Let me elaborate.

Jan 1, 2002

By B. M. Larsen, J. W. Campbell

Several articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken temperatures in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the subject and was also used by the writers. Previous Investigations In 1916, Burgess' made perhaps the first systematic series of measurements in steel furnaces. The emissivity figures of 0.40 for liquid steel and of 0.53 to 0.65 for liquid slags had been determined by the Bureau of Standards and were used by Burgess in this work. These correction factors are still being used and are regarded as fairly accurate, so that the tapping and teeming temperatures on metal streams given by Burgess should be very nearly correct. Most of his temperatures of furnace roofs and slag surfaces were taken while flames were present in the furnaces and include a few roof temperatures above 1700' C. (3100' F.).

Jan 1, 1927

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By M. M. Gadde

Recent regulatory changes in the United States make it mandatory to conduct structural analysis of coal mine seals used to isolate abandoned workings from active mining areas. Different loading criteria are available for seal design depending on whether gob composition is actively monitored and maintained or not and whether the gob conditions lead to deflagration or detonation type loading. Since the loads involved in seal designs are dynamic in nature, the structural analysis must be made using dynamic stress analysis techniques. However, because of the significant complexities involved in conducting dynamic analyses, some designers use approximate simplified techniques to address the design problem. In this paper two such simplified methods are critically evaluated for their suitability to design coal mine seals. The benefits and limitations of the simplified methods are also outlined. Some comparisons are made to show the differences between sophisticated three dimensional dynamic analyses and the simplified methods and to delineate the problems associated with the latter approaches.

Jan 1, 2009

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995