Search Documents

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By C. Rutter, N. SHEA, K. KOLOBE

Henderson Mine’s primary production transitioned from the main portion of the 7700 level to the 7210 main panel in 2005. On the 7700 level, the southwest (SW) panel was brought into production in 2014 and produced through 2020. A-Panel was brought online in 2019 and took over primary production in 2020. The 7210 north panel is under development with production expected to commence in 2025. The 7700 northwest panel is expected to be the mine’s last production panel.

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By Moacir Kuwahara

Nesta pesquisa, foi desenvolvido um material compósito com matriz poliéster, reforçadas com fibras de bambu e de sisal. As fibras de bambu foram extraídas do próprio campus da UFPA e as fibras de sisal obtidas no comércio de Belém. As fibras foram submetidas ao equipamento moinho granulador, com a finalidade de otimizar o corte das fibras, visto que, pelo processo manual gasta-se um certo tempo para obter uma quantidade necessária, para fabricação dos compósitos. E os comprimentos obtidos variaram entre 5 a 15 mm. Os compósitos foram produzidos utilizando-se o menor nível possível de processamento tecnológico nas etapas de fabricação. Foram fabricados 8 (oito) corpos de prova para fração mássica definida com a seguinte proporção 3,90%; a fabricação foi realizada por moldagem manual, usando resina poliéster insaturada com a proporção de agente de cura/resina de 0,33%. As fibras de sisal e bambu foram submetidas a ensaio de tração, determinação da massa especifica e avaliação microestrutural, por microscopia eletrônica de varredura (MEV).

Aug 16, 2017

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By Y. C. Kim, F. Szidarovszky

G.M. Philip and D.F. Watson The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write : "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accu¬mulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common. ? References Journel, A.G., 1986, "Geostatistics: models and tools for Earth Sciences," Journal of Mathematical Geology, Vol. 18, No. 1, pp. 119-139. Philip, G.M., and Watson, D.F., 1985a, "Theoretical aspects of grade-tonnage calculations," International Journal of Mining and Geological Engineering, Vol. 3, pp. 149-154. Philip, G.M., and Watson, D.F., 1985b, "A deterministic approach to computing ore reserves. I, Grade Estimation," Earth Resources Foundation, Occas. Paper 2, The University of Sydney, 24 pp. Philip, G.M., and Watson, D.F., 1987a, "Neighborhood discontinuities in bivariate interpolation of scattered observations," Mathematical Geology, Vol. 18, No. 1, pp. 69-74. Philip, G.M., and Watson, D.F., 1987b, "Estimating interactions of topological functions," Mathematical Geology, Vol. 18, (at press). Reply by Y. C. Kim Before replying to the comments by Philip and Watson, it is desirable to establish the original perspective of our paper, which was intended primarily for the practitioners of mining who possess a working knowledge of ordinary kriging. The paper tried to convey the following practical points: (1) there are circumstances in which one observes negative weights, (2) illustration of circumstances under which one can expect negative weights, (3) should one obtain a negative estimated grade, one can resort to elimination of negative weights using the technique outlined in the paper, and (4) one could normally select only the first layer of surrounding assays to estimate the block grade. Under such a perspective, most of the comments by Philip and Watson are irrelevant and misdirected. For example, the practitioners do not find it difficult to "interpret" the results of ordinary kriging, as evidenced by the fact that they have been using the results for nearly a decade. Nor are the practitioners concerned with discontinuities in estimated block grades due to changing neighborhood of assays during kriging. What matters to the practitioners is the fact that kriging does provide the best estimate among all the estimation tools available to them as of today. ?

Jan 2, 1987

By R. T. McAndrew

Introduction Drinnan is situated in the Prairie Creek coal area in the Foothills belt of Alberta. It lies on the main line of the Canadian National railway from Edmonton to Jasper. The exact location is shown on the map (Figure I). Interest in the field was aroused by several circumstances: Its proximity to Brule and Pocahontas on the southwest and to Coal-spur on the southeast led to the belief that coal might be economically produced here. There was already at Hinton a 3 ft. 9 in. coal seam being mined by Seabolt. The coal was of very good grade, being black and shiny in appearance with well defined cleavage and a heat value of 12,000 B. t.u. Outcrops of coal had also been noticed on the north side of the Athabaska river and Fish creek. These facts led the Jasper Coal Company to investigate the field. This Company considered taking over the Seabolt property at Hinton, but, owing to the size of the seam, this plan was abandoned and prospecting by diamond drills and test pits was started two years ago in the district east of Hinton. After prospecting had been completed, the most favourable district was found to be in township 51, ranges 24 and 25, west of the 5th meridian. The Company's lease includes all or parts of sections 18, 19, 20, and 28 in range 24, and sections 10, 11, 12, 13, and 14 in range 25. The approximate boundaries of the property are the Canadian National railway on the north, Happy creek on the west, and Cache Percotte creek on the east. The lease comprises 3,100 acres, and the total amount of coal in sight is estimated at 100,000,000 tons.

Jan 1, 1931

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By G. F. Doggett

In describing accounting methods at Lake Shore Mines, it is the intention of the writer to limit the discussion to the principal features of the system used in securing cost figures and other statistics. The subject can be conveniently treated under the following divisions: (1) Time-keeping and Labour Distribution (2) Supplies: Handling and Distribution (3) Method of Assembling Data for Cost Purposes (4) Details of Operating Costs Time-Keeping and Labour Distribution After a new employee has gone through the routine of being 'hired on', he is assigned an employment number corresponding with the group applying to his occupation. This is for identification purposes in the plant and time office. He is also given an individual serial number, the use of which will be refer-red to later. On entering and leaving the plant, each employee passes through the clock room adjoining the time office, where he registers the time in and out on time recorders, on the clock card (Figure 1) bearing his name and number. It is the duty each morning of the time clerk to extend the hours worked by each employee, as indicated by the clock for the previous day, and at the end of the half-month period the total hours are multiplied by the rate and entered in the space provided for total wages at the bottom of the card.

Jan 1, 1935

By Breno Totti Maia

A aciaria 1 da Usiminas Ipatinga é composta por 03 convertedores BOF e uso de ventaneiras para promover a melhor mistura do banho. No intuito de garantir e melhorar a estabilidade operacional da etapa sopro na produção, foi iniciado uma séria de desenvolvimentos na lança de oxigênio através da aplicação da tecnologia Slagless® com objetivos de melhorar a formação de escória, evitar cascão de lança, evitar cascão no sistema OG (recuperação de gases) e aumentar a disponibilidade de lanças através do aumento de sua vida. Os resultados apresentados são extremamente favoráveis, pois após a implementação da tecnologia, todos os objetivos foram atingidos associado com uma vida extremamente elevada do bico de lança, agora chamado cartucho, garantindo estabilidade e conforto operacional para a equipe da aciaria 1 da Usiminas Ipatinga.

Aug 15, 2017

By Ashley Woodward, S. Katharine Hammond, Mayela Padilla-Salas

This paper presents a scalable framework for worker safety assessments. The paper focuses on uranium mine reclamation in underserved communities, specifically Cove Chapter of the Navajo Nation. By integrating field observations, OSHA data analysis, systems mapping, and a hierarchical occupational health pyramid, this framework identifies site-specific hazards while addressing broader socio-cultural dynamics. The approach improves upon existing safety programs by suggesting actionable, locally sensitive solutions that prioritize higher-order controls such as hazard engineering interventions and administrative controls. This study contributes to enhanced worker safety, efficient environmental restoration, and engagement in marginalized communities with abandoned mine lands.

Feb 22, 2026

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By Mauro Araújo Medeiros

Os aços inoxidáveis dupex tem sido largamente empregado em vários setores da industria principalmente em virtude da sua boa combinação entre suas propriedades mecânicas e resistência a corrosão. Um aço inoxidável duplex DIN W. Nr. 14462 foi submetido a ensaios de torção a quente com taxas de deformação de 0,3; 0,5; 1; 3 e 5 s-1 a temperaturas que variou entre 1.000 e 1.150°C. As amostras deformadas foram analisas através de microscopia ótica. As configurações das curvas de escoamento plástico foram analisadas em termos dos parâmetros de fluxo localizado como um mecanismo de acomodação da deformação durante a torção a quente. As microestruturas reveladas mostraram que o comportamento plástico do material é influenciado pela disposição inicial das partículas de austenita na matriz ferrítica e a queda de tensão após o pico esta relacionada à ocorrência de fluxo localizado na matriz ferrítica associado à fragmentação das partículas de austenita durante o processamento, bem como aos fenômenos de recuperação e recristalização dinâmica, típicos dos aços inoxidáveis duplex.

Aug 8, 2018

By Luis Romero, Edilberto Linares, Steve Windle

El yacimiento de Zafranal —proyecto de pórfidos de cobre y oro ubicado en la región Arequipa, Perú— en sí mismo ha penetrado en lo que parece ser un salto dextral sobre una estructura del SFIC. A nivel de yacimiento, se ha mapeado una serie de fallas pronunciadas WNW en la zona mineralizada principal, consistentes con la transtensión dextral inferida. Esta estructura de fallas se trazó en 3-D a partir de las zonas de gubias identificadas en la fotografía de testigos, método que permitió elaborar un modelo estructural de forma rápida y con consistencia interna. La cinemática de las vetas y los patrones de afloramiento trazados generalmente coinciden con las estructuras interpretadas. El movimiento dextral inferido en el SFIC en el Cretácico Superior es consistente con un vector de convergencia de placas hacia el norte, y puede ser utilizado para identificar targets estructurales para sistemas de edad similar, tanto en el piamonte como en la cordillera.

Dec 31, 2019

By W. H. Tomlinson

One of the more important functions of the Federal Bureau of Mines is conservation of the life and health of employees of the mineral and allied industries. Since its very beginning the Bureau has encouraged competition between mine rescue and first-aid teams as a means of stimulating interest in safety and accident-prevention work. In addition to sponsoring competition on a national and international scale during the past 45 years, the Bureau has also assisted State mining departments, mining companies, and mining organizations in holding State, district, company, and other local meets. This assistance includes providing instructors to train teams, judges, and other contest officials. The Bureau has also furnished problems and outlines for working them, judges I discount sheets (scorecards), contest rules, and problem judges. In fact, Bureau representatives participate in nearly all State, district, and company contests and have bad complete charge of some contests.

Jan 1, 1956

By C. Siac

"It is a widely held view that in the 21st century, the mining industry will be dominated by a relatively small number of large companies, truly global in scope and internationally staffed (Gooding, 1997). Interestingly enough, most of the exploration and exploitation activities are being carried out by junior and major mining companies from common law jurisdictions in civil law countries, in particular in Latin America, where in recent years, the region has ranked first as a destination for exploration dollars, thanks to the reforms undertaken by some countries to amend their legal framework to attract foreign investment. From a lawyer’s point of view, this is where the main challenge lies: how to bridge the gap between the two legal systems.In order to avoid pitfalls, common law lawyers should be more diligent and proactive when dealing with civil law jurisdictions, given the different systems of law, standards, traditions and customs. Common law lawyers cannot be expected to be well-versed in civil law but they should not be completely unfamiliar with it either. A balance should be struck to ensure clients’ needs are professionally taken care of and that common law requirements and standards are met."

Jan 1, 2003

By R. Clark Lantz, Charles Stanley, David E. Hinton

Morphometric examination of lung alterations following exposure to toxic and pathogenic substances is invaluable in detecting subtle changes which might otherwise be overlooked. Results, from evaluation of initial structural alterations, support and guide subsequent nonmorphological techniques and, when coupled appropriately, can lead to a better understanding of the pathogenesis of a disease. Morphometry is a technique which can be used to determine, quantitatively, the site, extent, development, and progression of a disease state. Determination of the extent of tissue and cellular involvement in the response to inhalation of silica has been performed in order to gain a better understanding of the development of fibrosis following inhalation of this toxicant. In addition, since silica has been postulated as one of the important pathogenic minerals in coal mine dust' it is important to understand the lung tissue response to silica prior to evaluating the effects of inhaled coal mine dusts. Male Syrian golden hamsters were placed in Hazelton 1000 inhalation chambers and were exposed to either filtered air (controls, n = 24) or filtered air plus 30 mg!m3 silica (Min-U-Si110,95%ofparticles < 5 um,n =24)for16hours per day, five days per week, for two weeks. Animals were returned to the animal quarters prior to subsequent tissue processing at 1, 4, and 12 weeks following exposure. This schedule was designed to allow time for the development of fibrosis. Lungs were fixed by intratracheal perfusion of ½ strength Karnovsky's fixative at a pressure of 20 cm H20 and tissues were taken for embedment and analysis at the light level. Determination of site, extent, and development of alterations was performed using a multitiered approach. Changes in large structures (airways, blood vessels) was determined prior to evaluation of changes at the septal tissue level. Data will be presented outlining the progression of changes. Results indicate the usefulness of morphometric analysis of lungs following inhalation of toxic substances in quantitatively defining the structural alterations.

Mar 1, 1989

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period 22 November to 10 December 1982. The testing covered herein is for coarse 2-in by 0 (minus 50 mm) Pittsburgh Seam coal in a 6-in (150 mm) pipeline, at velocities ranging from 5 to 20 ft/s (1.5 to 6.1 m/s) and at concentrations ranging from 15 to 45 pct by weight.

Jan 1, 1986

As the title indicates the central themes discussed in this contribution are sustainable development, information systems, and extractive industry. More specifically, the objective is to present a prototype for the systematic generation of extractive industry (henceforth: EI) û specific sustainability information. The paper begins with the authorÆs viewpoints on the core notions of sustainability, and development, as well as their relationship to information. These set the stage for the introduction of the information system (IS), as well as the follow-up sustainability information system (SIS) extractive industry sustainability information system (EISIS) concepts and related discussions. The paper continues with a second part, in which, efforts to research and develop an EISIS prototype are described. First, the team is presented. Second, the systemÆs aim and target groups are briefly discussed. After, an articulated overarching EISIS conceptual model emphasising capital accumulation, and service flow concepts û is presented. This is followed by a detailed description of the assembled prototype with a focus on data and information generation. The formulation of data generation, storage and transmission processes, as well as its use in sustainability interpretation rules and their embedment in the conceptual model is made with respect to monetised stock and flow parameters, measured in the appropriate dimensions. In the third part, the author presents and discusses the results of a first round of prototype experimental development in three major EI firms. First, the system observation, and data analysis protocols are described. Second, a review of protocol implementation, and respective results, is made. Finally, the overall performance of the proposed prototype, and development process issues are discussed, before suggesting areas for improvement and future research. The paper ends with a conclusion in which the author provides a retrospective balance of the æknowledge creation projectÆ, as well as a prospective outlook for research in this field; before acknowledgements are made and references provided.

Jan 1, 2009

By Tadeu Messias Donizete Borba

A soldagem com elevado aporte térmico é uma das alternativas adotadas pelos estaleiros para aumento da produtividade nas operações de união de materiais. No entanto, os ciclos térmicos gerados durante a soldagem podem provocar transformações microestruturais prejudiciais à tenacidade na zona afetada pelo calor (ZAC). Este estudo teve como principal propósito realizar a caracterização microestrutural e avaliar as propriedades mecânicas da ZAC do aço naval Sincron EH36 produzido na Usiminas por laminação controlada seguida de resfriamento acelerado em comparação com um aço de mesma classe de limite de escoamento produzido convencionalmente, ambos soldados pelo processo ao arco submerso em dois níveis de aporte térmico: 76 e 130 kJ/cm. Foi observado que a presença de uma microestrutura mais refinada nas diferentes regiões da ZAC, associadas ao menor tamanho de grão do metal base e ao menor carbono equivalente, foram os principais fatores que contribuíram para a excelente tenacidade da ZAC do aço Sincron em comparação ao aço convencional. Os resultados obtidos mostraram que é possível obter juntas soldadas com excelentes propriedades mecânicas ao se empregar aço Sincron para a soldagem com altos aportes de calor, e sua utilização pode ser uma estratégia para otimização dos tempos e custos de fabricação na indústria naval.

Aug 8, 2018