Search Documents

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By A. J. Kraemer

This report is one of a series dealing with oil-shale-operations in foreign countries visited and studied by Bureau of Mines oil-shale technologists within the past 4 years. Many oil-shale deposits have been discovered in Brazil and studied with various degrees of thoroughness. In this report the major emphasis is upon the oil-shale concessions of Companhia Nacional de Oleos Mineraes, in the River Valley of the State of Sao Paulo, because this oil-shale deposit is one of the most promising in Brazil for large-scale utilization for the manufacture of liquid fuels and other products of oil-shale processing, and because the opportunity was afforded to examine the concession area and to study mining, retorting, and. refining operations on these shales. Results of detailed analyses at the Oil Shale Research and Development Laboratories of the United States Bureau of Mines, Laramie, Wyo., are reported, Analyses and other date dealing with other oil-shale deposits in Brazil have been compiled from many sources. As many data have been reported as could be correlated to indicate the range of variation of the several types of shale end similar material. The oil-shale deposits in Brazil differ widely in size, richness of the shale, and of the oil. Some deposits are situate& more favorably for exploitation than others.

Jan 1, 1950

By Dziurzyn&apos, W. ski

This article outlines the results of a computer simulation reproducing the transport of a mixture of air and methane following the outburst on 25 November, 2005 in transport gallery D-6, bed 409/4, at the ?Zofiówka? hard coal mine. Based on a mathematical model, numerical method and boundary conditions from the disturbance caused by the outburst, the Ventgraph system of computer simulation programs was adopted for the study. We performed a computer simulation of the influence exerted by the outburst on the propagation of the air and methane mixture, and compared the results of this simulation with those of the actual event as registered by sensors of the mine monitoring system. A validation of the model allowed us to present temporal changes in the concentration of methane and air along flow routes. Keywords: mine ventilation, outburst of methane, numerical simulation, monitoring system.

Jan 1, 2008

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

By Martin D. Conyac

Results of the minerals survey indicate low potential for the discovery of placer gold along Deck Creek aid for copper, silver, and gold in PreTertiary rocks within the boundaries of the Lake Fork RARE II area. Potential for oil, natural gas, coal, and geothermal resources is negligible. No evidence of economic mineral resources was found during the examination of the study area, and no assays of rock or placer samples taken from the urea showed economic mineral values. There are no producing or developing mines within the boundaries o of the lake Fork study area. SETTING Mining Districts The Lake Fork RARE II area is on the eastern fringe of the Cornucopia Mining District, which is centered about 6 mi west. It is also on the western edge of the Homestead district, centered about mi east.

Jan 1, 1983

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

By Loren R. Anderson

This is an Appendix of Volume I. In contains the results of the electric cone penetrometer soundings from the second phase of the testing program.

Jan 1, 1982

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By Lawrence F. Johnsen

In 1989, the Connecticut Department of Transportation authorized the evaluation and design for a reconstructed Route 1 bridge over the Quinnipiac River in the City of New Haven, Connecticut. The project extends from the intersection of Route 1 with East Street, easterly for approximately 3/4 mile to the intersection of Route 1 with Wheeler Street and Stiles Street. The reconstructed roadway will be relatively on-line and widened to provide for four lanes of vehicular traffic and a single-track railway line. The existing bascule bridge and approach spans, which were constructed in 1924, will be replaced by a 270-foot span lift bridge and new approach spans. The lift bridge will have a main lift span weighing approximately 3000 tons, second largest after the Burlington Northern Bridge over the Williamette River in Portland, Oregon. The new bridge will widen the navigation channel to 24 0 feet and provide vertical clearances of 13 feet when closed and 62 feet when open. The project is located in an industrial area. Adjacent properties include retail gasoline sales, auto repair, railroad transport and bulk storage of petroleum. Existing structures include the Yale Boathouse and several retaining walls serving as containment dikes for petroleum storage tanks. The Yale Boathouse, located on the east bank of the river, was constructed in 1909-1910 and is eligible for listing in the National Register of Historic Places.

Jan 1, 1993

By P R. L Browne

Study of geothermal systems in the Taupo Volcanic Zone (TVZ) has significantly advanced our understanding of the processes of epithermal mineralisation. The three main lessons learnt are: 1. knowledge of their chemical anatomy; 2. precious metal transport and deposition; and 3. hydrothermal alteration zoning. These are described in the context of ore formation and exploration.

Jan 1, 1997

By Dale S. Preece, Lee M. Taylor

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry.

Jan 1, 1990

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

By R. A. Ozerkevich, R. J. Voisey

"SherrGold's MacLellan V ne is located about five miles south east of Lynn Lake immediately to the east of the Keewatin River. (Figure # 1)The property is accessible by an all weather road, leading north from the provincial highway 391, which links Lynn Lake with the Town of. Leaf Rapids and the city of Thompson to the south.The MacLellan Mine (formerly the Agassiz property) was discovered in the early 1950's and optioned from Comiesa Corporation in 1979 by Sherritt. SherrGold Inc. was formed in September 1985. Sherritt then transferred the MacLellan Mine, 15 other gold prospects in the Lynn Lake area and the old Lynn Lake nickel-copper mill to SherrGold. At the same time Sherrgold entered into a management agreement with Sherritt whereby Sherritt would develop and operate the MacLellan Mine and conduct SherrGold's exploration activities.The ore body as outlined in the original feasibility study is expected to produce in excess of 300,000 ounces of gold and 450,000 ounces of silver over the next 5 years. However the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 30 miles west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan mine or relocated to Sherritt's Ruttan Operation."

Jan 1, 1987