Search Documents

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By Graham W. Marks, Betsy M. Jones

"Recently4/ it was shown that the total energy method5/ of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing this work, the present report deals with analyses for beryllium, zinc, cadmium, and indium.There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved.As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is associated with zinc and cadmium in zinc ores.The authors wish to acknowledge the valuable assistance of the staff of the Bureau of Mines Analytical Laboratory who made the chemical analyses and supplied the ore samples used in this work.A brief description of the procedures followed in making the standard curves and analyses is given below; a detailed discussion will be found in an earlier paper.6/Basically, the procedure for determining a standard curve consists of two parts: (1) Choosing a suitable line in the spectrum of the element to be determined and (2) determining the variation in the intensity of this line with the amount of the element burned in the arc."

Nov 1, 1948

By M. C. Azar, W. B. Mason, G. L. Anderson

Eminent domain overview Eminent domain is the power of the Government or a municipality to take property for public use without the consent or acceptance of the owner. Typically, the agency taking the prop¬erty will make an offer, hoping the owner will immediately accept and allow work to begin. If a mutual resolution regard¬ing its value cannot be reached, how¬ever, the municipality will institute a condemnation action in court seeking possion of the property. This is when the problems begin. The power of the Government to take the subject property is limited by Federal and state constitu¬tional requirements to pay "just com¬pensation" for the property. The exact nature of an owner's prop¬erty has been the subject of much debate and discussion. It is generally under¬stood, though, that property is consid¬ered to be "every kind of right or inter¬est, capable of being enjoyed and recog¬nized as such, upon which it is practi¬cable to place a money value" (US vs. 53 114 Acres of Land). A taking, for condemnation purposes, is considered to occur whenever there is a substantial interference with the free use and enjoyment of the property. Rarely is the necessity for the taking ever challenged and more rarely is the taking ever successfully challenged. When a taking occurs, it is not only the fee owner who is entitled to compen¬sation. Every person holding an interest in the subject property will be recog¬nized. Thus, all persons who at the time of taking have a compensable interest in the property will be made parties to the case (Swanson vs. US). Minerals, like all other interests in land, are recognized as property rights, giving the owner the power to dispose of them as he or she sees fit. Thus, the only remaining considera¬tion is only "just compensation." Ex¬actly what "just compensation" is has been difficult to define. Generally, it is that amount of money that will "put the person in as good a position as the per¬son would have been in had the taking not occurred." The owner must not be forced to sacrifice or suffer by receiving less than full and fair value for the prop¬erty. Every element that effects the value of the land and that would influence a purchaser must be evaluated. Courts have employed a variety of techniques to determine just compensa¬tion but have generally relied on market value as the standard for measuring compensation to the owner. The deter¬mination of market value is based on sales, income, costs, and use. These factors have been employed in various ways but can be summed up as: -The highest estimated monetary price the property will bring if exposed for sale in the open market with a reason¬able amount of time allowed to find a purchaser who is buying with knowl¬edge of all the uses and purposes to which it is adapted and for which it is capable of being used. • The amount the property would bring if it were offered for sale by one who desired, but was not obliged, to sell, and was bought by one who was willing, but not obliged to buy. • What the property would bring in the hands of a prudent seller, at liberty to fix the time and conditions of sale. • What the property would sell for in negotiations resulting in sale between an owner willing, but not obliged to sell, and a buyer willing, but not obliged to buy. • What the property would be rea¬sonably worth on the market for a cash price, allowing a reasonable time to affect a sale. (Michigan Standard Jury Instructions). Special consideration regarding mar¬ket value is given when the taking is only partial, rather than complete. An example of this partial taking is when a state highway cuts across the northern half of a parcel of property, leaving the rest behind for the owner. A variety of problems can be immediately seen. In a partial taking, the owner is permitted to recover not only for the property taken, but also for any loss in the value of the remaining property. The measure of compensation for partial taking purposes is generally the difference between the market value of the entire parcel before the taking, and the market value of what is left of the parcel after the taking (Michigan Stan¬dard Jury Instructions). Determining the partial taking value for mineral bear¬ing lands is the difficult issue.

Jan 1, 1989

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

By John F. Gamble

Amphiboles are hydrated mineral silicates five of which occur in asbestiform habits as asbestos grunerite (amosite) asbestos, riebeckite (crocidolite) asbestos, anthophyllite asbestos, tremolite asbestos and actinolite asbestos] and non-asbestiform habits (grunerite, riebeckite, anthophyllite, tremolite and actinolite). The asbestiform varieties are characterized by long, thin fibers while non-asbestiform varieties such as cleavage fragments form short fibers with larger widths. The U.S. regulatory method for counting asbestos fibers (aspect ratio [>]3:1, length [>]5 µm) does not distinguish between asbestos and cleavage fragments. The method biases toward increased counts of non-asbestiform cleavage fragments compared to long, thin asbestos fibers. One consequence of this regulatory approach is that workers can be erroneously classified as exposed to concentrations of asbestos (asbestiform amphiboles) above the U.S. 0.1 f/mL exposure standard when in fact they are not exposed to asbestos at all but non-asbestiform amphibole cleavage fragments. Another consequence is that the known carcinogenic effects of asbestos may be falsely attributed to non-asbestiform amphibole cleavage fragments of the same mineral. The purpose of this review is to assess whether amphibole cleavage fragments pose the same risk of lung cancer and mesothelioma characteristic of amphibole asbestos fibers. We identified three groups of workers exposed to non-asbestiform amphiboles: two groups exposed to grunerite (Homestake gold miners and taconite miners) and one group exposed to industrial talc containing non-asbestiform tremolite and anthophyllite in St. Lawrence County, NY. In addition to assessing strength of association and exposure?response trends in the non-asbestiform amphibole cohorts, comparisons were also made with cohorts exposed to the asbestiform counterpart (positive control) and cohorts exposed to the mineral (e.g. talc) that does not contain amphiboles (negative controls). The cohorts exposed to non-asbestiform amphiboles had no excesses of lung cancer or mesothelioma. Similar results were observed in the negative control groups, in stark contrast to the excess risks of asbestos-related disease found in the asbestos cohorts. The only possible exception is the twofold increased risk of lung cancer where exposure was to industrial talc containing cleavage fragments of tremolite and anthophyllite. However, this risk is not considered attributable to the talc or amphibole cleavage fragments for several reasons. A similar increased risk of lung cancer was found in Vermont talc workers, studied in the same time period. Their exposure was to relatively pure talc. There was no relationship between lung cancer mortality and exposure measured as mg/m3 years and years worked. A case?control study reported that all the lung cancer cases were smokers (or former smokers) and attributed the excess to smoking. There were two mesothelioma cases among the NY State talc workers exposed to cleavage fragments of tremolite and anthophyllite, but talc is not a plausible cause because of too short latency and potential for previous asbestos exposure. The positive controls of tremolite asbestos and anthophyllite asbestos exposed workers showed excess risks of both lung cancer and mesothelioma and positive exposure? response trends. St. Lawrence, NY talc does not produce mesotheliomas in animals while amphibole asbestos does. In sum, the weight of evidence fully supports a conclusion that non-asbestiform amphiboles do not increase the risk of lung cancer or mesothelioma. ©2008 Published by Elsevier Inc. Keywords: Amphiboles; Cleavage fragments; Lung cancer; Mesothelioma; Asbestos; Non-asbestiform amphiboles; Grunerite; Talc

Jan 1, 2007

By B Mohanty, M P. Roy, P K. Singh

"The measured response of residential structures is a critical indicator of troublesomeor potentially damaging ground vibrations. A study was conducted to evaluate theresponse of structures situated in the periphery of four open-pit coal mines in India. Although, most of the structures were at far-off distances from the present blasting sites, an attempt was made to document the response of structures to blast vibration for future applications to optimize the blast designs for the safety of the structures. The study involved a total 215 blasts, employing one-, two- and three-hole calibration study, and production blasts. The bench height varied from 7.5 m to 42 m, and boreholes loaded with emulsion and slurry explosives were 250, 260, 270 and 310 mm in diameter. The explosive detonated in a blast were between 300-198400 kg whereas in a delay it was 33-24800 kg. Up to 12 tri-axial vibration sensors were located in overburden along a linear array from 25 m to 6.5 km distance from the blasts. Altogether, 1512 blast vibration signatures were recorded. Production and specially fi red single-charge blasts allowed the determination of natural ground frequency. The fundamental frequency of the structures ranged between 3.13 to 10.6 Hz, the same as those of the ground vibrations. The amplifi cation of vibration in the structures was in the range of 1.6 to 5.6. The study details the interaction between ground vibrations and selected structures, and the means to reduce amplifi cation of vibrations in the structures and persistence of vibrations through improved blast design."

Jan 1, 2008

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

The safety of personnel is the most important matter during a mine fire. However, there is not enough research on a case when a fire occurs near a shaft and the behavior of the fire gas is not well understood. Therefore, a series of experimental study using a scaled ventilation circuit model was carried out. The behavior of ventilation air during a mine fire near a shaft was investigated. The model consists of two vertical shafts, three horizontal ducts connecting the shafts and an exhaust fan from the shaft bottom. The cross section of the shaft and duct is a square of 200×200mm. The height of the shafts is 3400mm. The length of the ducts is 1540mm. The lower duct is set at the same level as the shaft bottom. The middle and upper duct are set at 750mm and 1760mm above the shaft bottom respectively. The airflow rates through the ducts can be adjusted by regulators installed in each duct. The behavior of the fire gas was measured by anemometer, thermometer, and visualized using laser light .The air was ventilated downward in both shafts before the initiation of the fire. Some amount of fire gas of high temperature rose upward gradually along the shaft wall regardless of the downward ventilation after the initiation of the fire. Then the direction of main ventilation air suddenly reversed upward in the shaft. The direction of ventilation reversed in many places in the model and the fire gas reached even the part not anticipated.

Jan 1, 2009

By R. M. Santmyers

The chief compounds of boron are borax and boric acid, both of which have important applications in industry. At present the United States furnishes more than half of the world's requirements of borate materials, practically all from California. Nearly the entire production of borax in this country is under the control of four companies: The American Potash and Chemical Corporation, the Pacific Coast Borax Co., the West End Chemical Co., and the Western Borax Co.

Jan 1, 1931

By J. T. Furey

"A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from a gold/tellurides bearing sulphide ore, and to compare the performance of column flotation to conventional ""mechanically agitated"" flotation.Tests were conducted in a 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail.The ore had an average ""as tested"" feed grade of about 5 g/t gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbragite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of 97%, but produced grades of+ 150 g/t Au. INTRODUCTIONColumn flotation is the most significant innovation that has occurred in the mineral processing industry in recent years and has become an important alternative to mechanical flotation. Column flotation has been most widely accepted and applied in cleaning service where it has frequently proven to be superior to mechanically agitated flotation. Roughing in columns has not been ignored, but early testing indicated that columns may not be capable of achieving adequate recovery and, to date, columns have not been seen as serious competitors for mechanical roughers."

Jan 1, 1990

By Manuel Candia

El presente trabajo describe el sistema de relleno hidroneumático realizado en el centro minero de Carahuara. La aplicación de este sistema consiste en enviar material chancado y mezclarlo con cemento y agua. Posteriormente esta carga se vierte en una tubería de alta presión, que se conecta a una bomba neumática y así enviar la carga a los tajeos que se desea rellenar. De otro lado, la ejecución de este sistema data desde 1975 a la actualidad, teniendo como antecedente la experiencia desarrollada en la mina Yauricocha de Centro Min- Perú y posibilitando su extensión a otras minas, cuyas condiciones se asemejan a la de Carahuara.

Oct 14, 1980

By Kenneth Eilerts, Vincent Smith

"INTRODUCTION Knowledge of the Phase relations of fluids produced from combination wells 4/ at the pressures and temperatures characteristic of production from natural reservoirs is essential to efficient recovery and refining practice. An accurate sample of the fluid from such wells may be prepared by mixing (in the proportions of the measured gas:liquid ratio) gas and liquid taken from the separator conditions of steady flow; and physical properties of the sample, at significant pressures and temperatures, may be determined with suitable laboratory apparatus for use in the solution of engineering problems. The results of study of sample so obtained and of mixtures of gas and liquid from the separator combined in other proportions are presented in this report. Attention was given in the study to the relationship between the physical properties of what may be regarded as the constituent materials - the gas and liquid taken from the separator - and the properties of mixtures of these constituents. Data obtained for the complete range of mixture Proportions are expected to provide a reference scale for the study of other combination-well fluids produced at different liquid:gas ratios."

Apr 1, 1942

By Petrus Christiaan Pistorius, Makunga Daudet Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selective was observed in the rougher concentrate of the galena circuit despite the use of excessive amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords- Sulphide ores, Flotation, Flotation depressant, Mineralogy.

Jan 1, 2005

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

A way back in 1851-2 an army of diggers had commenced the conquest, of the now famous goldfields of Australasia. At that time, and in the Colony of Victoria, more that 10,000 were camped on and around the slopes of the silurian ridges over which Ballarat East h'as been built. A wonderfully rich golden harvest was soon gathered from the alluvial found high on these slopes, and from runs (or gutters) which got their rise on them, and were traced down gullies into a broad valley. In due course it was ascertained that the valley carried a main gutter which represented the unity of the higher ones, and further explorations proved this gutter to have a westerly and then a southerly trend toward and under a basaltic plateau, on the top ofwhich Ballarat West and Sebastopol now stand. In the records of alluvial gold mining all the world over the Ballarat field can be classed amongst the richest. Gold in pieces the size of beans, in, stringy filigree bits, in dust and in solid lumps (the largest of which weighed more than 2,200 ozs.), was obtained in the comparatively shallow ground on the slopes; and speaking generally, great and uniform richness was met with along a belt of country on which, in a north and south line, the present quartz mines of Ballarat East are at work. It was noticed by the diggers that when the gutters crossed the upturned edges of the ,strata, the gold deposits in them were patchy, and that when they trended north and south on this beltthey carried rich deposits for longer distances. In time it was also noticf!d that a class of stringy, irregular shaped quartz occurrences, in a bottom of soft slates, in the, immediate vicinity of tpe g)ltter, meant greater richness, and (in the aIluvial) on the higher ground slabs of quartz would now and then be met with, in which strings and spongy masses of gold were found. As the shallow alluvial became worked out the diggers turned their attention to the quartz occurrences, and, now and again the striking of a flat make of a very golden nature would cause quite a stir in the local mining world.

By James A. Browning

Conventional flame channelling operates continuously at over 120 db --flame-drill channelling at a maximum of 95 db. The latter process was developed under this program. Individual drill holes are spaced to leave narrow rock webs. Sound and dust passing from the hole are effectively treated by a muffler and water injection.

Jan 1, 1980

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By Steven C. Goddard

Since the passage of the Federal Coal Mine Health and Safety Act of 1969, the need for improved duet control methods has become imperative. It has been proposed that one promising dust control technique would be the application of water through the cutter drum. In November of 1972, the Jeffrey Mining Machinery Co., who had been pursuing the development of wet drum miners since 1969, completed the manufacture of a 120M HELIMINER which had sprays in front of the cutting bits on a fixed width drum. On June 27, 1973 Jeffrey and the Bureau of Mines signed the contract numbered B0232060 for the purpose of evaluating "the effectiveness of respirable dust control on a Jeffrey 120M HELIMINER by use of water piped through the head." This evaluation, as described by the contract, was to be accomplished by the collection and analysis of dust samples at various locations of an operating mine production section.

Jan 1, 1974

A computerised cataloguing system for geological specimens is described. The catalogue is designed for use with a compactus-type storage system. The information stored in the catalogue for each specimen includes the type of specimen, locality information in terms of standard ~ap sheets and descriptive location, geological age, stratIgraphy, and specimen descriptions. The catalogue can be interrogated at any level of detail on the basis of any combination of these specimen parameters.Other information stored for each specimen 'is the compactus address, collection date, reference information and the type of analyses performed on that specimen:Any mterrogatlon produces a listing of those specimens which satisfy the search criteria.

Jan 1, 1974