Search Documents

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff of the Explosives Division of the Bureau of Mines and, are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes, of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more' rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about I millisecond after the shpt is fired is illustrated in figure

Jan 1, 1939

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

Jan 1, 1962

By S. Kittel, P. Galleguillos, H. E. Urtubia

The rougher flotation at Escondida consists of 80 cells of 100 m3 each, with injected air. Escondida has developed a system of automatic control of the rougher flotation using video cameras, which have been operating since 1997 for remote monitoring and manual control. Since 1999, an image processing software and a group of rules have allowed implementation of an expert system. To date, the expert system controls the superficial speed of each cell by adjusting the air flow and the froth depth of the flotation bank. Preliminary tests of the expert control on two of the eight rows gave 1.2% higher rougher recovery at a 92% degree of confidence. The proven benefits are already sufficient to move towards a complete plant implementation.

Jan 1, 2001

By Takashi Sasaoka

Indonesia is the second largest coal exporter to Japan, accounting for about 30 M tons annually. They produced about 150 M tons in 2005, over 99% of which being from open-cut mines [1]. However, the conditions of surface mining are becoming worse each year: the stripping ratio is increasing, approaching the economic ratio and the infrastructure for coal transportation from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. At present, there are only five small underground mines, three of which are old and the other two have only recently begun mining operations [2]. However, severe ground control problems have been occurring regularly, roof falls in particular. At a new mine developed from the highwall, a large bolted roof fall occurred at the heading face, killing two miners. Unfortunately, mining engineers and/or miners in this mine do not have a lot of experiences, expertise and know-how concerning the operations of underground coal mines. Since 2001, Japan has started a ?five-year plan for coal technology transfer? to fill Japan?s moral obligation as the largest coal importer in the world. The research team for this accident was organized and the on-site investigation was conducted in order to find the cause of this accident and make the solution. This paper describes the roof fall accident at the mine, discusses its causes and mechanism and suggests the introduction of some techniques for improving the current support system considering the strata and stress conditions by means of field observation and finite element modeling.

Jan 1, 2007

A subsurface study of the Maria Lode and associated hydrothermal alteration of andesites within the Karangahake epithermal gold-silver deposit defined the local evolutionary sequence in the once active geothermal system.   Some implications for mining of epithermal deposits arise as a result.

Jan 1, 1984

By E. Chin

The countries of Asia and the Pacific have large resources of diverse minerals. Australia and China have extensive mineralization that are commercially being exploited. The major minerals in Australia with known reserves adequate for both domestic demand and export markets include bauxite, clays, copper, diamond, gold, iron ore, lead, manganese, mineral sands (titanium minerals), nickel, salt, silver, tin, uranium, and zinc. China is the world leader in proven reserves of antimony, barite, magnesite, molybdenum, rare earths, titanium (ilmenite), tungsten, and vanadium. It also has about 55 billion tons of iron ore, albeit with an average grade of only 30 % to 35 % elemental iron content. With the exception of chromium and copper, China has significant resources of a wide array of minerals and metals, based on its production and/or export capability for these commodities. Additionally, India has significant resources of bauxite and mineral sands; Indonesia, bauxite, copper, nickel, and tin; Malaysia, tin and associated titanium; Mongolia, copper, fluorspar, and lead-zinc; New Caledonia, nickel; New Zealand, gold and iron sand; North Korea, magnesite; Papua New Guinea, copper, gold and mineral sands; Philippines, copper, chromite, and gold; and Sri Lanka, gemstones. Moreover, there appears to be extensive mineralization III Burma (Myanmar), Cambodia, Laos, Thailand, and Vietnam, but they have yet to be definitively delineated.

Jan 1, 1994

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

This study was conducted to determine the feasibility of using large tractor dozers in land reclamation of strip-mined areas. The procedures used are patterned after engineering models developed for evaluation of military ground vehicles in cross-country operations. Tractor dozer manufacturers furnished information on capabilities of existing equipment and ideas on the practicability of using dozers larger than those currently available Generally, they believe that current dozers in the 500? to 700-horsepower range are about as large as can be built and remain economically feasible. However, one manufacturer has a wheeled dozer rated at 1200 horsepower, and another is testing a tracked dozer of about the same horse-power.

Jan 1, 1975

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By Mark S. Sanders

This report presents a summary of the work reported by Sanders and Kelley (1981). A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were indentified. The visual attention locations are contained in this report. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars & scoops were used to test the procedure. Illustrative results are presented in the report.

Jan 1, 1981

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By Michael B. Cortie

Mesoporous gold sponge has the unique property of being both metallic and highly resistant to oxidation. It has potential application in catalysis, in bio-sensors, in optical coatings, in analytical chemistry and, as we show here, as the basis for a new kind of ultra-capacitor. Due to the cost of gold, the most probable niche for a gold-based ultra-capacitor would be in the high-power/high-energy regime, a region where gold would compete with devices based on RuO2. A high internal resistance limits the power that can be usefully drawn from existing carbon-based ultra-capacitors, and that this problem can potentially be overcome by gold-based devices. A simple proof-of-concept ultra-capacitor based on mesoporous gold is described and its behaviour during charge and discharge cycles examined. In this work a step change in the input or output voltage of the device was used as the controlling parameter. There was also a residual faradaic current resulting from traces of undissolved aluminium left over from the AuAl2 precursor used to make the sponge, and some charge storage due to polarization of the solution. Deconvolution of these three effects was not entirely accomplished, but an ostensible capacitance of about 7 to 14 mF/g Au was demonstrated. Further improvement from these early results seems likely.

Oct 1, 2003

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By William H. Holley

Thirteen additional preservative/fire retardant systems were applied to Ponderosa pine and evaluated for flammability both before and after water leaching. The more promising four systems were given a thorough evaluation for flame spread, toxic gas and smoke density levels, resistance to decay, and compressive strength. The most promising system on the basis of history of usage in the mine, ease of application and low cost as well as overall performance is the Fyreprufe/ACC Albi 107A/ 144 combination. A survey of inspection tools and instruments, identified equipment which could be assembled into an inspection kit for use in determining the extent of decay and/ or impregnant retention levels in mine timber. A literature search identified those high fire hazard areas found in a typical mine. Timber and other wooden structures used in such areas should be treated with an acceptable fire retardant system. A survey of insurance companies revealed that the use of such treated timber in the mines would probably have little or no impact on the rate structure.

Jan 1, 1980

By Steven M. Rupprecht

"The artisanal mining sector in Central Africa is largely informal, yet provides an essential livelihood for many (directly or indirectly) participants, as well as facilitating an important source for the flow of income into many communities. Artisanal mining varies from site to site, but appear largely well structured despite its informality. The artisanal mining sites in Central Africa have some inherent management structure and the extraction itself is often organised. Artisanal mining is labour intensive and is generally conducted utilising hand digging methods e.g. shovels or hand chisels. Artisanal mining is generally more dangerous than small-scale or large-scale modern mining operations. This is especially true as artisanal operations are generally subsistence activities with artisanal miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. The objective, through proper/dedicated training of artisanal miners is to migrate Artisanal mining to establish a small-scale mining (SSM) industry in Central Africa. Through developing the necessary skills in the fundamental areas of mining it is proposed that Artisanal Mining can become more productive and safer mining operations. The paper reviews the above focus areas, highlighting the skills and tools that are necessary to assist in establishing a sustainable small scale mining industry migrating from manual labour to semi-mechanised mining and processing. The purpose of the transformation process is to create a safe, healthy, environmental and community oriented mining operation with the objective to uplift the skills and wealth of the mineworkers and the general community."

Jan 1, 2015