Search Documents

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By H. Shang

The materials science and metallurgical engineering communities have expended enonnous resources in developing high fidelity process models. Exploiting these Models for Predictive Optimization (MPO) and Control (MPC) is a new frontier in Materials Process Engineering that will lead to exceptional process perfonnance. This paper will begin with a short survey of the development of high quality process models available in the literature and a discussion of how these could be used to improve process operation. A summary of the current "state-of-the-art" in process automation technologies and the traditional framework in which these technologies are deployed will be presented. An illustration of the use of MPO in process design and operations will be presented for the continuous casting of steel. In addition, a simple run-out table simulation will be used to demonstrate the power of the MPC technique.

Jan 1, 2003

By Leonardo Mota, Lucas L. da Costa, Milton B. Filho, Sergio N. Monteiro, Helion Vargas, Tammy G. R. Portela da Silva

"A natural biofoam extracted from the buriti palm tree has shown characteristics for potential substitution of synthetic foams. In the present work, a photoacoustic thermal characterization was performed on buriti biofoam samples. An open photoacoustic cell technique and a photothermal rise method performed under continuous laser illumination were employed in order to determine the thermal diffusivity and the specific heat capacity of such material. In addition to their intrinsic values (finger print), these physical parameters represent the light-into-heat conversion efficiency and the amount of heat stored per unit volume, respectively. The results showed that the buriti biofoam presents thermal properties that permit its use as an effective insulation material.IntroductionSolid foams are very light materials with increasing engineering applications [1]. A natural biofoam obtained from the petiole of the buriti palm tree (Mauritia flexuosa) has been recently investigated [2-4]. The evaluation of the buriti biofoam properties and the characterization of its microstructural aspects have shown that this biofoam has a potential as a new engineering material with very low density. Additionally, its reduced open porosity and low absorbed humidity revealed a promising material for packing and floating applications. In fact, this buriti biofoam, extracted from the palm tree natural of the north region of Brazil, is being used by the low income population as a modest substitute for Styrofoam® [1].As a potential insulating material, the buriti foam needs to be characterized in terms of its thermal and acoustic properties. A preliminary investigation [3] on the thermal behavior of this natural biofoam by thermogravimetric analysis, TGA, and its derivative, DTG, as well as differential scanning calorimetry, DSC, revealed parametric conditions associated with water loss and structural decomposition. Both the surface humidity and the release of hydration water were determined. Different decomposition events were attributed to both, more rigid as well as to more flexible molecular segments. Table 1 depicts technical data obtained so far for the buriti biofoam. These data are compared to those corresponding to Styrofoam®."

Jan 1, 2011

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011

By Mariana Barcelos, Frederico Muylaert Margem, Giulio Rodrigues Altoé, Pedro Amoy Netto, André Gomes, Sergio Neves Monteiro

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of polyester matrix composites reinforced with continuous fique fibers, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Jan 1, 2015

By Katsumi Ogi, Hiroto Uchida, Masamitsu Sato, Atsushi Itsuki

"(BTMSE)Ag(hfac) (BTMSE = trans-bis(trimethylsilyl)ethene) was chosen as a suitable precursor for the XeCl laser (308nm) MOCVD of Ag. Iso-propanol solution of (BTMSE)Ag(hfac) was used as a liquid source for the liquid delivery method, high deposition rate 9nm/min at substrate temperatures of 100°C and 120°C were obtained at the vaporizer temperature of 90°C. This deposition rate is three times faster than by conventional bubbling method and life of the source and reproducibility of the deposition were also improved. Electric resistivities of the laser deposited film shows significantly low resistivity of 10-6Q-cm compared to 1 o-3Q-cm of thermal MOCVD film. These results indicates that the laser MOCVD is one of the effective method for the preparation of the high quality silver film.IntroductionSilver films are a potentially important metallization material in electronic and photonic devises due to their lowest resistivity (1.6µ0-cm) among the metals, high optical reflectance and chemical stability. The MOCVD technique has advantages to sputtering or evaporation in the point of conformal growth and better coverage on sharp steps and narrow gaps[l-2]. For MOCVD application, silver precursors must have sufficient vapor pressure without decomposition at their evaporation temperature. To achieve stable precursor gas supply, liquid delivery of precursor material is promising[3-4] especially for materials that have not enough heat stability and high vapor pressure like silver complexes[S-10]. Several new silver complexes for MOCVD and UV irradiation effect to their MOCVD silver film quality were reported by same authors[5]. In this paper new solvent system for liquid delivery system of silver MOCVD were investigated to suite XeCl(308nm) laser MOCVD application."

Jan 1, 1998

By Terry Gerritsen

Electrode control systems regulate power by physically positioning electrodes. Due to the size and weight of the electrodes, this is a slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +I- 20% around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicans's laterite nickel furnace, yielding excellent results with a 3 to I reduction in power fluctuations. Keywords: SPLC, AC Power Supply, Electric Furnace

Jan 1, 2004

By Xiyun Yang, Hui Xu, Xichang Shi, Xiang Xiao

"Rod-like magnetite particles were prepared by precipitation of iron salts with urea under the induction of magnetic field. Temperature and initial Fe3+/Fe2+ ratio have a significant effect on the composition of the product. Magnetite particles change from spherical into rod shape in the presence of a 0.35 T magnetic field, The addition of a small amount of spherical seeds increases the rod-like magnetite particles yield. The seeds are prepared by aging ferrous and ferric solution with sodium hydroxide as precipitator. The aspect ratio of the rod is controlled by varying the volume ratio of seed to iron salt.IntroductionMagnetite, an important member of magnetic materials, has attracted a lot of attentions for its super magnetic properties. The rod-like magnetite particles have high anisotropy and coercive force as well as super magnetic properties compared to other shapes, and are widely used as high magnetic density media, magnetic devices and microwave materials [1-4]. Recent studies have found that magnetic field can direct magnetite growing along easy magnetization axis to get one-dimension particles [5-6]. Chen et al. [7] synthesized single crystalline nanorod magnetite under magnetic field. Wang et al. [8] discovered that magnetite grew along easy-magnetization directions under 0.35T magnetic field. Vereda et al. [9-1 O] found that magnetic field had a dramatic effect on the morphology, inducing the aggregates to line along one direction to form rodlike particles.At present, most of the synthesis methods reported in the literature result in a low yield of rod particles and the aspect ratio are difficult to control. Recently, we developed a seed-mediated growth approach to making rod-like particles in an aqueous solution. The spherical magnetite generated by oxidation serves as a seed. These seeds are then added to a solution containing iron salt and urea, and provide nucleation sites for magnetite rod growth."

Jan 1, 2011

By Takahiko Okura

Most non-ferrous raw materials are associated with sulphur. To extract the metals, the sulphur is recovered typically as Sulphuric acid or liquid S02. On the other hand, natural gas may contain over 20% of hydrogen sulphide (H2S) and a huge quantity of elemental sulphur is produced through oil and gas refining processes in the world. A large fraction of the sulphur mined from natural sources is eventually returned to the earth as fertilizers, by-products of desulphurisation and neutralisation processes, or as fugitives to the atmosphere. However, the supply and demand for sulphur are in imbalance. Such situation urges to develop a new smelting process without sulphuric acid production. This paper briefly reviews the global sulphur balance and the technologies for recovering elemental sulphur. The core of this paper is a proposal to convert S02 gas to elemental sulphur by using organic materials. Some results of thermodynamic calculations and experiments are presented.

Jan 1, 2003

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By D. Morin

A general study of gold refractory arsenopyrite-pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 I unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery. Furthermore. the arsenite and ferrous produced in solution have to be oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimization study calculation for scaling-up the design and power requirements of an industrial installation. For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution. In that conditions the power cost is quite marginal. actually it is significant for the treatment of pure pyrite.

Jan 1, 1991

By T. T. Chen

Kidd Creek continuously-cast copper anodes are characterized by high levels of Se, Pb and Ag; the anode slimes constituents and their morphologies are controlled by both the anode composition and the casting process. Hollow Cu2Se spheroids and tube-like structures, enveloping Cu-Pb-As oxide and/or Cu2O, are present in the as-cast copper. During electrolysis, the selenides are liberated from the copper and accumulate in the slimes layer; the Cu2O and Cu-Pb-As oxide react rapidly with the electrolyte to form soluble species and PbSO4. Silver, which is present mostly as a solid solution in the anode copper, is also liberated during electrolysis and reacts with the Cu2Se to form (Cu,Ag)2Se. The ultimate composition of the selenides in the slimes layer depends mostly on the Ag and Se contents, but various other elements, including Au and Te, are also structurally incorporated. Although the selenides are the major Ag carrier, metallic silver also is present. A thin layer of Cu2O crystals sometimes forms at the copper surface, and may affect anode passivation. Copper sulphate is a common constituent and serves to agglomerate the slimes. Copper sulphate is present on both passivated and non-passivated anodes, but that observed on the passivated metal is present as a thick compact layer. Copper powder is associated with CuSO4.5H2O only on passivated surfaces.

Jan 1, 1987

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By Luiz A. Teixeira

A process is described whereby worn, deffective or crystallized photoconductive Se-As layers can be stripped off from aluminium photocopier drums, using hydrogen peroxide solutions in conditions such that the aluminium substrate is preserved from chemical attack. The process allows the stripped drum to be recoated with a new photoconductive layer, and to be put again in use.

Jan 1, 1990

By H. Y. Sohn

"The nonferrous production industry has gone through a remarkable transformation in recent years in terms of developing and adopting new technologies. Technology innovations have largely been driven by the need for greatly improved environmental protection in addition to increased productivity. One of the most notable aspects of the new technologies is their ability to reduce the emission of sulfur and other pollutants to extremely low levels.The current industry trends towards more environmentally friendly technologies are bringing about additional benefits of developing more efficient, technically advanced, and continuous processes in closed reactor vessels. Key aspects of these modem trends include the use of increased oxygen enrichment in the process gas, better process control, reduced manpower requirements, and plant operations with more skilled personnel.Computer simulation and modeling of complex processes have become more reliable, realistic, and thus increasingly useful in metal production. Some of the notable examples are reviewed.Finally, the need and advantages for value-added production in the nonferrous industry are discussed.I. IntroductionMost recently commissioned technologies for nonferrous metals production have been developed largely in response to environmental concerns. One of the most remarkable improvements made by the nonferrous industry in the last decade has been the rapid increase in sulfur capture. Before the start of the last decade, 90% capture of sulfur was considered good. Since then, strict emission regulations have become the norm in advanced societies, although smelters in many parts of the world still operate with limited pollution control. Other emissions and discharges have also been substantially reduced, resulting in much improved working conditions and worker hygiene in addition to the overall environmental protection. The development of the more environmentally friendly technologies has accompanied other advantageous advances made in the nonferrous industry, i.e., the trend towards more gas-tight, continuous processes and larger plants. This has increased the competitive edge enjoyed by the industry in the industrial countries, offsetting the higher costs of labor and pollution abatement that they have to overcome in those countries. Experience has shown that clean technology often leads to a profitable business, because its adoption forces the concomitant advancement of related technologies in addition to the avoidance of penalties imposed by the public on pollution-prone industries. Needless to say, there are other driving forces for new technologies such as reduction of operating and capital costs, improved product quality, and energy considerations in terms of reduced consumption and utilization of readily available sources."

Jan 1, 2000