Search Documents

Bath smelting options for recovering valuable metals from jarositic residues containing 22-28% lead and 16-30% sulphur obtained from pressure leaching zinc-lead-copper bulk concentrates were investigated using thermochemical computations and crucible-scale experiments. Direct fuming of lead and zinc from a slaglmatte bath at 1250-300°C was demonstrated successfully. Up to 93% of the lead was recovered in the fume and steady-state recoveries of zinc were predicted in the range 82-95% under these conditions. The energy required for the fuming reactions was supplied by partial combustion of the fuel, added as char, with air. An important feature of the process is that the recoveries to the fume are not significantly affected by changing: the fuel:air ratio over a wide range. Thermodynamic computations, confirmed by experimental results also showed that the presence of a matte phase is not essential for high recovery of lead and zinc to the fume. Operating conditions which produced a matte ensured that about 70% of the silver and 80-90% of the copper were recovered into that phase. Approximately 98% of the arsenic in the residue was fumed. In the absence of matte the slags contained high arsenic levels (260-330 ppm) but low arsenic (20-60 ppm) levels were achieved when matte was produced.

Jan 1, 1994

By V. A. Luganov

During the treatment of raw materials containing arsenic and antimony, problems in the distribution of these elements in the process products occur. In a number of cases in processing of copper-bearing materials, it is possible (or necessary) to obtain speiss. The purpose of the present research is to study the theoretical aspects and analyze the technological possibilities of producing copper-bearing speiss and the subsequent electrometallurgical processing with copper extraction as well as arsenic and antimony utilization. Copper arsenide (Cu3As) and copper antimonide (Cu3Sb) are the main components of the speiss. A thermodynamic analysis of the electrochemical oxidation of Cu3As and Cu3Sb, carried out using Pourbaix diagrams, showed that in a pH range from 0 to 2, oxidation potential 0.45-0.55V, ions of copper and arsenic and antimony trioxide are in the equilibrium. The kinetic study has shown, that with an increase in the polarization potential, the dissolution process changes from chemical to diffbsion control. An increase in temperature stabilizes the electrolysis process due to dissolution of arsenic trioxide forming on the anode. Electrolysis of speiss using a cathode diaphragm with the solution pH = 1-2, current density 150-200 A/m2 and temperature 60-70°C makes it possible to obtain cathode copper with a current efficiency of 95-96% and to remove the arsenic from the process during the electrolyte cleaning process. The arsenic content in the cathode copper did not surpass 0.002%. As the result of the research, a technological flowsheet for copper-lead speiss processing was developed. At the present time this technology is undergoing pilot testing.

Jan 1, 1999

By Nexhmedin Lohja

Macro management of metallurgical industries becomes an important issue in certain situations especially when some government owned metallurgical industries are on the verge or have stopped being feasible. In these cases a government lead macro management in collaboration with domestic institutions and foreign scientific and management expert companies is decisive in order to steer them to a profitable path. This process is not necessary an easy one and incorporates many unknowns and various alternatives. In this paper the macromanagement of the metallurgical industries in Albania will be described as a particular case along with a survey of its mineral deposits, metallurgical facilities and various perspectives for future development. As a country with many mineral resources, the exploration, research, exploitation and processing work of mineral ores before 1990 constituted an important activity of its economy, especially in the exportation of various products of this industry. Since 1990 this activity slowed downs considerably for various reasons and this prompted the necessity of a government lead macromanagement in collaboration with domestic institution and foreign expert companies. This process aims at improving and renewing the technologies in the metallurgical industry in order to transform it into a feasible branch of economy. This goal is being implemented among others through proper geological surveys, rehabilitating and renewing the existing facilities through domestic and foreign investments, the transformation of the ownership or the management from state-owned to local or foreign private companies, etc. Priority is given to the raising of the processing range of the traditional minerals such as chromium, copper, nickel-iron etc. as well as developing new perspective technologies to treat new mineral deposits.

Jan 1, 2006

By T. Ranki-Kilpinen

In the flash smelting technique, developed by Outokumpu Oyj, off-gases with dust load are directed into the heat recovery boiler (HRB). As the temperature decreases, metallic sulphates become thermodynamically stable. Sulphation of oxidic particles initiates. The release of heat causes an increase in particle temperatures, and soft sulphated particles can stick to the heat transfer surfaces. Dust accretion may form and cause operational problems. The objectives of the project are to study sulphation reaction mechanisms and kinetics of flue- dust particles under HRB conditions, and get more information for the flue-dust treatment possibilities. The sulphation behaviour of synthetic Cu2O particles (37-53 pm) was studied using a fluid-bed reactor of laboratory scale. The experimental parameters in the latest campaign were oxygen and sulphur dioxide contents of 2.5-10 vol-% 02 and 40-60 vol-% SO2 respectively and temperatures of 600-660°C. Samples were examined microscopically (SEM+EDS) and chemical analysis were conducted. The sulphation rate was found to have a maximum at the certain temperature, which was dependent on the gas SO2 content. Regardless of the level of SO2, a rise in oxygen content promoted sulphate formation.

Jan 1, 2002

By S. Vukcocic

A long term research project is in progress to establish the parameters of an acid leach process to recover alumina 'froui' high-iron and/or low-iron white bauxites, kaolinite, coal. ash and copper mine tailing. In this paper the results of acid leaching of copper flotation tailing for the removal of alumina are presented. The tailing is very complex material which contains 25% Al203 in the -10 lim fraction. X-ray diffraction indicates presence of quartz, kaolinite and minor 'alunite. After classification and ,separation of the -10 lim fraction, the raw material is fired to 550GC and leached at 90GC. Filtration is applied for the separation of white silicate residue form leach liquid. After the purification step, aluminum salt is crystallized from the solution, and calcined to alumina. Kinetic correlation and regime, of the processes are defined and presented in the paper.

Jan 1, 1992

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By Abhishek Asthana

The incineration of Municipal Solid Wastes (MSW) is an attractive process for reducing the volume of the wastes and recovering their energetic value, which, however, requires to be strictly controlled in order to limit its impact on the environment. In this context, we have undertaken the mathematical modeling of the different sections of a typical incineration plant. The combustion of the waste bed, usually carried out on a moving grate, is at the core of the process. This paper presents the 2-dimensional, steady-state model that we have developed for simulating the MSW combustion. The model describes gas flow through the porous waste particle bed, the gas-solid reactions, conductive and radiative heat transfers, drying of the feed, its pyrolysis and the emission of volatile species, combustion of the pyrolysis gases, the formation of char and its gasification by water vapor and carbon dioxide, and the consequent reduction of the bed volume. Pyrolysis kinetics distinguish between cellulosic and non-cellulosic materials and are experimentally derived from our laboratory measurements. The calculated results give a deep insight into the various involved phenomena, an example being the complete consumption of oxygen in a large zone of the bed and the related appearance of a char gasification zone. The influence of various operating parameters, like the temperature and flow rate of primary air, is presented and explained. Finally, the effect of stirring the waste bed on the moving grate is also analyzed.

Jan 1, 2006

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By Nexhmedin Lohja

The production of high-carbon ferrochromium in a submerged electric furnace based on double-level technology has some advantages compared to close-type furnaces with one tap hole. These advantages include the reduction of the specific energy consumption for the overall process, good separation of ferrochromium from slag, an effective treatment of raw materials including lean chrome ores (low percentage of Cr2O3) etc. An outline of the operation of this furnace along with the production line of briquettes from fines of chrome ore by using organic and inorganic binders, will be followed by a description of the recent work carried out to improve the energy consumption in this furnace through a pre reduction process of Cr2O3 ores by the off-gas energy recuperated from the furnace and the use of SiC in the feed. A short theoretical analysis of the new work will also be given.

Jan 1, 2006

By John Jiang, Yeonuk Choi, Olivia Wang, Gus Van Weert

"As part of a general review of processing double refractory ores through Barrick Gold's autoclaves/CIL facility at Goldstrike, Nevada, blanking the gold cyanide adsorbing native carbon in the ore with hard (m.p. >55°C) paraffin wax was proposed. To avoid interference from other ore constituents in the exploratory testwork, commercial activated carbon was substituted for native carbon in the ore to establish the best conditions for de-activation of carbon with molten wax.IntroductionDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including the Goldstrike deposit, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (POX). It is the latter route to which this paper refers.The second barrier refers more correctly to gold recovery. Gold may be extracted from the autoclave oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This behaviour is used advantageously on a large scale by gold millers, who use man made activated carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold after autoclave oxidation."

Jan 1, 2012

By Ovidiu Pasca

Several improvements in converter equipment and operation at BHP Copper have reduced the converter cycle time as necessitated by an increase in flash furnace output. The resulting higher intensity performance of the Peirce-Smith Converters has had a major impact on the dust handling and off-gas cleaning systems. This paper describes work carried out on the design of a new converter hood with particular reference to the thermal analysis and hood performance aspects. Changes in converter cycle time and campaign life as result of the process and equipment improvements are discussed in a separate paper.

Jan 1, 1999

By Malcolm J. Harrison

The problems associated with the flow control of abrasive slurries and solids laden fluids creates reliability problems in many mining operations. Conventional valves such as pinch, knife gate and plug types cannot always function reliably in such harsh operating environments. Due to the technological advances in the hard coating industry, ball valves can now be produced with internal surfaces protected from the erosive effects of these applications. Pressures well in excess of the capability of conventional 1000 kPa working pressure valves can now be handled reliably. The significant advantages of minimizing down-time and lowering maintenance costs can now be realized with metal seated ball valves.

Jan 1, 1999

By A. Robles

The main goal of the present work is to propose a viable alternative for selective arsenic elimination from copper smelter flue dust without the need of a global leaching scheme for all the individual components of the flue dust. Using this alternative, the inherent copper recovery problems are avoided. Arsenic precipitation is also considered for regenerating the solution and completing the process cycle. The experimental results for arsenic extraction and precipitation are satisfactory. Concentration of NaOH used was relatively low. The main reason for succeeding in high arsenic extraction and low NaOH consumption is due to the previous water washing of the flue dust. Water washing dissolves much of the iron and copper that are present in certain percentage as sulphate.

Jan 1, 1999

By K. Koike, N. Masuko, Y. Takasaki

At the Zinc & Lead'95 symposium, one of the authors presented several modifications of Pb-Ag-Ca alloy anodes for the zinc electrowinning process, and also, the behavior of some organic additives in the electrolyte. In this study, the mechanical properties of the electrode materials composed by Pb-0.5 wt% Ag-(0~0.8) wt% Ca were studied by the tensile and Vickers hardness methods. Furthermore, experimental research on the influence of rolling and annealing treatments on the electrolytic behavior and mechanical properties of these alloys was carried out. The tensile strengths of the annealed Pb-0.5 wt% Ag-(0.1-0.8) wt% Ca alloys were the same or higher than those of the as-cast Pb-0.9 wt% Ag alloy. The anode potential using the as-cast Pb-0.5 wt% Ag-0.6 wt% Ca alloy decreased compared to the as-cast Pb-0.9 wt% Ag alloy. Moreover, the annealed Pb-0.5 wt% Ag - 0.6 wt% Ca anode after rolling showed a lower anode potential than the as-cast Pb-0.5 wt% Ag - 0.6 wt% Ca anode.

Jan 1, 2000

By Andreas Nolte

In 1999 HÜTTENWERKE KAYSER AG (HK) in Germany will produce more than 180,000 t/y of electrolytic refined copper. To achieve this production from materials with copper grades from two to seventy percent and diverse copper alloys, HK operates three blast furnaces, one holding furnace two Peirce Smith converters and two anode furnaces. Technical, metallurgical and economic factors for the ongoing process optimization are outlined. The fluctuating quality and quantity of raw materials renders complex this optimization. The principal variables are the quality and quantity of process consumables: coke, copper-iron, limestone, oxygen, as well as the blending of feedstock and a new organization of the operating crews. The search for new metallurgical process parameters is ongoing. HK started with an intensive research programm in November 1997. As a result it will be possible to cut processing costs by about ten per cent, to increase the blast furnace capacity by ten per cent and to lower the metallurgical losses of copper and tin in the slag by more than ten percent. The presentation concludes with information on future steps to continue the optimization process.

Jan 1, 1999

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By Laurentiu Nastac

"This paper describes the development and validation of a comprehensive multiscale modeling approach capable of predicting at the mesoscopic scale level the ingot solidification structure and solidification-related defects commonly occurring during the vacuum arc remelting (VAR) process. The approach consists of a coupling between a fully transient macroscopic code and a mesoscopic solidification structure code. The predictions from the multiscale model, including grain morphology and size, primary and secondary dendrite arm spacings, Laves and NbC phases, tendency for freckling and columnar-to-equiaxed transition, were validated against experimental measurements for a 20-inch diameter VAR alloy 718 ingots. The validated model was then used to investigate the effects of melting rate and ingot diameter on the solidification structure of VAR processed 718 ingots.IntroductionThe objective of this work was to develop a fully transient multiscale modeling approach to get an insight into the effect of processing parameters on the cast micro- and macro-structure during VAR processing. The developed model assists in achieving better control of the ingot solidification structure and to determine trends in the macrosegregation in these ingots. Another objective of this work was to analyze the transient effects of production rate and ingot size on the resultant ingot microstructures. This objective was met by first understanding the effects of the full range of processing parameters typically used in the VAR process. Processing parameters such as power input and heat extraction rate significantly influence the ingot liquid pool size and shape as well as the ingot structure, which in turn will greatly impacts the final ingot quality."

Jan 1, 2012

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By L. A. Kazanbayev

The Chelyabinsk Electrolytic Zinc Plant (CEZP) was commissioned in 1935. Over the elapsed years the Plant capacity has been increased from 10 thousand tons of zinc (1935) to 150 thousand tons of zinc (2005). The paper describes the Plant main achievements in production updating for the last 10 years.

Jan 1, 2006

By B. J. Beaudry

Intermetallic compounds are frequently required in the form of thin sheets for magnetic refrigeration and other applications. Progress has been made in the preparation of thin sheets of brittle gadolinium intermetallic compounds by hot rolling of sheathed billets. The effect of fabrication procedures on the Curie temperature of GdPd and its heat capacity at low temperatures has been studied.

Jan 1, 1989