Search Documents

By Laura Garcia H, Juan Carlos Gonzalez Islas, Luis Garcia Lechuga, Pedro Alberto Ramirez Ortega

"Electrochemical studies were performed to silver recovery from industrial wastes (radiographic films) on litanium flat electrode using a filter press-type electrochemical reactor with vertical orientation (known as REOV-01), as counter electrode was used a mesh-type DSA. Voltammetric studies were employed to fmd the current range under which silver reduction occurs. Using chronopotentiometric studies with controlled current, homogeneous deposits were obtained on the surface of the Ti electrode, to a current of -210 mA during 120 minutes to a constant linear flow velocity of 15 Lmin-1 was achieved 97% of silver recovery from industrial wastes. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy studies corroborated the presence of silver on Ti flat electrode. In addition, the silver concentration in the solution after the experiments was 1 ppm below environmental requirements. This indicates the viability of a filter press-type electrochemical reactor with vertical orientation (REOV-01) for silver recovery from radiographic filmsIntroductionIn recent years, the industrial sector has shown an increase in the use of silver due to new applications in different areas. In sectors such as photography, the consumption of silver has declined as a result of the boom in digital photography. However, the use of silver in radiographic applications has not shown greater variation (47.16 Moz), as the image quality is essential for diagnosis in various fields, such as medicine. All the silver used in photographic applications is discarded completely (solid or in effluent). At the present, several countries have been involved in silver recovering from industrial wastes due to the economic value and environmental impact they represent. The main source of silver recovery is the wastes generated by the photographic sector. Various technologies have attempted to recover silver contained in these wastes. However, they have not fully satisfied the requirements of maximum recovery, nor environmental level (less than 5 ppm) of silver in effluents [1,2]."

Jan 1, 2014

By A. D. Zunkel

The zinc in electric arc furnace dust (EAFD) arises from the fuming and oxidation of the zinc present, mainly as galvanizing, in automotive scrap. The dust is collected from the electric furnace offgases in bag filters and is classified by the EPA as a hazardous waste (K061). As more zinc is used in galvanized sheet on automobiles and more automobile scrap is recycled via the EAF, the more zinc will be available for recovery and recycling. EAFD will become a more prevalent and important source of zinc compared to the traditional zinc sulfide concentrates ifit can be cost effectively processed.

Jan 1, 1995

By René Bustamante

A GPSS/H simulation is beeing done for a traditional smelter of copper, which envolves a reberberatory furnace, a set of Peirce Smith converters (PSC) and a refining furnace. The objective is to try different plant layouts, being the handling of liquid material at high temperature one the mainly concern, this envolves a study of the ladles and cranes used. Some of the modifications that can be evaluated through the model is the role of oxygen potential when tonnage oxygen is used, number of cranes, PSCs in operation, etc.

Jan 1, 1992

By T. Maruyama

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating with one Flash Furnace (FSFE) and three Peirce-Smith Converters since its start-up in 1972. Anode production capacity has increased from 101,000 to 263,000 t/y by the several expansion programs, while converter capacity has increased and stable operation has been established by several improvements as listed below. - Expanding the furnace body (length) - Development of two kinds of automatic scrap charging system for each converter. (Increasing the in-stack time and better control of the melt temperature) - Oxygen enrichment at slag blow and copper blow - Increasing the blowing rate This paper reports the details of these improvements.

Jan 1, 1998

By A. D. Zunkel

Increasing amounts of electric arc furnace dust (EAFD) are being generated worldwide as more steel is produced from electric furnace melting of galvanized steel scrap. In most countries, the management of this material is a costly technical, economic, and legal problem for minimill steelmakers. Many technologies and processes are being developed and implemented worldwide to manage this material to recover contained zinc, lead, and iron values and render it nonhazardous. These processes are pyrometallurgical, hydrometallurgical, or hybrid in nature. Some produce zinc oxide, some zinc metal, some lead metal, and some lead cement. Some are successful, some have failed, many are dormant. or abandoned, and others continue to be developed and emerge. This paper updates the current status of 20-30 processes in various stages of commercial application and development used worldwide to manage EAFD and recover its nonferrous, particularly zinc and lead, and ferrous values.

Jan 1, 2000

By M. C. Nielson

The paper describes the design and operation of pulsed columns as replacements for conventional mixer/settlers. The advantages, which the columns offer, include a reduction in real estate for the plant, elimination of diluent evaporation, containment of noxious vapors and reduced crud formation. In addition to the description of operation, the paper presents the findings of laboratory tests of pulsed columns extracting copper from pregnant leach solutions and also delineates potential advantages of the pulsed column in copper solvent extraction.

Jan 1, 1999

By Takao Mori

Novel rare earth boron icosahedral compounds are investigated as potential high temperature thermoelectric materials. REB50-type compounds and REB22C2N compounds were synthesized and the thermoelectric properties measured. Seebeck coefficients in excess of 200 V/K are observed at temperatures above 1000 K for the REB50-type compounds. Strikingly, n-type behavior was observed for REB22C2N. Up to now, non-doped B12 icosahedral compounds have all been p-type. The discovery of an n-type compound is extremely important in terms of the potential development of this class of compounds as viable thermoelectric materials. Low thermal conductivities of < 0.03 W/cm/K at room temperature was observed for these rare earth boron cluster compounds.

Jan 1, 2006

By G. Hanko, A. Lebleu, M. Sibony, J. Lecadet

The New Jersey distillation process is today the most important pyrometallurgical method for the production of zinc of very high purity. The flexibility of the pyrometallurgical zinc production process, especially its ability for recycling, makes it competitive, although it is energy intensive. A deeper knowledge of the New Jersey process is necessary to further increase its technical performance by ensuring its global safety. A project, integrated in the European research program EUREKA, has been started in order to define the process chemistry of distillation. Experimental measurements have been carried out with a column at the laboratory scale, and the results, linked with industrial measurements, support the development of a model based on material and thermal balances. The first conclusions indicate that the key parameters for process optimization are the column geometry and the distribution of the thermal losses.

Jan 1, 2000

By Vinod K. Namilakonda

In situ synthesis of discontinuously reinforced aluminum alloy metal matrix composites was investigated. Aluminum alloy (A356: Al-7 wt% Si) was reinforced with dispersed AlN particles. Thermodynamic calculations were made for the composition determination of various phases formed during bubbling of NH3 gas into the Al alloy melts in the temperature range 1173-1473 K. Experiments were carried out for in situ production of AlN particles with the reaction between Al melt and NH3 gas in high temperature resistance furnace at 1473 K. The products were characterized using SEM, EDS and XRD. Effect of bubbling time of NH3 gas on the AlN formed in the composites was studied. The amount of AlN reinforcement in the Al alloy composites was observed to be in the range of 5 to 35 wt%. Good agreement was observed between the experimental and thermodynamic calculated data on the composition of AlN in Al alloy composites.

Jan 1, 2006

By Melissa L. Trapani

The removal of molten products from metallurgical furnaces is one of the most hazardous and labour intensive processes in a non-ferrous smelter. The proximity of operators to the molten metal and slag during tapping and the oxygen lancing that facilitates the flow have led to many reported injuries on tapping floors. In most cases, tapholes are opened and closed periodically leading to extreme thermal cycling in the tapping assembly. As a consequence, refractory wear rates are high and unpredictable in the taphole. This paper provides a review of the current state of taphole development, and gives a methodology that is now being applied to gain a better understanding of the taphole region to allow design improvements.

Jan 1, 2002

By Sundarrajm Suresh, Hrushikesh G. Pimpalgaonkar, Thiyagarajan Paramadayalan

In this paper, a model of a fuel cell system has been proposed to account for the membrane physics at the micro level which is coupled with the macroscopic flow and mass transport phenomena occurring in a single channel of a Polymer Electrode Membrane Fuel Cell (PEMFC) system. We have developed a novel approach to model the catalyst layer electrochemical processes in a Membrane Electrode Assembly (MEA) and coupled it with mass transport and fluid flow calculations at the channel level using STAR-CD commercial software. The predicted values of the cell voltage from this micro-macro model are validated with experimental data available in the literature. A sensitivity analysis has been carried out to study the effect of the design and operating parameters such as catalyst loading and initial temperature on the overall performance of the PEMFC. The results indicate that the cell voltage increases at higher platinum catalyst loading and is also independent of the choice of initial cell temperature.

Jan 1, 2012

By G. S. Nus

Technology for treating man-made metal-containing raw materials in DC electric furnaces with polarization of the bottom phase (PDF furnaces) has been developed and proven on a semi-commercial scale. PDF furnaces permit processing of man-made raw materials, i.e. current and accumulated intermediate products with rather high contents of valuable metals (i.e. slags, sludge, residues, Waelz slag, etc.), as well as secondary raw materials and virtually any type of waste using an environmentally safe technique based on sublimation of volatile metals and transfer of non-volatile metals and sulfur into the bottom phase in the furnace. Processes developed on the basis of the use of PDF furnaces make it possible to take advantage on a full commercial scale of electrolysis of molten materials, including electrochemical reduction of metals, intensification of their settling into the bottom phase and sublimation of volatile components, as well as to significantly improve recoveries of nonferrous metals, resolve the problem of excessive accretion formation in slagging processes and substantially improve the environmental situation. The low-grade discard slag obtained can be utilized in the construction industry; in particular, slag can be added to the limestone feed for cement manufacture.

Jan 1, 2006

By Jason Graetz

Aluminum hydride is a covalent, binary hydride that has been known for more than 60 years and is an attractive medium for on-board automotive hydrogen storage, since it contains 10.1 % by wt. hydrogen with a density of 1.48 g/ml. There are at least 7 non-solvated AlH3 phases, namely a, a&apos;, a, ?, d, e and ?. The properties of a-AlH3, obtained from the Dow Chemical Co. in 1980, have been previously reported. Here we present a description of the thermodynamic and kinetic properties of freshly prepared a, 0 and y phases of AlH3. In all cases the decomposition kinetics are appreciable below 100" C and all will meet the DOE 2010 gravimetric and volumetric vehicular system targets (6 wt% H2 and 0.045 kg/L). However, further research will be required to develop an efficient and economical process to regenerate AlH3 from the spent A1 powder.

Jan 1, 2006

By Jinxing Ji

The thiosulfate lixiviant system for leaching of gold has been under extensive investigation for nearly two decades and consists of ammonium thiosulfate, copper and ammonia. There are several challenges with this system. The occurrence of ammonia must be taken into account from a health and hygiene aspect in the workplace, and also from an environmental perspective with significant levels of ammonia and copper in the tailings. Copper accelerates the leaching rate but causes excessive thiosulfate degradation. A new lixiviant system that has been investigated consists only of sodium thiosulfate without copper and ammonia. Gold leaching is carried out in an enclosed reactor with slightly elevated oxygen overpressure and temperature. Extensive leaching experiments were carried out to minimize thiosulfate degradation and polythionate formation while maximizing the gold extraction. For the preg-robbing carbonaceous ore sample tested, gold leaching was essentially complete within six hours and the thiosulfate consumption was lower than in the typical ammoniacal thiosulfate system. The gold thiosulfate complex in the pregnant leach solution was found to be quite stable under ambient conditions. This new leaching system has the advantages of being more environmentally friendly, has a shorter residence time, lower thiosulfate consumption, lower oxygen consumption, and is easier to control.

Jan 1, 2003

By P. Barrios

Over a period of one year, an in-depth investigation was carried out in a conventional copper refinery to understand the behaviour of silver in copper electrolysis. The increase in silver content in the cathodes increases almost linearly with the duration of electrolysis, and the silver content of the electrolyte between the electrodes shows similar behaviour. The silver content of the cathode deposited daily depends directly on the silver concentration of the electrolyte and this, in turn, is strongly influenced by its internal temperature. The average temperature between the electrodes rises from the first to the second and to the third crop, because of the increase in the distance between the electrodes and the heat generated by the passage of the current. The mechanism of dissolution of silver from the anode, and its passage to the cathode, are discussed. Following the change to the Isa system, it was proved that the results and conclusions are analogous. Based on these results, a reduction of more than 20% in silver losses in the cathodes was achieved.

Jan 1, 1999

By R. D. Prengaman

Wrought lead-calcium-tin anodes developed by RSR Corporation have improved the performance compared with the other lead alloy anodes. These anodes have been in continuous service at various locations around the world for as long as fourteen years. Calcium provides mechanical strength to the anode to prevent the deformation while tin increases the mechanical strength, reduces the rate of corrosion, prevents the formation of non-conducting layers on the anode surface, and dramatically improves the conductivity of the anode. Tin is also instrumental in developing the unique rolled structure of the anode which leads to the reduced rates of corrosion, longer life, and improved oxygen evolution. Cobalt additions to the electrolyte further enhance the oxygen evolution and improve the anode life. Higher current densities and higher operating temperatures reduce the anode life. The unique patented method of attaching the rolled anode sheet to the bus bar substantially reduces the resistance of this important joint and offers the substantial savings in power over the life of anode.

Jan 1, 1999

By L. B. Tsymbulov

At present data on thermodynamic properties of metallic melts, containing copper and ?iron family? metals, is rather limited. Determination of the activity of metallic melts components under high temperature by experimental methods requires high level of labour inputs. With this it is not always possible to obtain the results with high level of accuracy. Due to that in a number of cases it is more appropriate to apply different methods of analysis, with the help of which there can be calculated thermodynamic properties of ternary and even more complicated systems, prominent thermodynamic properties of binary systems being used as a basis for these calculations. This work presents the results of calculations of different components activity and activity ratio in such ternary system melts as Ni-Cu-Fe, Ni-Cu-Co, Fe-Cu-Co and Fe-Co-Ni. Good compliance of calculations results with those obtained in the course of reliable experimental investigations fulfilment is demonstrated. There are presented the results of activity and activity ration analysis for some compositions of Cu-Ni-Co-Fe system.

Jan 1, 2006

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By M. M. Salari Rad

An investigation of gold distribution in the mill products of Sar Cheshmeh beneficiation plant demonstrates that on average 44% of the gold is routinely recovered as a by-product in the copper concentrate, and the remaining is lost to the tailing. In order to evaluate the causes of gold losses, the distribution and mode of gold occurrence in the Sar Cheshmeh ore and mill products were studied. Searching for gold within samples and within individual grains of sulphide minerals was carried out by SEM in the backscattered electron mode and SIMS, respectively. The mineralogical distribution of gold revealed by microbeam techniques were combined with the results of relevant metallurgical experiments including, sizing, heavy liquid separation, and diagnostic leaching tests, and the nature and location of gold in the ore and mill products were determined. The combined results of the experimental approaches pursued suggest that while there are some gold in solid solution and/or -colloidal size within sulphides of the Sar Cheshmeh ores, "visible" gold is the principal form of gold occurrence at Sar Cheshmeh.

Jan 1, 1999

By P. K. Jha, M. M. Mahapatra, H. K. Mohanty, Pradeep Kumar

"During friction stir welding, the tool geometries affect the weld together with the process parameters like welding speed, vertical pressure and tool rotational speed. The present investigation deals with the three dimensional computational fluid dynamics modeling of friction stir welding process considering material flow around the tool, welding speed with respect to tool geometries. Friction stir welding tools with different tool geometries were used for the experiments to achieve acceptable aluminum welds. The temperatures near the welds for each tool were experimentally observed. A 3-D computational fluid dynamics (CFD) model was developed. Temperature-dependent material properties of the aluminum alloy were used in the CFD model. Thermal analysis was carried out considering rotational speed, vertical pressure and traverse speed for the tool geometries. The numerically predicted stirring patterns and temperature profiles closely matched with the experimental ones. IntroductionThe friction stir welding (FSW) is a solid state welding process where generally the metallic materials are joined by the combined action of frictional heating and weld zone stirring by a rotating tool [1]. The heat generated in the process is much below the requirement of melting the plates; hence the FSW process is devoid of harmful effects those are observed during arc welding. The FSW process utilizes a tool which has a shoulder and a protruding pin known as the probe. The shoulder is responsible for frictional heating while the pin probe facilitates stirring of the joint material. A schematic of FSW process is shown in Fig. 1."

Jan 1, 2012