Search Documents

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By D. M. Hausen

A computer program has been developed by Newmont Exploration to convert mineralogic data by XRD into rock type and ore type classifications. This method has proven useful in identifying lithology from cuttings samples, where percussion drilling was an alternative to expensive core drilling. Computer printouts of rock type and ore type identifications can be generated simultaneously with mineralogic analyses, resulting in a considerable time savings in manual calculation. XRD-computer logging was first applied to the Carlin mine in north central Nevada, and later to the Maggie Creek and Gold Quarry gold deposits, southeast of the Carlin mine. Impure Paleozoic limestones of the "lower plate" Roberts Mountain Formation and the "upper plate" transitional facies have been decarbonatized to altered siltstones and shaley units along vertical faults and permeable stratiform horizons. Advanced stages of decarbonatization were accompanied by silicification. Quantitative XRD data are initially sorted into principal rock type units (limestones, siltstones, dolostones, shales) based on major mineralogic components (calcite, quartz, dolomite, clays). On the basis of relative amounts of less major constituents, descriptive subclassifications (dolomitic limestones, dolomitic siltstones, argillaceous cherts) are made. XRD lithologic data provide assistance in correlating lithologic units, and delineating favorable replacement horizons associated with gold mineralization.

Jan 1, 1982

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By Kim Fagerlund

Boliden Harjavalta Oy operates a copper smelter in Finland, which is based on flash smelting together with Peirce-Smith converting of copper matte. This paper reviews a case study when a high arsenic feed mixture was successfully eliminated in order to guarantee the anode quality. Based on theoretical and practical knowledge in slag chemistry at Outokumpu Research, the CaO-fluxing practice was introduced. Description of a thermodynamic simulation using MTDATA and implementation of the results into converting practice is given. Results showed that the impurity fluctuations in raw materials could be effectively controlled by efficient utilization of different slag chemistry.

Jan 1, 2005

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By Teixeira

An experimental investigation on the kinetics of oxidation of As(III) with H202 in synthetic effluent solutions followed by precipitation of Fe/As (V) compounds was carried out. The variables investigated were: As concentration (200 -3000 mg/l) , oxidation pH (2.0 -11.0), oxidation temperature (25 -800C) , H202 stoichiometric excess (50% -100%), precipitation pH (5.0 -7.0), precipitation agent (Fe2+ -Fe3+). Fixed conditions were, Fe/As molar ratio (6:1) and stirring speed (560 rpm). The results were empirically modelled. The precipitates obtained were amorphous. The precipitates were checked upon their environmental stability according to the United States Environmental Protection Agency (U.S.E.P.A.) Toxicity Test, and were considered to be adequate for deposition in impermeable waste dumps. The combined Fe/H202 detoxification process, in selected conditions, was able to reduce the As contents of effluents containing 1600 mg/l As to 0.1 mg/l, in about 2 1/2 hours of total processing time.

Jan 1, 1990

By Jaroslav Horskoý, Miroslav Raudenský, Bogdan Filipic, Božidar Sader

This paper describes main elements and practical use of the computational system for automated setting of optimized casting conditions in the continuous casting of steel. The system consists of the heat transfer model of the process, empirical metallurgical criteria, and optimization algorithm. The physical model of the, strand temperature distribution relies on the classical Bennon-Incropera mixture continuum formulation for the convective-diffusive heat transport. Fluid flow effects are considered through enhanced thermal conductivity of the liquid phase. The model is solved by the operator-splitting Crank-Nicolson finite volume version of the Voller-Swaminathan scheme. The solution procedure is coupled with the IDS solidification analysis package. Boundary conditions for the strand cooling rely on combination of the generic and plant-specific mold, spray, and roll heat transfer coefficients ' by coping the effects of the casting speed, casting temperature, casting powder, mold oscillation mode, steel grade, water or air-mist spray type, running water, trapped water on the rolls, and radiation. The caster safety and productivity and the quality of the strand are related to nine empirical metallurgical criteria. The criteria ensure the caster safety and economy as well limit the internal, longitudinal, and transversal surface cracking possibility. The problem of finding optimum casting parameter values is stated as a minimization problem based on the analytical form of the cooling criteria evaluated from the steady-state temperature distribution of the strand. To solve the optimization problem, a genetic algorithm is employed. The algorithm explores process parameters settings heuristically by applying the principles of biological evolution. It starts with a random set of solutions and iteratively improves them through selection and variation. Solutions are evaluated by running the heat transfer model of the process and extracting the values of the empirical metallurgical criteria.

Jan 1, 2000

By Kenneth McGowan

"The aluminum industry is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating accounts for 25% of the energy consumed to manufacture aluminum. Consequently, the generation of this energy results in the production of a significant amount of CO2 (over 3.75 million metric tons in 2003)1. As a result, the Aluminum Industry Technology Roadmap of 2003 listed the development of improved refractory materials as a goal to reduce energy use and decrease greenhouse gas creation. The result of a R&D effort addressing this desire is the development of patented microporous refractory materials for metal contact applications in all furnace areas including the belly band. It has been demonstrated that this material can reduce energy consumption up to 38% in furnaces and significantly reduce heat loss in launder and trough systems. Furthermore the material developed is non-wetting and remains un-penetrated by metal throughout its lifetime. The material does not contribute to the formation of corundum. As a result, the energy efficiency of an older lining remains intact compared to standard refractory materials which may have an initial high insulating value (such as lightweights and board) or standard dense refractory (even with penetration inhibitors) both of which show a rapid increase in thermal conductivity as the refractory is penetrated with aluminum and formed corundumIntroductionThe aluminum industry is the second largest producer of metal in the United States, behind the iron and steel industry. It is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating is required to melt, hold, purify, alloy, and heat treat the metal and accounts for 25% of the energy consumed to manufacture aluminum. As such, process heating is the second largest energy consuming operation. Smelting, which utilizes an electrolytic reduction process is the largest energy consuming operation1.Most process heating is accomplished through the use of fossil fuels, either directly or indirectly. The choice of fuel is dependent on a plant’s location and fossil fuel availability. Table I shows the processes impacted by refractories and the calculated BTU’s generated by usage of the respective fuels as well as the Metric Tons (MT) of metal passed through each process in 20001."

Jan 1, 2009

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

By Wellington Pereira Inácio, Fernando Wypych, Sergio Neves Monteiro, Artur Camposo Pereira, Rafael Marangoni

"The efficiency by which an applied load is transmitted from the matrix to reinforcing fibers in a composite depends on the fiber/matrix adhesion strength. This is determined as the interfacial shear strength, IFSS, which may be measured by means of pullout tests that measure the force needed to pull a single fiber out of a block of material simulating the composite matrix. Different techniques are used to perform pullout tests. The objective of this work was to characterize the IFSS of sisal fibers embedded in epoxy matrix through the determination of the critical length pullout curves. As the main results, a relatively small critical length was found for the sisal fiber/epoxy pullout specimens, corresponding to a weaker IFSS. This was compared to other results applying different pullout techniques. Scanning electron microscopy observation identified the mechanism responsible for the weak sisal fiber adhesion to the epoxy matrix.IntroductionSynthetic fiber reinforced composites is today one of the most successful class of materials with increasing industrial applications from house appliances to large airplanes like the modem Airbus 380. However, environmental issues are revealing serious drawbacks related to the fabrication, use and post-use discard of these composites. For instance, the thermoset polymer composite reinforced with E-glass fiber, known as ""fiberglass"" has an energy-intensive fabrication associated with a surplus emission of C02, which is responsible for global warming [1]. Moreover, the glass fiber is considered toxic and also causes long term pollution after being discarded."

Jan 1, 2011

By B. Garcia-Egocheaga, J. Rutten, N. Goicoechea, U. Meurer, Mager K., W. Saage, Simonettim F.

Because of the increasing use of zinc as an active and passive anticorrosion agent for steel, leading to constantly growing return rates of galvanized steel components, especially through the automotive industry, major Electric Arc Furnace (EAF) flue dust amounts with higher zinc contents will accumulate in future. Landfilling of steel plant flue dusts is no longer allowable for ecological reasons. These dusts are classified as hazardous by law. Waelz technology is safe and reliable. The range .of treatable feed materials has been extended by process modifications and state-of-the-art offgas technology. Waelz oxide, the product, is delivered to metal smelters for zinc production and the byproduct, Waelz slag, can be used in road construction. Despite the fact that Waelz technology is among the best available techniques (BAT), it is continuously being optimized further with respect to energy input, product and offgas quality in order to comply with the ever more stringent environmental regulations. However, if these flue-dusts are treated, the loops between the steel and the zinc industry can be closed by reusing recovered zinc which in tum leads to savings in natural resources and a more reasonable use of landfills.

Jan 1, 2000

By Huimin Lu, Qiang Li, Jingbo Xu

"The smelting reduction of V-Ti bearing beach placer by combined rotary hearth furnace and direct current arc furnace was studied in laboratory. It takes the aid of back propagation (BP) neural network theory to build the nonlinear mapping relations between the crucial process variables such as content of carbon, temperature and time and the degree of reduction. Then by the integrating BP neural network and genetic algorithm (GA), the optimized process parameters for the high degree of reduction were searched. The comparisons between experiment results and neural network simulation results show that GA-based on BP method can predict the degree of reduction with higher prediction accuracy. Calculations show that the integrated energy consumption of new technology is 580kgce/tHM, less than the current existing blast furnace.IntroductionThese V-Ti bearing beach placers (VTBBP) are secondary Fe-rich minerals formed by rivers, ocean waves, ocean tides and ocean currents on beach zones, their useful minerals are V-Ti magnetite ores. On Asia Pacific zone, such as Japan, China, Philippines, Indonesia, Australia and New Zealand, the VTBBP have large reserves and wide distribution. But so far, the VTBBP are not still comprehensively utilized. Therefore, in this paper, a combined rotary hearth furnace technology and arc furnace smelting method is studied for comprehensive utilization of the VTBBP. The main objective of this paper is to find optimum operation conditions for the production ofV-bearing iron and titania-rich slag from the VTBBP by means of the laboratory testing.Recently, neural network (NN) expected to be able to provide an effective tool because of its advantages, which describe nonlinear mapping relations. With the characteristics of strong selflearning, self-organization, robust error toleration and accurate nonlinear relation approximation, artificial neural network can be applied to nonlinear process modeling based on sufficient training. Back-propagation (BP) training algorithm is probably the frequently used one in practical application. Genetic algorithm has parallel search strategy and global optimization characteristics, which makes the trained neural network being higher classification accuracy and faster convergence speed. So it is necessary to combine neural network and genetic algorithm. The nonlinear relationship between input and output presented by NN and the global optimal function of GA are abroad applied in the engineering and scientific research [1, 2]. So these methods supply an efficient path to solve the above problems. At present, it is common to study the optimization of process parameters by orthogonal experimental design, the method combining neural network and genetic algorithm is a novel and better method than orthogonal experimental design. Tills study organized the above advantages to optimize the process parameters for comprehensive utilization of the VTBBP."

Jan 1, 2012

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

By N. L. Piret

Reprocessing of low zinc-bearing residuals with a zinc content of less than 10%, originating from the iron and steel industry, has been given more and more attention in the last few years, due to the potential landfill liability and the increasing cost of disposal by dumping. Whereas, recycling of hazardous electric arc furnace dust is already being performed commercially on a large scale in the U.S., Japan and Western Europe, almost no reprocessing takes place in the case of these low grade zinc-bearing materials. In blast furnaces and basic oxygen furnaces dusts and / or sludges are generated at a rate of 1 to 2 % of the respective production. The technologies for the retreatment of these types of materials, either commercially available or still being developed are briefly described hereafter. They involve internal recycling, upgrading by physical separation methods, separate hydrometallurgical processing and pyrometallurgical treatment. Their scope and limitations are critically assessed in terms of technological applicability, economic feasibility and environmental compatibility. Since, the possibtlity of achieving economic profitability is unlikely with this type of material, the main criteria for acceptability of the treatment process are: generation of a iron-rich material, suitable for treatment by the iron/steel industry, acceptance of the non--ferrous metal-bearing sub-product by zinc smelters, generation of non-hazardous waste materials.

Jan 1, 1992

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004

By Ling-yun Yi, Yuan-bo Zhang, Bing Hu, Zhu-Cheng Huang, Zhen-yuan Liao

"Nucleation and growth mechanism of iron crystal grain in coal-based shaft furnace direct reduction process by microwave heating were investigated by optical microscope, scanning electron microscope and EDX. The results indicate that microwave has selectivity on various minerals which absorb microwaves. The high temperature in certain area of pellets and thermal stress on the interface of minerals are formed, results in the wustite grain smashed along the joints, and iron crystal grains turned out a spherical shape obviously. The iron crystal nucleus is formed firstly at the edge of wustite, on the interface between grains and in the holes in pellets, and grows gradually while reduction carries on from surface layer to inner core. Microwave heating promotes the rate of transportation and accumulation of the iron crystal grain, increases growth rate of iron crystal grain and contributes to formation of dense iron-jointed crystal texture eventually.IntroductionMicrowave energy as a new energy, which selectively heating materials through internal energy dissipation, has the advantages of heating uniformity, high thermal efficiency, fast heating, clean and pollution-free compared to conventional heating motheds. Microwave energy also has obvious superiority in increasing productivity. Thus, it has been widely used in many areas, including electronics, food processing, chemical, medicine, environmental protection, and family life etc [1]. As a rapidly developed green metallurgical method, microwave heating also has been widely recognized by areas of grinding, pretreatment, pre-reduction, drying, furnacing, metal extraction, and waste materials processing and utilization. Some research achievements are gradually putting into practice, showing great potential in chemical and metallurgical industry [2-3]."

Jan 1, 2011

By E. Ozberk

The copper and nickel smelting industries are important contributors to the technical and economic well-being of Canada while some of the smelters are among the largest sources of sulphur dioxide emissions in Canada. A review of the operations in six smelters - Falconbridge Limited, Falconbridge, Ontario; Hudson Bay Mining and Smelting Co. Limited, Flin Flon, Manitoba; Inco Limited, Copper Cliff, Ontario and Thompson, Manitoba; Noranda Mines Limited, Horne Division, Noranda, Quebec and Gaspe Mines Division, Murdochville, Quebec - have shown that about 80% of the total sulphur input to these smelters was emitted to the atmosphere in 1980. A simultaneous review of the existing and emerging technologies which can directly or indirectly reduce the sulphur dioxide emissions indicated that it is possible to reduce the emissions to below 20% of the sulphur input to these smelters. This can be achieved by varying degrees of modifications to the smelting operations and installing sulphur fixation facilities at significant costs which may increase the metal production costs. This would consequently make the competitiveness of the Canadian copper and nickel producers more difficult in the already tough world metals market.

Jan 1, 1983