Search Documents

By Lamar S. Todd

The direct production of metal from a sphalerite concentrate is an attractive route for primary zinc. A series of operations and conditions have been selected to efficiently cause the following overall exothermic reaction. The process uses a continuous circulation of molten copper for material and energy transfer between the unit operations. Sulfide concentrate is reduced with an excess of superheated copper to make a copper alloy and white metal. The alloy is stripped of volatile metals under vacuum and some metals can be separately condensed. The residual copper and the white metal are fed into a copper converter to be blown with oxygen for desulfurizing and the superheated copper is recycled. The paper will include a detailed material flow sheet for the process, discussion of the operating conditions of the individual units, behavior of minor elements, and zinc quality.

Jan 1, 1999

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002

By K. Osseo-Asare

Third phase formation, the separation of a solvent extraction organic phase into two liquids, is generally attributed to the limited solubility of the extracted complexes in the hydrocarbon diluents. Much of the research on third phase fomiation, therefore, emphasizes experiments designed to establish the stoichiometry of the species responsible for the limited solubility. This work offers a different approach, based on the recognition that the solvent extraction third phase, in fact, corresponds to the middle phase in a microemulsion fluid system. Using the tri-n-butylphosphate (TBP)-diluent-water-electrolyte system as a model system, current concepts of microemulsion phase behavior are utilized to develop a general framework for interpreting and predicting the patterns of phase behavior in solvent extraction systems.

Jan 1, 1999

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By Jan A. Aune

The paper describes a number of electric furnace equipment modules especially developed or modified for slag furnace applications. Both the resulting design concept for a modern electric sulfide smelter and some of the changes in traditional process-concepts made possible are outlined.

Jan 1, 1983

By Shengli Wu, Mingyin Kou, Laixin Wang, Xinliang Liu, Zhennan Qi, Yujue Wang

Softening and melting experiments were conducted on four kinds of imported lump ores named A-D, under different temperature intervals within the self-developed visualization high temperature furnace. By calculating the reduction and shrinking degree under different intervals, softening and melting indexes were determined. These ores all expanded firstly followed by shrinkage with the temperature increasing. The difference of lump ore’s own characteristic led to different softening and melting behavior. The results showed that the looser the structure was, the better the reducibility will be. The compact structure and good reducibility led to high expansion rate. The beginning softening temperature declined and the ending softening temperature increased because of high porosity, which resulted in wide softening temperature interval. The charging ratio of lump ore A should be improved. Lump ore B should be distributed in the center of the blast furnace. Lump ores C and D should be used less.

Jan 1, 2016

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Versiane Albis Leão

This work aims at the selection of an appropriate eluant for cyanide recycling using ion exchange resins. Based on a literature review as well as on experimental results, the elution of resins loaded with copper and minor amounts of iron and nickel is discussed. The resins Imac HP 555s, Amberlite IRA 900 (Rohm&Hass) and Purolite A860S (Purolite Co) were eluted using either NaCI, zinc and nickel cyanides, hydrochloric acid, sulfuric acid or acid thiourea solutions. The results indicate that saline solutions are effective only with polyacrylic resins (Purolite A860S), failing to desorb the metals, specially the nickel cyanocomplex, loaded on polystyrene-based resins. Cyanide solutions of both zinc and nickel are capable of eluting over 90% of the loaded metals. In contact with pure acid' solutions, iron precipitates onto the resin beads, as Cu(II) ferrous cyanideCu2Fe(CN)6.xH20. Thiourea is able to elute all the three metal cyanocomplexes owing to the increased solubility of copper cyanocomplexes in the presence of this complexing agent. The results demonstrate that a universal eluant is not available and the selection of the most appropriate resin-elution procedure should be based on the specific features of the system under consideration

Jan 1, 1998

By Shinroku Matsuzaki

Data the measurement sensor installed with spatial distribution on the blast furnace were successively accumulated online from the process computer to the database system over a long period. This is a new system that accurately considers the relation with the installation position of each sensor, and picture computerization of the measurement data was developed. The overall operation state of a blast furnace, which skilled operators can see in their mind?s eye, was objectively visualized as pictorial information.

Jan 1, 2006

By Ann E. Visser

Aqueous Biphasic Systems (ABS) form upon the admixture of certain water-soluble polymers or polymers and salts above critical concentrations, and thus represent liquid/liquid extraction systems whose nature is entirely aqueous. We are currently investigating the utility of ABS (and its solid phase analogs) as "green" alternatives to the use of volatile organic diluents in separations of metal ions. Chaotropic (water-destructuring) metal ions with small negative AGhyd (e.g., Tc04) tend to partition quantitatively to the PEG-rich phase of an ABS, but even hydrated metal cations can be partitioned to the PEG-rich phase if a suitable extractant (e.g., halide, dye, crown ether, etc.) is used to produce a more chaotropic ion-complex.

Jan 1, 1999

By Keuncheol Choi, Yonghack Lee

"The new lead smelter based on the QSL technology was started operation from May 1992 at Onsan Refinery of Korea Zinc Co., Ltd. The smelter is designed to treat not only various types of lead concentrate but also secondary materials coming from the zinc plant without special pretreatment.Shortly after the start-up of the operation, it has demonstrated that the smelter have a capability to treat wide range of raw materials. Continuous modifications and improvements of the plant are still under way to increase the feed rate and also the ratio of secondary materials to the feed.In this paper, the operating experience and results of QSL smelter, especially the injection of gases and coal to the melt, will be presented with major operation parameters and data.INTRODUCTIONThe QSL lead smelter based on new injection technology was commissioned at the Korea Zinc's Onsan plant from May of 1992. After starting the operation, the QSL lead smelter faced various kinds of mechanical and metallurgical troubles. However, these were gradually worked out by the continuous improvements and efforts.At present, the QSL lead smelter is operated stably at the total feed rate of 57 tonnes per hour with an increased amount of secondary materials."

Jan 1, 1996

By Robert E. Moore

Synthetic spinel is proving to be a highly effective refractory for specific applications, but its cost limits applications. Formation of spinel from a raw material such as diaspore or bauxite could provide a suitable and less costly starting material. In the study reported here, finely ground (-325 mesh) diaspore from Missouri and bauxite from Guyana and China are combined with hardburned MgO (-325 mesh) in appropriate proportions to yield spinel and spinel with secondary phases. A classical sintering and creep study was completed, accompanied by a microstructure study to determine completeness of the reactions and morphologies of the reaction products.

Jan 1, 1991

By Mariana H. Staia

Thermodynamic calculations based on the free energy minimization method were performed for the system Ti-Fe-Mn-0-C1-C in order to evaluate the chemistry associated with the chlorination of an ilmenitic concentrate using CCl4. In the calculations various weight ratios of FeTi03/ CC14, a , were considered, which varied between 0.32 to 0.98 at temperatures ranging from 673 K to 1273 K , at atmospheric pressure. The results obtained indicated that the operating conditions for a process in a packed bed reactor, which implies the chlorination of both Fe and Ti, are 0.39 < a < .49 at T 1173 K.

Jan 1, 1993

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By T. S. Montgomery

The performance of carbon-magnesia brick in electric arc furnaces (EAF) is interpreted in light of their observed optical microstructures. Features at the bricks&apos; hot faces were protruding periclase grains, metal globules, graphite-metal contacts and linear void patterns. These features were com-pared to similar features previously seen from microstructures of basic oxygen furnace (BOF) refractories. Modes of formation were sought; an attempt was made to interpret their influence related to wear mechanisms.

Jan 1, 1982