Search Documents

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By John Petersen

Heap bioleaching technology has become well established for the exploitation of copper sulfide ores. Still, in many operations the rate of copper extraction is rather slow, often taking two years or more to recover 80% of the copper. Chalcocite, the most common secondary copper sulfide, leaches by a two-stage mechanism. The first stage is rapid, whereas the second stage has a high activation energy and proceeds slowly at ambient temperatures. Nonetheless, this rate is still considerably faster than what is typically realized in a full-scale heap. A comprehensive column bioleaching study of a chalcocite ore has shown that the chalcocite columns are leached in a zone-wise fashion. The first zone corresponds to the first stage of chalcocite leaching, where all ferric produced by the bacteria is immediately consumed and all acid entering with the feed solution is consumed within a relatively narrow band. The second stage of chalcocite leaching proceeds much more slowly in the wake of the first stage, within a zone that grows gradually over the entire length of the column. The overall rate of leaching is thus determined by the rate of acid supply into the column rather than by mineral or bacterial kinetics, at least until the entire column is engaged in second-stage chalcocite leaching. In full scale heaps, there is evidence to suggest that solution distribution favours channelling between relatively large clusters of material which are exposed only to stagnant solution. Reagents have to migrate into such clusters by diffusion, which retards the delivery of acid dramatically. Thus, we believe that the rate of chalcocite oxidation in heaps is governed by sideways diffusion rather than downward migration. Column experimental results have been reproduced with a comprehensive heap-modelling tool. The model predicts that by simply changing the length of the average diffusion channel from column conditions (a few cm) to heap conditions (tens of cm), extraction times can change from weeks to years under otherwise identical conditions.

Jan 1, 2003

By Jafar Safarian

Bauxite is the main raw material used for the production of alumina (Al2O3) through the well-known commercial Bayer process. This process has significant challenges such as limitation in using low-grade bauxites as they contain significant amounts of impurities such as Fe, Si, Ti. The Bayer process residue, which is known as red mud, is also a global environmental challenge due to huge amount of this low value residue production. An alternative sustainable process with high potential to solve these problems and produce valuable and consumable by-products is a pyrometallurgical-hydrometallurgical process in which the low-grade bauxite ore is treated through a smelting-reduction process, yielding iron alloys and a calcium-aluminate slag. Alumina is then produced from the slag by hydrometallurgical treatment. In the present work, the reduction of pellets produced from different bauxite ores by hydrogen is studied and it is shown that complete iron oxides reduction is possible. Further smelting and smelting-aluminothermic reduction of the reduced pellets show that iron and silicon ferroalloys can be produced, in addition to a proper slag for alumina extraction.

By J. G. Peacey, P. Hancock, R. -Q. Li

A pyrometallurgical process for the direct recovery of zinc from zinc concentrates and zinc/iron residues has been proposed and tested extensively by Noranda. The process consists of smelting bone-dry zinc containing materials (sulfide concentrates and secondary zinc/iron materials) in a molten iron oxysulfide bath to volatilize metallic zinc into a SC^-free offgas. Sulfur contained in the feed materials is fixed as an iron oxysulfide matte for disposal. Thus, this process not only is capable of treating zinc sulfide concentrates and secondary zinc materials simultaneously, but also eliminates the need of sulfuric acid production. Detailed thermodynamic analysis and experimental test work are described in this paper.

Jan 1, 2000

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015

By P. F. Kerr

This is not a conventional professional paper. It deals mostly with personal experiences. These concern a background in applied mineralogy. Your committee asked me to do this. I accepted with a California enthusiasm which has since diminished with the approach of a Chicago winter. Nevertheless, I wish to thank your committee and also to apologize in advance for omissions and inadequate statements, as such a paper must possess. My introduction to applied mineralogy took place in 1922 at Stanford University. Physicists had recently demonstrated that crystalline powders would reflect x-rays in a systematic manner. Professor A.F. Rogers sug¬gested that significant x-ray reflections might be obtained from powdered opaque minerals. With the aid of Professor D.L. Webster in the Physics Department, I constructed an x-ray diffraction outfit. It was a crude affair, but it worked. Starting with 1924, we secured recognizable patterns of a goodly number of ore minerals (1,2,3). Today x-ray diffraction outfits are common, and a card system of mineral identification is constantly used.

Jan 1, 1981

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By Byung-Su Kim

The reaction between calcium sulfate and hydrogen is of interest both as a means of regenerating calcium sulfide as a reductant of sulhr dioxide to elemental sulhr and for producing elemental sulhr from gypsum. This reaction was investigated using a thermogravimetric analysis technique in the absence and presence of nickel catalyst. The reaction temperature was varied between 973 and 1153 K, while the hydrogen partial pressures of 12.9 - 86.1 kPa were utilized. At 1073 K and a hydrogen partial pressure of 86.1 kPa, 60 % of the original calcium sulfate in the absence, and 95 % in the presence, of the nickel catalyst was converted to calcium sulfide in one hour.

Jan 1, 1999

By P. A. Botha

The coal seams in the Waterberg basin occur in correlates of the Vryheid and Volksrust Formations as developed in the main Karoo basin. In the Vryheid Formation, five thick seams of predominantly dull coal are present, whereas a multitude of thin, lenticular seams (a few millimetres to 2 metres}, predominantly of bright coal, are developed in the overlying Grootegeluk Formation. During exploration, the coal seams were divided into 11 zones. Analytical data on float and middlings fractions (RD less than 1.40 and between 140 and 1.80, respectively} were used mainly for stratigraphic correlation of the zones in the Grootegeluk Formation. The affinities of the major and trace elements for different mineral phases and/or organic material are discussed on the basis of correlation matrices and vertical variation diagrams. Titanium and vanadium clearly show some degree of organic affinity. P 205' AI203 and alkaline-earth elements are also positively correlated by the presence of goyazite in the coal. This type of investigation gives an indication of the degree to which undesirable elements like P and S can be removed during coal beneficiation, of which coal zones are unsuitable for the production of metallurgical coal on account of a high content of these elements, and to what extent the blending of different coal zones is required to keep the concentration of these elements within acceptable limits.

Jan 1, 1991

By Alexandre Bonan

This paper reports the results of a kinetic study on the oxidation of free cyanide and Cu-cyanide complex ions with HO,. The variables and respective ranges studied were the following: [CN] total =10 - 500 mg/l; pH=10-11; (H2O2/CN) mole ratio = 1- 3; (Cu/CN) mole ratio = 0.10 - 0.25. The results were interpreted by a semi-empirical model that incorporates the useful oxidation reactions and the parallel alkaline decomposition of H2O2

Jan 1, 1994

By Kazuyoshi Sato, Keizo Uematsu, Nozomu Uchida

"Confocal fluorescence scanning laser microscope was applied to characterize the surface flaw of ceramics in great detail. A high potential -of the characterization technique is presented first. Then the technique was applied to clarify the relationship between the flexural strength of ceramics and the surface flaw. This kind of direct information of surface flaw should be essential for the fundamental study in this area, but has been lacking. The examination revealed that large defects are present on the machined surface of ceramics. Their size is consistent to the flexural strength measured on the material. The characterization tool was also applied to examine the formation of surface flaw in machining of ceramics.IntroductionClarification of fracture origin should be the starting point in the study on strength in ceramics. However, this task has been extremely difficult in some ceramics, such as an alumina ceramics. It may break from both internal and surface flaws. The former should reflect the quality of production process and the latter the machining. Examination of surface flaws should be very important for developing a better machining method for ceramics. The knowledge may valuable for establishing a better production process also.ExperimentAlumina Referceram (JFCC) was used as samples. They are cut to size of 3x4x40mm, and the surfaces were ground to meet the requirements of testing method for flexural strength of fine ceramics, JIS R 1601. They were soaked in an aqueous solution of fluorescence dye and evacuated with an aspirator for an hour to allow the solution penetrate into surface flaws. After excessive solution remained on the surface was removed by gentle washing, the specimens were dried at 120°C for 48 hours. The 4 point bending mode was applied to measure the fracture strength."

Jan 1, 2000

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By Henry L. Ehrlich

This survey compares bioleaching and biobeneficiation by autotrophic bacteria with that by heterotrophic bacteria and fungi Some physiological principles are reviewed. Advantages and disadvantages of autotrophic and heterotrophic leaching are discussed. Principles of anaerobic leaching by autotrophs and heterotrophs are introduced. and the advantages? over aerobic heterotrophic leaching are discussed. Examples of useful organisms in the autotrophic and heterotrophic categories are cited.

Jan 1, 1991

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340'C by the two probe method using an ultra high resistance meter. The k value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it mouutuniocally increased from 10-5 to10-4 A' 1 cm-1 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the K value. The k value increased with the increase of Na proportion in the melt. For a 10mol% Na doped sulfur melt it was as high as max ~30 A 1cm -1 above 180 C under the irradiation of of ultrasconics.

Jan 1, 2003

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By M. K. Mohan

Lead recovery from process solutions contributes not only to the conservation of resources but also clean environment. Zeolites are natural aluminosilicates, which finds applications as catalysts and in wastewater treatment. In the present investigation, studies were taken up on the processing of Pb from process solutions by zeolites. Effects of pH of the solution, time and type of zeolite viz. chabazite, mordenite, erionite and clinoptilolite on the removal of Pb from solutions was investigated. Rate of sorption was found to depend on the pH of the solution and about 99 pct. recovery was observed at pH 6. Optimal conditions were established for the maximum recovery of lead from process solutions. Possible sorption mechanisms were proposed. The calculated adsorption constants calculated from Langmuir and Freundlich equations showed that the adsorption of lead on chabazite was strong.

Jan 1, 1999

By Kurt A. M. Westerlund

The basic function of primary gas handling downstream non-ferrous pyro-metallurgical processes is cooling hot sticky gases to treatable temperature levels (e.g. entering ESP). That means managing efficient the critical gaseous components from a molten via a sticky to a solid phase. The article outlines the modem gas cooling methods combined with efficient heat recovery. Examples of the alternative use of recovered steam energy are outlined; as e.g. drying of concentrate and power generation. The heat transfer impact of the insulating dust is called fouling and circumstances causing fouling are described. Modem cooling surface design and cleaning techniques to keep fouling in reasonable limits are described. Leakage- and false air ingress into the gas handling lines often limits smelting capacity. The objective is generally to minimize the infiltration of air but it still takes place at open interfaces (e.g. at reactor hood, feed port). Leakage air at furnace roofs for example can be reduced to a minimum by adopting the pressure gas sealing used at present In-Bath-Lance furnaces. Modernization and optimization methods to de-bottleneck existing waste heat boiler gas cooling capacity by highly efficient surface cleaning systems and false air avoiding (e.g. bundle roof boxes, dust discharge) are detailed described.

Jan 1, 1999

By P. A. Davidson, D. J. Short

"In this paper we describe a 'non-contact' electromagnetic nozzle suitable for sprayforming and gas atomization processes. In such processes there is a need to control the flow rate and diameter of the liquid metal jet whilst minimising contamination of the stream. This can be achieved using an electromagnetic valve, which partially levitates the jet in freespace, using a segmented cylinder surrounded by an induction coil. This valve will significantly enhance the quality of the titanium alloys and nickel-based superalloys used in sprayforming and gas atomization. This paper describes the design and test of a laboratory prototype valve based on experiments performed with liquid tin.1. Introduction In many industries there is an increasing need for clean, high quality metals and alloys based on titanium and nickel. Two important processes are: 1) Spray deposition which allows the liquid metal to be converted to a near-net shape, thus alleviating the need for subsequent forging and extensive machining and; 2) Powder production of titanium by gas atomisation.In centrifugal spray deposition of titanium (see figure 1) the metal is induction melted in a cold crucible. The crucible consists of a number of water-cooled segments, which allows the high frequency magnetic field of the coil to pass through the crucible, and into the melt. The charge is melted by the induced eddy currents. Locally at the crucible walls the liquid metal solidifies, and is contained within a. 'skull' of its own solid, thus reducing contamination from the crucible wall. Once melted the metal is poured through an electrically heated graphite nozzle and into the spray forming chamber. The principal limitation of the process to-date, however, is that it currently uses a graphite and /or ceramic nozzle to direct the flow of liquid metal to the atomizing disk and as such there is considerable risk of nozzle erosion with inevitable effects in terms of contamination of the melt stream and variability in flow conditions. In this research programme we develop a. non-contact electromagnetic nozzle, which will totally eliminate refractories and/or ceramic materials from the melting and casting process. This will greatly enhance the technological capabilities of sprayforming and gas atomization processes."

Jan 1, 1999

By M. K. Alam

Chemical Vapor Deposition (CVD) processes are currently attracting special attention in materials processing. CVD processes are now used to produce special materials in the form of thin films, coatings, composites, and optical fibers. This process produces material of high purity, in complex shapes, and in a variety of microstructures. It is a capital intensive process, involving use of high cost raw materials. Modeling simulations have the potential of reducing the time for CVD . process design, and the need for experimentation. Modeling would, therefore, appear to be an attractive option for producing a product of acceptable quality. At Ohio University, progress has been made in modeling of CVD processes, specially in the areas of optical fiber preform fabrication, and fiber coating.

Jan 1, 1990