Search Documents

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Thomas Rymer

Mathematical modelling of mine subsidence measured at 21 locations in Pennsylvania and northern West Virginia allows for the refinement of current methods of predicting maximum land subsidence associated with longwall coal mining. This new method (RYBAD model) is an extension of that provided by Tandanand and Powell (1984; TP Model). The RYBAD model accomplishes more accurate subsidence predictions (error typically less than 10 percent) for a greater range of mining and geological parameters through the recognition of the following: 1) subsidence increases at a decreasing rate (curvilinear relationship) with greater overburden thickness up to a critical value beyond which subsidence decreases; 2) subsidence is strongly influenced by the stratigraphic proximity of strong rocks to the coal (size of potential caving zone); and 3) subsidence index is related to overburden thickness by a family of curves, each for incremental variations in the effective percentage of strong rock in the overburden.

Jan 1, 1988

By Robert R. Thompson

Retreat pillar mining is highly productive but dangerous. The primary danger during pillar removal is premature caving of the roof. Because the safety of the miners is dependent on successfully controlling the roof, the roof must cave in a predictable and dependable manner. Temporary support during retreat is usually obtained by setting posts. They are set manually by a miner working in a dangerous area. A solution to this problem would be a system which could set and retrieve roof supports remotely and safely. The Bureau of nines has developed a remotely operated Mobile Roof Support (PIPS) machine which will place and retrieve temporary roof support. Two PIPS machines were fabricated under a cost-sharing agreement with Southern Utah Fuel Company and mining equipment manufacturer. Each machine carries four 50-ton jacks and is remotely- Controlled by radio. The machines are presently being used by Southern Utah Fuel Company under a long-team cooperative agreement. Not only have there been material and manpower cost savings in not having to set posts, but also the time saved bas resulted in increased productivity. The projected costs of mass-produced machines with tethered remote control rather than radio remote control are estimated at $150,000 each. The radio remote control is more expensive and is considered an optional extra.

Jan 1, 1986

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The theological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

Jan 1, 2003

By Maynard O. Serbousek

The mechanics of load transfer of fully-grouted roof bolts in coal mines has been investigated in laboratory and analytical studies. The purpose of this research is to increase the understanding and better interpret data from pull tests which are routinely performed in the field. Laboratory work includes variation of bolt length, hole diameter and grout type in pull tests. Four-foot bolts were tested in holes of 1- and 1-3/8-inch diameters. Both polyester resins and inorganic grouts were used as the anchorage medium. The bolts were strain gauged at six locations to observe the rate of load transfer from the bolt to the rock mass when a force was applied at the bolt end using standard Jack pull testing procedures and equipment. Analytical studies using closed form solutions and finite-element techniques were compared to experimental results. The models are for the elastic regime only but do include slip elements. A detailed analysis of the load transfer mechanisms from the bolts through the grout to the rock mass is presented.

Jan 1, 1984

By Leigh J. Wardle

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goat behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales

Jan 1, 1992

By M. V. Kurlenya

The experience of application of geomechanical investigations for substantiation of extraction of undermined ore deposit in the north of Siberia is discussed. The finite element method was used for forecasting the state of massif during the development of mining works. The results of calculations were compared with the experimental data of observations in situ for evaluation of authenticity of numerical modelling.

Jan 1, 1990

By Kot Unrug

Fully grouted tensioned bolts provide a desirable compressive of laminated roof and bondage along the entire bolt length, at the same time the entire surface of the hole is protected against penetration of moisture. This is particularly important in shale strata, where, when left unprotected by a partial grout column, moisture penetrates to the annular space, and weathers rock around the bolt hole, having an easy access to the bedding planes which are strongly hydrophilic. The most desirable are thrust tensioned rebar bolts that can be installed with one procedure step, and can secure a desired pre-stressing. Such bolts have a forged conventional head and offer no hazard to miners in low clearance mines, whose number increase constantly due to the depletion of reserves in thicker seams. The presented field-testing program has been based on instrumented bolts allowing for monitoring of tension at installation and at a chosen time interval after. The tested system is based on rebar bolts installed with two speed Fosroc resin (fast at the top and stow at the bottom), and mechanical compression by the bolting machine at installation. Combination of several different washer -- plate arrangements have been tested. The results are reported with their interpretation, and recommendations directly towards strata control requirements, as well as the operational considerations for efficiency of installation.

Jan 1, 2002

By Michael Gauna

Ground fall injuries and fatalities in United States underground coal mines have shown a diminishing trend. Advances in bolting and standing support systems have led to improved safety in underground coal mines. However, the Crandall Canyon Mine disaster in 2007, in which 9 individuals were fatally injured as a result of a widespread collapse, emphasized that proper mine design is a critical issue that must be addressed. The Mine Safety and Health Administration (MSHA) has instituted technical review procedures structured to facilitate the implementation of safe mine designs in underground coal mines. The technical review process and the typical information required are outlined in this paper. The range of mining situations that lead to a technical review, common design methods submitted for review, and their relevant guidelines and limitations are also discussed. Additionally, the relationship between design criteria and mine site historical experience is discussed.

Jan 1, 2011

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

By K. F. Unrug

A new testing technique for the determination of the rock strength from portable rock tester is proposed. It is a quick and economical method that can determine the rock strength with reasonable accuracy in different conditions. This method is based on the application of portable rock tester working at the principle of forcing steel ball into the rock surface. The correlation between laboratory measured compressive and/or tensile strength and rack tester reading has been determined in terms of the three-controlling parameters: (1). diameter of indentation &'the testing sample, (2). diameter of indentation-on the reference bar, (3). Brine11 hardness number of reference bar.

Jan 1, 1990

By M. O. Serbousek

In 1975 the Bureau of Mines Spokane Research Center began a series of laboratory and field tests to investigate the feasibility of developing a substitute for the organic chemicals used in resin roof-bolting systems. An inorganic system, comprised of calcinated gypsum, an accelerator, and microcapsules of water was developed and patented by the Bureau in 1977. The system has several advantages including economics, non- toxicity, nonallergenic, inflammability, and is not based on petroleum products. Two roof-bolting systems utilizing inorganic cements are under development at the Spokane Research Center--a cartridge system, using the microcapsules of water and accelerator, and a slurry system, using a mix-inject method which combines dry powder cement with water for simultaneous injection into a predrilled roof-bolt hole. Several underground field tests have been conducted in eastern coal mines. Test results indicate that inorganic cartridge systems are adequately supporting mine roof in several test sections. Economic potential for the bolt systems appears favorable.

Jan 1, 1981

By Nikolaos Polysos

To drive and utilise gate roads economically requires accurate planning and risk assessment considering the variable geomechanical requirements. The geomechanical part of roadway planning is secured by geotechnical investigations of drill cores and geophysical borehole logging. The rock specific parameters determined in this way allow a statement about the quality (defomtation and strength characteristics) of the rock that has to be cut across. They set up the basis for a standardised rock assessment. Combined with the prevailing rock mechanical situation, technical boundary conditions for advance and support techniques can be identified already in the planning phase. Detailed geotechnical investigations prior to the planning and driving of roadways can lead to a technically and economically optimised roof support system. Geotechnical core logging and a standardised assessment scheme based on the data acquired will be introduced. Geophysical borehole logging methods provide additional physical data. Different methods and their validity, which may lead to a further improvement of the planning reliability, will also be presented. The geomechanical information gained and their relevance fir the planning will he illustrated. Keywords: rock classification, geotechnical rock parameters. geophysical well logs. support planning

Jan 1, 2002

By M. Guana

Island Creek Corporation is predominately an underground mine operator deploying room-and-pillar and retreat longwall mining methods for extracting coal. Wide variations are encountered in overburden depth, stratigraphy, and insitu stress fields. This requires major adjustments in mine design among mines and occasionally within a mine. Simple rock mechanics principles are utilized in mine design to optimize safety and productivity. Physical observations and micro deformation monitoring of roadways are the primary techniques employed. Pillars and artificial support systems are the primary design elements modified. The specific case histories reviewed in this paper include narrow panels with high extraction for conventionally mined rooms, pillar sizing for longwall gate entries at great depths, and bolt type selection for difficult ground conditions.

Jan 1, 1988

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By David Newman

The latest version of the Surface Deformation Prediction Software (SDPS) package is presented through its application to a number of case studies. The package now exploits all the benefits of the Microsoft Windows platform and has a direct interface to CAD software, thus facilitating input and output. Also, the package features advanced calibration routines to handle predictions over specific regions. The case studies presented highlight the features and capabilities of the new package.

Jan 1, 2001

By Tim Ross

J. M. Huber Corporation's Quincey Mine. an underground limestone mine located near Quincy. Illinois, has operated successfully and safely for many years utilizing roof bolts on a very limited basis. Over the years, the mine had experienced several rool falls that did not result in injury to personnel. Nearly all of the roof falls were limited to the first 2 feet of the massive limestone roof. Investigation of the falls indicated the major contributing factor to these roof falls was a randomly occuring thin. horizontal clay layer in the immediate roof. Over time, separation would occur at the clay layer. causing the root to sag. and eventually causing the root to fail. J. M. Huber Corporation contracted with NSA Engineering. Inc. to assist in a study to determine the effectiveness of Ground Penetrating Radar (GPR ) for locating these potential root fall areas so that mitigating action could he taken prior to roof failure. Multiple tests were conducted in areas of known roof conditions. GPR accurately predicted the existence or absence of root separation up to 1.5 meters into the immediate roof for 100 % of the known lest site conditions. As a consequence of this successful studs, J. M. Huber Corporation has used GPR to evaluate roof conditions at both its Quince and Marble Hill Mines.

Jan 1, 2002

By Jay Keng

During the construction of shaft on the fractured and weak rock strata, the stability of construction plays an important role. This study includes earth stress estimation, support method, and stability analysis. Stresses on the site of three shafts include structural residual stresses, earth pressures, and hydrostatic pressures were determined. The basic method of estimating the support strength is dependent upon the' size of the plastic ring after rock excavation. During the construction of the shaft, geotechnical measurements, physical properties of the rock, and the change after excavation have to be evaluated again. Geology and construction methods need further consideration.

Jan 1, 1988