Search Documents

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By C. P. Mangelsdorf

The success of the Birmingham roof truss (Figure 1) in supporting some difficult roof conditions, particularly in the Illinois coal basin, has given impetus to the development of a number of alternate schemes. These schemes attempt to alleviate two major problems with the Birming-ham truss, namely, the time required for installation and the cost of material. Because of the difficulty of drilling angled holes and the number of different pieces of hardware which must be handled manually, most operators have been unable to install Birmingham trusses in the cycle and have had to schedule truss crews during the maintenance shift or whenever they would not impede production. Due to this delay the truss has traditionally been viewed as a supplemental form of roof support. In fact, the truss might qualify as primary support and replace at least two bolts if it could he installed in the cycle (and MSHA would accept it as an alternate in the roof plan.) [ ] Figure 1. The Birmingham truss. Two attempts to deal with the first difficulty have sought to streamline the truss hardware while preserving the essential character of the Birmingham truss. One of these, by Peabody Coal, is reported elsewhere in these proceedings by C. Bollier. Another is a contract issued by the Bureau of Mines to Bendix Corporation for the development of a machine, particularly suited for use in low coal, which will automate many of the operations currently executed manually. This machine is expected to be ready for field testing by fall of 1982. Once in place, a truss installed by either of these schemes will interact with the roof in the same way as a conventional Birmingham truss. An alternate approach has been proposed by several different manufacturers independently. Although the hardware details differ. the essential idea consists of two angle bolts, the heads of which are connected by a horizontal chord tightened to some pre-determined tension. Figure 2 shows the generalized concept and does not depict any one of the four systems proposed. The advantage of this scheme is that the angle bolts can be installed and tightened in the cycle, and as bolts, immediately satisfy the roof control plan. The horizontal chord can be added later to achieve almost any initial desired roof loading, the limits of which are defined below this scheme is referred to here as the angle-bolt truss. Because of a fundamental difference in the way in which load is transferred between chords, this design does not interact with the roof under subsequent loading in the same manner as a Birmingham truss. The purpose of this paper is to examine this fundamental difference and its consequences. [ ]

Jan 1, 1982

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By T. L. Dobecki

As a means of demonstrating the effectiveness of reflection seismology in determining continuity of coal seams, three U. S. field projects are reviewed. The three projects involve coals of varied thickness (2-14m) and age (Pennsylvanian to Eocene) from three coal areas of the U. S. (Pennsylvania, Wyoming, and Washington). Each project also employed its own particular seismic technique, recording system, and seismic energy source although all are considered state-of-the-art, high resolution, digital seismic surveys. Project 1 (thin, Pennsylvania coal) sought detection of sand channels using dynamite and standard in-line (2-D) seismic technique. Project 2 (thick, Wyoming underground coal gasification) involved a gas-explosion (Dinoseis) source with areal (3-D) acquisition methods. Project 3 (thick, Washington underground coal gasification) employed a shotgun-type source and standard in- line methods. Data processing was handled by different contractors for each project. Each project was successful in accomplishing its own particular objective; however, data quality and interpretation seem to be more a function of thickness of the target seam, complexity of the overburden, and processing contractor than a seismic source, acquisition scheme (2-D versus 3-D), or recording instrumentation.

Jan 1, 1981

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Lance R. Barron

The U.S. Bureau of Mines, in cooperation with a central Utah coal .mine operator, began a study in July 1988 into longwall gateroad designs applicable to deep, bump- prone mine conditions. Prior to the study, four adjacent longwall panels, incorporating a variety of panel entry configurations using "yielding' chain pi liars, experienced severe bumps and coal outbursts at the face and in the tailgate pillars during panel extraction, resulting in several lost-time accidents and a fatality. To quantify those factors primari1y responsible for bump occurrences during panel retreat, a field investigation was initiated to confirm the anticipated performance of a two-entry gateroad system employing a large, nonyielding chain pillar design. Hydraulic borehole pressure cells and roof-to-floor closure [convergence) measurement stations were installed to monitor gateroad abutment loading and entry closure during panel extraction. Study results indicate that very high confinement of the coal seam by strong roof and floor members existing across the entire property, in conjunction with overburden depths in excess of 1.600 feet, provides for bump-scale energy storage in not only gate pillars, but along the entire periphery of the active mining area. Insufficient gate pillar designs were also identified as possibly enhancing the occurrence of bumps in the tailgate and adjacent face areas.

Jan 1, 1990

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Douglas C. Peters

Part of the ground control research at the U.S. Bureau of Mines is involved with improving ground control data collection and analysis methods. A geographic information system (GIs) is being used within this research effort to standardize the data collected and provide a common graphical and tabular format and analysis system for researchers to access information on underground coal mines. In addition, GIS's can perform relational analyses on multiple map and tabular data sets which are not possible through map-creation or CAD packages or through data bases alone. In addition to standardizing ground control analyses, there is an increasing need for rapid analysis of ground control data in connection with increasing production rates at longwall mines. The examination of a large number of interrelated parameters and their impact on short-term mine safety and productivity under the time constraints imposed by rapid production requires computer-aided techniques. A GIs provides the means to quickly, quantitatively, and reproducibly evaluate mine-wide conditions. This overview of GI8 techniques for mine data integration and analysis, using a mine in Colorado as an example site, will cover the input of data into a GIs, including mine-wide monitoring system data and general data such as roof control plans and geology. The methods to geographically reference these data sets and retrieve and combine them also will be covered. Automation of such processes briefly will be reviewed to allow future users to automate their mine data analyses.

Jan 1, 1990

By Jim Sandford

The South Bulga Colliery longwall operation, owned and operated by Cyprus Coal Australia. Oakbridge Pty. Ltd., and located near Singleton, NSW, is currently operating under an average 80-ft-thick (24-nt) sandstone unit residing immediately above the coal seam, resulting in sudden and severe face weightings. To date, nine severe weightings have occurred at the property (within Panels 3, 4. and 5), three of which resulted in face closures accompanied by significant equipment damage and several weeks of downtime. The remaining six events nearly resulted in face closures, incurring single-pass vertical convergence of up to 8 in (200 mm) along the pan line. In an effort to mitigate and/or eliminate the occurrence of these severe weighting events, mine management has established an in-house program to immediately address the geotechnical and operational mechanisms underlying rapid weightings, as well as specific measures to mitigate these events on future panels. In support of this in-house effort. NSA Engineering Pty. Ltd., is assisting the engineering staff at South Bulga in developing a more aggressive face monitoring program. The aim of this program is to provide weighting occurrence predictions sufficiently ahead of time to ensure that operational controls are optimized prior to attempting to mine through potential weighting areas. This paper reviews the occurrence of weightings to date at the South Bulga Colliery as well as the latest developments in shield monitoring technologies to forecast these events in near-real time.

Jan 1, 1999

By Liang Yin-Huai

In Fuxin Coal Mines, there are more than 20 million tons of coal buried under seasonal streams. The coal seams are mostly shallow. We have mined more then 50 mining blocks distributed in 5 coal mines. Their natural conditions are different, and the consequences are also more or less different. However, no stream-water-inrush accidents under regular mining conditions are the same. There were 3 exceptions. They were caused by unexpected roof caving which made valleys or alluvia subside as funnel-like cavities and let in inrush of stream flow. The key to our success in mining shallow under-stream coal seams, according to our analysis, is that valleys or alluvia subside gently and basically evenly with contractible tension fissures and that fissures both in valleys or alluvia and in rock seams are blocked up or sealed by cohesive deposits either from alluvia or rock. This paper treats: (1) some typical illustrations of mining shallow coal seams of different occurrences under streams of different sizes, flowing capacities and valley structures, (2) observations of the height of caved and fissured zones and subsidence of valleys or alluvia, (3) observations of underground water flow before, during, and after mining and the fluctuation with respect to stream flow, (4) observations and analyses of blocking up of fissures caused by mining, and (5) feasibility of mining shallow under-river coal seams.

Jan 1, 1990

By Maleki. Hamid

The U.S. Bureau of Mines implemented an inte¬grated static and geophysical monitoring program in a southern Wyoming mine to study changes in seismic wave propagation properties in roof strata. The purpose was to develop techniques to assess roof stability problems. The work consisted of record¬ing deformation and stress histories and calcu¬lating seismic velocity profiles. In addition. geology and roof conditions were mapped; the in¬struments were initially installed at the develop¬ment face; monitoring continued until the mecha¬nized retreat face retreated within 60 m of the instruments. Mining geometry consisted of a three-¬entry gate system using 5.2-m-wide pillars at depths of 426 m. Results were analyzed using stan¬dard history plots, velocity tomographs, and numer¬ical modeling techniques. Changes in velocity. frequency, amplitude, dynamic elastic modulus, and dynamic Poisson's ratio were related to roof defor¬mation, fracturing, and support requirements. A reduction in seismic velocity of 17 pct occurred after 60 mm of roof deformation following installa¬tion of supplementary support. Static measurements revealed significant dilation in the mine floor, spreading to the pillar and the mine roof. Failure was initiated in the floor as a result of uniform pillar penetration.

Jan 1, 1993

By Chao-jiong Hou

The necessity of using tensible rockbolt in the roadway with soft rock, high in-situ stresses, mining influence and other complex conditions was discussed, the structures of three kinds of tonsibte rockbolt and design principle were introduced in this paper. The tests of analogue material simulation under plane strain condition and underground industrial tests indicated that the effect of controlling deformation surrounding roadway by use of tensible rockbolt was good.

Jan 1, 1989

By Paul A. Lu

This paper proposes an unconventional, simple, and practical method of measuring mining-induced around stresses with hydraulic borehole pressure cells. The method is a direct ground stress measuring technique. It does not require the value of deformation modulus for back-calculation of stresses; instead, it directly measures the ground stress in situ. The applicability and practicality of the technique are shown by two case studies. The technique may be applied to monitoring a stress build-up that may lead to mine roof failure or to rock and coal outbursts.

Jan 1, 1984

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Erdal Unal

In order to define the support parameters, by use of empirical approaches, it is particularly important to analyze the rock-load height that should be controlled by supports. The controlling mechanism however, depends on the type of support used there- fore, the rock loads should be treated differently. In this paper, an empirical equation is introduced which relates the rock-load height (ht) to a quantitative rock quality index (REIR), and roof span (B) as fallows:

Jan 1, 1986

By T. N. Singh

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of mechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 MPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

By Pier Paolo Manca

The investigated area lies close to a large town and covers an area of about lkm2. The mine was worked at depths ranging from 5 to 100 meters but mining operations actually ceased some 50 years ago. There are seven coal seams, each one to two meters thick, overlain by sedimentary rocks in a strongly faulted area. Different kinds of subsidence have occurred, crown holes, shallow depressions and hummocky ground. The results of rock mechanical characterisation (RMR method) in the area have been used to define three different types of numerical model (FLAC 2D). A large numbers of simulations has been performed to solve three different problems at three different scales: to determine the, mechanical properties of the roof rock and overburden involved in the subsidence process, to assess the crown hole subsidence potential and to define the properties of the beam foundations.

Jan 1, 1999