Search Documents

By Linda K. Killoran

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomographic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First¬arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

By J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can he predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential.

Jan 1, 1998

The challenge of planning to minimize interaction effects in multi-seam mining is compounded by the difficulties inherent in extrapolating essential geological and spatial data between sampling points. To predict the effects of ultra-close mining on lower seam entry stability, simulated mine openings were studied using finite element analysis and body loaded photoelastic models. Both symmetrical and unsymmetrical loading was used to represent stress fields generated under multi-seam conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Stability predictions require precise definitions of geologic and spatial data, which could not be accurately defined by interpolation between sampling points. To overcome this problem an expanded roof stability model, SESAME2, was developed to incorporate reliability concepts based on Monte Carlo sampling. The model was demonstrated in terms of variations of innerburden thickness using a case study.

Jan 1, 1994

The U.S. Bureau of Mines (USBM) has developed the coal Mine Roof Rating (CMRR) to aid in ground control. This paper describes the application of the CMRR at four coal mines operated by a major U.S. coal company. The mines are widely separated geographically, and cover a wide variety of geologic conditions and mining methods. The study found that the CMRR was a useful predictor of roof performance. In mines where the CMRR varied, and other parameters held constant, roof falls were associated with low CMRR values. Important similarities in roof performance were found in mines with similar CMRR values, despite radically different geologic environments. The analyses also indicated that statistics can be used to evaluate ground control performance. For these mines, a "roof fall probability" can be estimated from the CMRR and the intersection span. A spreadsheet program has been developed to facilitate treatment of CMRR data, and it is briefly describe

Jan 1, 1994

By Mingju Liu

In this research, we measured fractal characteristics of over ten typical outburst areas on different scales and related them to their outburst proneness, in attempts to provide new methods for outburst prediction. It was shown that both faults and folds follow the power law on coal basin scale, mine scale or mining district scale, whichever it is. Fractal dimensions are appropriate indices to describe geological structures quantitatively. Preliminary relationships have been established between outburst proneness and fractal dimension. Comparisons have been made among fractal characteristics and degrees of outburst proneness on all three scales. The results indicate that multi-scale assessment of outburst proneness can be made based on fractal measurements independently or supplemented by other assessment methods.

Jan 1, 2000

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Alan A. Campoli

"Pumpable crib support for longwall gates and ventilation bleeder entries is becoming more prevalent in United States coal mines (Figure 1). The pumpable crib selection and spacing design has been greatly refined by the full-scale testing conducted at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator. The peak load on 24-, 27-, 30-, and 36- inch diameter J-Cribs is, on average, 300, 400, 450, and 650 kips, respectively. Standard J-Cribs have useful deformation of approximately 8 inches. The maximum useful deformation can be extended to 18–20 inches with an exterior reinforcement layer or an interior double wall, for all four J-Crib diameters. J-Crib diameter is primarily limited by a maximum 4.5:1 height-to-diameter aspect ratio. Spacing is controlled by immediate roof stability, anticipated pillar deformation, and roof bolting practice. Approximately 500,000 J-Cribs have been successfully placed in 18 different United States longwall coal mines. The selection and spacing of the J-Crib utilized to date is summarized for each mine.IntroductionLongwall productivity and safety depend on ground stability in gate and ventilation bleeder entries. Numerous support technologies have been developed and employed in United States longwall mines since the 1990s to replace traditional wooden cribbing. Many, if not all, of these technologies have been evaluated at the NIOSH Pittsburgh Research Laboratory since the mid-1990s (Mucho, et al., 1999). The NIOSH Mine Roof Simulator has a 3,000-kip vertical load and 24-inch displacement capacity, which has facilitated in-depth analysis of complex multimaterial support technologies like the pumpable crib. The extreme cost and human exposure risk associated with modern longwall mining prevent the trial and error development that would have been required absent the Mine Roof Simulator research. As a direct result of this research, pumpable cribs are becoming a major component of the standing support industry, providing the peak capacity and extended deformation characteristics necessary for successful gate and bleeder support. Recent research by Zhang, et al. (2012) and others have defined the required performance characteristics."

Jan 1, 2015

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By J. R. M. Hill

The U.S. Bureau of Mines is involved in research to improve geological sensing (or geo-sensing) techniques. This paper presents results from field trials of two research projects concerned with new technologies for geosensing. The goal of the first project was to develop a "smart" roof bolter drill so that it could probe into roof rock to evaluate rock conditions. The goal of the second project was to modify an existing mine-wide monitoring system in a continuous mining operation so that the system could interface with geotechnical instruments to provide near real-time geosensing. Integration of this mine-wide monitoring system with the smart roof drill to collect, reduce, and analyze geotechnical data and the potential applications of the resulting technology in mining, are described.

Jan 1, 1992

By T. P. Mucho

Mine roof failure due to excessive horizontal stress has been recognized as a major cause of hazardous roof conditions in some mines. Stress measurements gathered by the U.S. Bureau of Mines (USBM) at 24 different eastern mines show horizontal stress to be typically 2 to 3 times as great as vertical stress. The focus of current Bureau work is to develop detailed design parameters to assess and control the effects of horizontal stress. To facilitate the recognition of horizontal stress effects and to easily determine principal stress direction without resorting to cumbersome, expensive, and time consuming field measurements, the Bureau has developed a stress mapping methodology. Stress recognition and direction determination are required to successfully employ a number of control strategies such as mine layout, mining sequences, and support optimization to control the effects of horizontal stress, thereby increasing the safety of U.S. coal mines. This approach has been used in other major coal producing countries, most notably Australia and the UK, and has greatly enhanced the safety of their mines (1). This paper discusses horizontal stress, directional based control techniques, and provides guidelines for the use of the stress mapping technique. A case study of a mine where the technique has been used is also presented.

Jan 1, 1994

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By John C. Stankus

From research started six years ago, a new design criteria has been developed for mine roof bolt systems This design criteria precisely and quantitatively determines parameters such as bolt length, installed tension, and spacing that will produce the Optimum Beaming Effect (OBE) OBE, a new roof control term, is defined as the roof beam that has no separation above and within the bolted range with the shortest bolt passible Utilization of this design criteria has shown that in many cases shorter roof bolts with higher installed tension can produce a much stronger beaming effect (Stankus, 1995) This paper will first present a brief deception of how the design criteria was formulated From there, actual case studies where the design criteria was utilized will be discussed In conclusion, current and future research efforts will be presented

Jan 1, 1997

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By D. F. Howarth

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in¬situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By Keith D. Koper, Kris L. Pankow, Derrick J. A. Chambers, Michael K. McCarter

"In a mining environment, high quality seismic event catalogs are often useful in interpreting local stress states and identifying areas with elevated ground control risk. Installation, operation, and maintenance of local/in-mine seismic networks, however, may be prohibitively expensive, and mine operators may not anticipate the need for seismic data until unusual mining conditions arise. If regional, generally public, seismic instrumentation could be used to reproduce the results generated by local/in-mine instrumentation to an acceptable degree of fidelity, it would be a valuable and inexpensive tool for mine planners and ground control engineers.In this study we apply subspace detection—a non-traditional seismic event detection technique—to data from a sparse, regional network. The process is employed to identify mining induced seismicity (MIS) from an underground coal district. The results are compared to a seismic event catalog produced by a local seismic array operating within the permit boundaries. Additionally, we analyze the performance of two different stations of the same sparse, regional network in identifying blasts at a surface coal mine for which we have a detailed blasting log. In both cases data from stations between 10 and 60 km away from mining activity are used. We also explore the trade-offs between the number of detections and the number of false positives, which is influenced heavily by detection thresholds and the number of stations used in the process.For the surface mine we are able to identify more than 90% of the production blasts documented in the blasting log. We also find that the detected blasts from each of the four active pits produce waveforms similar to one another. The results are not dependent on source-receiver distance, and by requiring detections to occur on both stations the number of sure false positives is reduced to zero. In the underground mining district we identify between 30% and 75% of the events detected by the local array, depending on the acceptable number of false positives and the source-receiver distance. We also find many events that were missed by the local array, showing that regional subspace detection can usefully augment traditional local catalogs. Moreover, subspace detection can provide an estimate on event location and classification using data from as little as one seismic station."

Jan 1, 2015

By Chris Mark

The Coal Mine Root Rating (CMRR) was first presented at this Conference nine years ago. Since Its Introduction, the CMRR has been incorporated into many aspects of mine planning. including longwall pillar design, rout support selection, feasibility studies. and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects iii South Africa. Canada. and Australia. The purpose of this paper is to bring the minim community Up to date with recent improvements and applications of the CMRR. The must important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are Jaw required: Fracture spacing (or RQD) Uniaxial compressive strength for axial Point Load Testing) Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program. which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR firm either underground or drill core data. Values from ninny locations can he saved in a single file. and an interface with Autocad allows CMRR contour plots to he integrated 11110 mine planning.

Jan 1, 2002

By Lawrence R. Artler

The North American Coal Corporation, its subsidiaries and other coal companies, have been mining the Pittsburgh #8 seam in Eastern Ohio for several decades. Underground mining by the "room and pillar" method, and more recently by longwall methods, have been practiced. This presentation deals with ground control problems and subsequent solutions to those problems for both mining methods. But first, let me briefly discuss some pertinent points about the geologic conditions of the coal seam near the southwest edge of the Pittsburgh Coal Basin. The Eastern Ohio region of the Pittsburgh Coal Basin is situated along the western edge of the unglaciated Allegheny Plateau. The local terrain is quite steep, with topographic relief of 430-500 feet being common. The coal thickness in the region ranges from 36"to 120", with the average being 60" in the areas being currently mined. Regional dip of the seam is toward the southeast in an amount of 10 to 40 feet per mile. A cross-section of the mineable seam generally consists of the main bench (60"), a rider coal (6"-12"), and a claystone parting (6"-12") for a total excavated height of 6-7 feet. Greater excavated height occurs where the fireclay floor is so soft and friable that movement of mechanical equipment breaks up the first 4-8 inches. Generally, the main bench and rider coal thin and become more variable toward the southwestern portion of the mining area. The rider coal also grades laterally into a coaly carbonaceous shale. In those areas where the roof coal can no longer be counted on to help support the immediate top, some of the main seam (6") is left to protect the overlying 8'-12' of mudstone/claystone strata. These strata are virtually non-bedded, highly slickensided units and are "hung in suspension" by roof bolts from a more competent limestone stratum above. These mudstone/claystone units are very susceptible to moisture and thus to the weathering cycles. The rider coal or 6" of the main bench is left in place to "seal" the mudstone/claystone units in Mains and Submains development. For many years, it was thought that the strength of the limestone member was detrimental in attempts to fully extract the seam by conventional means; however, longwall methods that have been more recently employed have broken the "myth" that the Redstone Limestone prevents full extraction of pillars.

Jan 1, 1984

By Kanaan Hanna

Abandoned mines pose a serious threat to public health and safety, as well as the environment. When active workings approach old mine workings, miners could encounter significant hazards. Additionally, the presence of mined-out areas or voids underlying residential/commercial properties, transportation, and infrastructure systems can cause subsidence issues ranging from differential settlements and sinkholes to catastrophic collapse. All these features can result in adverse impacts in terms of cost and public safety. Traditionally, mine void detection and related engineering investigations for mine subsidence risk assessment and mitigation have been greatly dependent on systematic drilling and grouting backfill programs. The unknown location and condition of abandoned underground mines represent significant challenges to geologists and engineers in accurately evaluating subsidence hazards and developing appropriate mitigation measures. A comprehensive, multi-phase mine subsidence investigation was conducted at an abandoned western U.S. mine site. The mine operated in an approximately 8-ft (2.4-m) -thick coal seam using room-and-pillar extraction from 1919 to 1922. The mine lies at depths ranging from 50 to 100 ft (15 to 30 m), and it is overlain by critical pipeline and utility corridors. Any future subsidence/ sinkhole that occurs beneath or adjacent to the corridors could pose a significant threat, specifically to the structural integrity of the pipeline corridor. Therefore, the engineering geophysical investigation was initiated to determine the potential subsidence risk. This paper describes a recent success achieved by using integrated engineering geophysics in subsidence risk evaluation. A summary of significant results with emphasis on subsurface characterization, mine workings and voids delineation, modeling analysis, and high risk zones identification and mitigation strategy is presented.

Jan 1, 2011