Search Documents

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By H. C. Juvkam-Weld

R. Michael Craig Mr. Juvkam-Wold's article is a timely and much needed presentation of the method of depressurization to reduce ground-water inflow into mine shafts. The article is very informative and discusses the effects of depressurization upon shaft inflows adequately. However, the article omits a discussion of another important benefit of depressurization: the reduction of potential for artesian burst or, as it is also called, floor heave. Confined aquifer systems (artesian aquifers) can contain water under several hunder pounds per square inch (psi) of pressure. For example, water levels at elevations of 455 m (1500 ft) or more above the top of the Westwater Canyon member of Reply by H.C. Juvkam-Wold In general, Mr. Craig's comments are useful and accurate regarding the potential benefits of aquifer depressurization. However, two of his points require further explanation since they may lead to a misunderstanding of my paper and its predictions. These refer to his comments regarding failure to account for storativity and to non-artesian conditions. Equation 5 is indeed Darcy's steady state equation. However, as a careful review of the appendix in this paper will reveal, I have used this equation to represent semi-steady state conditions. In other words, steady state conditions are assumed at any instant of time, but conditions may change gradually from

Jan 2, 1983

By Lyman H. Hart

Michiquillay is a major copper deposit situated about 70 km (44 miles) northeast of Cajamarca in northern Peru (Fig. 1). It occurs largely in quartz monzonite in a shatter zone produced by the intersection of northwest- and northeast-trending fault systems. The geology is described by Hollister and Sirvas (1974). The ore deposit was drilled in 1963-1964 by Asarco, with results indicating a resource of 575 Mt (634 million st) averaging 0.72% Cu-0.03% Mo. A decision to bring the project to production has been deferred because world capacity to produce copper has been more than adequate to serve world requirements since 1964. The chain of events leading to the discovery of Michiquillay was set in motion by a decision by the management responsible for the Chilete mine to undertake an investigation of the surrounding area for a possible supplementary source of mill feed to bolster its decreasing lead-zinc reserves. Chilete, located 100 km (62 miles) inland from Pacasmayo, is the most northerly, important mining project in Peru, and little was known of the mineral potential north and east of that point. Relatively unimpressive reports of Colonial silver mining had attracted little investigation, and little was known of the regional geology. One study by Benavides (1956) had been made of the Cretaceous in the region of Cajamarca.

Jan 1, 1991

By A. Fiszer

One of the major problems with deep Polish hard coal mines are deformations of close-to-wall galleries since they are necessary and must he kept open for emergency situations and are largely responsible for work disturbances. In order to ensure safe and effective working operations, it is necessary to often rebuild galleries which, apart from the inevitable stoppage of operations, is greatly disadvantageous for the operation of a mine. The largest problems with maintaining the galleries open occur in Lower Silesian Coal Field mines where sometimes it is necessary to reconstruct the galleries several times [(Fig. 1)]. In light of what has been said above, the aim of this article is to present the reader with methods and ways of determining deformations occurring in close-to-wall galleries. Squeezing or convergence of headings is only a portion of the entire process of ground movement caused by ground disturbance due to workings. The term "squeezing of headings" is to be understood as a shortening of the distance between a point set on the roof of a heading and the corresponding one on the floor. It is very important to know the rules governing the process of squeezing in a particular mining system since it affords possibilities to define changes of the process and its parameters at any moment for a given system. This is of utmost importance because convergence of a heading is one of the most significant manifestations of ground pressure which has already been proved by studies performed by Everling (1). On the basis of those studies it has been observed that there exists an almost linear relation between the rate of convergence and loading [(Fig. 2)]. This, in turn, means that the deformations of the already exploited portion of heading are proportional to the pressure changes.

Jan 1, 1982

By Mortimer J. Richardson

In the context of this session on "Practical Placer Mining," a projection of the present into the future first assumes that there is a future for Placers. The second assumption is that there is the combination of adequate reserves and a willing, mining investment source to finance placers. This paper will point out the opportunities on both assumptions, illustrating my positive position on the future of gold placers. In order to focus this paper more effectively, I have chosen GOLD as the subject mineral. However, it is recognized that much of the technology for exploring and mining gold placers has been applied to other alluvial deposits; including platinum, diamond, tin, and various industrial minerals (which are often referred to as "placers" though this contradicts historical definitions). Over the past 10 years I have presented several papers on the general subject of placers, most of which are listed under References. These have included topics such as exploration, evaluation, small-scale gold placer mining and decision-making, mining and processing equipment designs, and dredge-mining operations. In an attempt to identify the more promising, undeveloped placer potentials in the world I have usually mentioned the USSR and China but qualified them as being either inaccessible, or, politically difficult to obtain. However, with recent developments in the USSR, the obstacles appear to be somewhat diminished.

Jan 1, 1992

By Michael D. Loy

This paper examines the computerization steps of United Coal Company of Bristol, Virginia. OVERVIEW Producing close to 7,000,000 tons per year, United Coal Company is one of the most interesting mining companies in the east. Their approach to mining reflects a dedication to modern technologies and extraction methodologies. With varying amounts of production coming from four divisions (a fair amount of production comes from contract operators) and over a billion tons in recoverable reserves, United rests heavily on the planning and engineering efforts of a centralized engineering group. Although each division relies on its own engineering personnel for day-to-day management and operations, long range planning and reserve management is conducted at the corporate engineering level. This group, while extremely competent and efficient, is relatively small (7 people), when compared to the needs of a large mining company.

Jan 1, 1985

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By Debra W. Struhsacker, Jean Kiel, Jeffrey Thatcher

3.1 INTRODUCTION As heap leach precious metal projects become increasingly common in the United States, federal, state and local regulatory agencies are beginning to take a closer look at the short- and long-term environmental consequences of this recovery technology. From an operator's point of view, there is seemingly a confusing regulatory maze to be navigated and a plethora of permits and approvals to be obtained prior to commissioning a heap leach operation. The degree of difficulty associated with obtaining permits for a heap leach project depends largely upon the state in which the project is located. Permit acquisition is generally easiest in those states most familiar with heap leaching technology. For example, heap leaching is well understood in Nevada, and heap leach operations are relatively easy to permit, although permitting conditions in Nevada have recently become more stringent. However, many states are just beginning to become familiar with heap leach operations. Many of these states such as Idaho, Colorado, South Dakota, Oregon, Montana, Washington and South Carolina are in the process of drafting regulations and establishing guidelines for heap leach projects. In most cases, these regulations specify design and operating criteria as well as reclamation and decommissioning procedures. This chapter provides an overview of the regulatory and permitting aspects of heap leach operations. Permitting requirements for projects developed on federal land are discussed in detail. 'The state and local regulatory atmosphere and permitting requirements for various states are also presented. The chapter concludes with a generic permitting strategy. 3.2 KEY ENVIRONMENTAL CONCERNS The primary concern of most local, state, and federal regulatory agencies is the use, storage and transport of sodium cyanide (NaCn), and potential cyanide contamination of surface and groundwater resources. The toxicity of cyanide to people, fish and wildlife is also an important issue. Unfortunately, in the public eye, cyanide heap leaching has some emotional impacts similar to those associated with radioactivity and uranium mining. This perception and the general lack of understanding of cyanide can lead to unnecessary concern about cyanide contamination, further complicating the regulatory environment.

Jan 1, 1988

By G. Robert Ganis

The folded Appalachians are a physiographic province of eastern North America extending from Nova Scotia to Alabama. The province strikes through the state of Pennsylvania (see Fig. 1) comprising roughly 20 percent of the state and it is here that the focus of this paper will attend. The province is a thick sedimentary sequence which was compressed into a folded mountain belt by the Appalachian Orogeny which terminated at the end of the Permian. The stratigraphy contains both carbonate and non-carbonate rocks as a reflection of the depositional environment at any specific time and place during the Paleozoic geosynclinal accumulation. Although a great deal of variety and difference exists in the geology from one end to another, a common thread of structural and stratigraphic style exists. Carbonate rocks, limestones and dolomites, comprise a substantial percentage of the total Appalachian stratigraphy and are interbedded with clastic materials such as sandstones, siltstones, and shales. The carbonate rocks are extensively mined and collectively represent a vast economic resource.

Jan 1, 1983

By T. M. Storer

Much has been written and many discussions held on the virtues (and evils?) of a Company-owned motor fleet. Almost invariably these dialogues take a generalized form and thereby lose something since the individual circumstances, geography and philosophy - particularly in diverse industries, is never quite the same. In considering the nature of my remarks today, I felt a departure from the general approach might be in order, and in lieu of that, will attempt to present a concise picture of how we in the Lehigh Portland Cement Company view this problem and the steps we have taken in our efforts to solve it. At the outset a word may be in order about the Lehigh Company itself, what we do, and the problems that confront us specifically as well as the cement industry at large. We are primarily a manufacturer of portland cement operating 10 plants with a total annual capacity of about 23,000,000 barrels. We market this material in 30 states, shipping both from the plants directly as well as through a system of 18 distribution terminals. About 150,000 truckloads of cement are shipped to customers each year.

Jan 1, 1969

By R. H. Goodman

The development of techniques for separating minerals based on differences in their specific gravities is reviewed and their present applications in process technology outlined. Special emphasis is placed on the development, in Australia, of new models of the spiral concentrator. The mechanics of separation of spiral separators are stated, including the effects of operating parameters, Some of the traditional areas of spiral application are described, together with examples of new applications such as treatment of fine alluvials and tailings, separation of liberated minerals at coarse sizes and fine coal recovery.

Jan 1, 1984

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By Ted T. Biddle

The world energy crisis has created a greatly expanded exploration program for energy fuels. The demand for materials required for drilling operations such as barite, which is the primary component of drilling fluids, has increased proportionally. As in the case of many other minerals, existing high grade barite mines are no longer capable of producing the required tonnage. Consequently, exploration and development of lower grade ore bodies has been increased. The need to produce a high quality product at maximum recovery rates, along with the ever changing economics affecting both selling price and production costs has triggered accelerated research programs toward more sophisticated and efficient beneficiation methods. Taking into account the specific gravity differential between barite (4.5) and the normal gangue minerals such as silica and calcite (2.7), gravity concentration methods are the prime consideration with flotation as a scavenging process. Greater emphasis on particle size liberation, size reduction and concentration is also indicated. In order to accomplish these objectives, it has been necessary to revert back to the old adage, "Recover your minerals as soon as they are free."

Jan 1, 1980

By Robert E. Moore

Investigators have attempted to develop lime refractories on a scale for broad applications in the metal and ceramic industries for several decades. There was a flurry of activity in the early to mid-fifties but no commercial developments were forthcoming. The literature of that period yields little information on plant trials. A major factor suppressing past interest in lime has to have been the high success with the application of magnesic and dolomitic materials. These materials, usually tar-bonded or impregnated, have become the refractories success story of the past two decades, especially in BOF applications. It is safe to say that their development and application has essentially plateaued, and that work today is focussed on finding cheaper paths to produce MgO-based refractories. For example there are efforts underway to extract MgO from mineral magnesite and to combine natural dolomite with MgO1. Beginning in the late sixties, rather intensive research began on the development of CaO brick, especially in East and West Germany, in Poland, and other communist bloc satellites, 'and also in Italy and Spain. One speculates that the motivation was a regional shortage of good magnesia and dolomitic material. Of course, There has always existed the prospect of cost savings should it be possible to use raw limestone as the starting material. Quite a large literature has appeared treating of these developments which in the early seventies had already reached full plant scale trials and uses. Some of the directions followed in the research have led to novel methods of brick manufacture.

Jan 1, 1985

By Ray E. Williamson

One of the prime objectives of the mine industry is to develop a low cost way to clean up what has been called "The Rape Of Mother Nature". The project falls under the broad umbrella of reclamation, which is now considered an essential part of the mining cycle. As such, it is being given full consideration in the initial planning of all surface operations. In most areas, if a proposed mining system does not lend itself to proper reclamation, it is not an acceptable system. By combining mining and reclamation plans, a producer not only can minimize reclamation costs, but can also restore the land to usefulness and insure continuing profits after a deposit is depleted. As long as fifteen years ago, many of the larger mining companies were already deeply involved in this extra cost work. Even then the involved companies were projecting a great need for a bigger bulldozer, Bigger than anything commercially available. At that time, the D9 tractor weighed about 60,000# bare weight.

Jan 1, 1975

By Thomas S. Nye

Mineral exploration in the United States relies heavily on theoretical geologic concepts and indirect methods such as geophysics and geochemical prospecting, as there are few exposed areas of mineralization which have not already been explored at least once. In Mexico ore-grade samples can be cut at the surface on vein, replacement, and disseminated types of deposits in many areas. Here the problem is not in finding a mineralized area but in deciding which mineralized area can be explored and developed at the least risk and cost, and have the greatest profit potential, within the framework of Mexican mineral economics and government policies. Mexico's min¬eral industry is regulated through a system of permits for various phases of mineral exploitation, and by taxes. This regulation and its effects are not unlike those which may be expected in the United States if present legislative and administrative trends continue.

Jan 1, 1972

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By Michael J. Martinson

Mine ventilation has been evolving as a separate field of study since the middle of the nineteenth century, and some practitioners might assert that mine ventilation has come of age as a discrete field in the last decade or two. Certainly the extensive literature now available on many facets of the subject, international congresses, the phenomenal upsurge of interest in mine ventilation in the United States of America since the passage of the 1969 Federal Coal Mine Health and Safety Act, and the existence of a virile mine ventilation society in South Africa with its own monthly journal all point in this general direction; on the other hand the lack of a rational design philosophy for ventilating mines suggests that mine ventilation may still be on the threshold of maturity. To generalise, many mines are still ventilated simply to comply with arbitrary statutory regulations, or with some ill- defined notion of reducing the risk of injury associated with the atmospheric environment in mines. Hazards in this category include oxygen deficiency, toxic gases and particulates, pathogenic gases and aerosols, explosive gases and dusts, and extreme climatic conditions. Although many mines are ventilated to abate the risk of a specific injury, there is inevitably a spectrum of latent and patent atmospheric hazards in every underground mine. The writer (Martinson, 1976) has previously drawn attention to the dearth of material on mine ventilation design in textbooks and technical journals, and to the overly simplistic approach sometimes adopted in the limited work published on the subject. The available material undoubtedly contains useful technical data and persuasive views, but seemingly could not be used to demonstrate the rational engineering approach to mine ventilation design advocated in the present paper. The range of papers presented at the 1975 and 1979 Congresses, and the diverse interests and affiliations of delegates, emphasize the multidisciplinary nature of mine ventilation. Easily recognisable topics include: Fluid mechanics Thermodynamics Heat transfer Flames and combustion Aerosol physics Radiation physics Geophysics and geomechanics Occupational diseases Epidemiology Industrial physiology Despite these heterogeneous connections there can be little doubt that mine ventilation is fundamentally an engineering field and not an off-shoot of some other branch of applied science. The distinction is important because mine ventilation has essentially developed as a form of ad hoc trouble- shooting, and in the process mining engineers have relied extensively on the assistance of experts drawn from other fields. Thus historically there has been limited scope for the application of rational design techniques, and personnel enlisted from scientific disciplines may not have had any previous experience in the intricacies of engineering design.

Jan 1, 1980

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By David M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been evaluated for: potential use, chiefly as structural clay products, refractories, and lightweight aggregate; lithology; physical properties tests; fired tests, both quick-fire and rotary kiln; major-element chemical analyses, and quantitative five-component X-ray mineralogy for quartz, mica, feldspar, kaolinite, and chlorite-vermiculite-montmoril-lonite. Approximately 80 percent of the samples are of some potential use. Of 220 shale samples, 84 were potential lightweight aggregate sources and 83 potential brick sources. Binary correlations of test data versus potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to super-duty refractories and lightweight aggregate; kaol-finite content for refractories versus low-temperature fired product sources; quartz content illustrating that there is an apparently necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 40 percent minimum for lightweight aggregate; carbon dioxide, which is low for refractorfes, beneficial in lightweight aggregate, and probably restrictive for some tiles choroite yermicalite, which is low for refractoies and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state's major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries, and perhaps a future potential for aluminum from shales that exceed 20 percent A12Q3.

Jan 1, 1971