Search Documents

ShouSteel Mining Ltd., a subsidiary of ShouSteel (Group) Co., was founded in 1959 and is located in QianAn City in Hebei Province, China. ShouSteel?s pelletizing plant uses iron ore as a raw material combined with limestone, dolostone, or olivine, with bentonite as a binder. After mixing the raw materials and forming them into small, spherical balls, ShouSteel then fires pellets in kilns for hardening. The company sells the finished pellets as raw materials for blast furnaces used to produce industrial metals such as iron. ShouSteel?s handling capacity is approximately 24.5 Mt/a (27 million stpy) of ore. The company?s production capacity is 3.2 Mt/a (3.5 million stpy) of oxide pellets and 560 Mt (650 million st) of sinters. Until recently, ShouSteel Mining had not replaced its electronic scales in its series of ingredient chambers. Because of the wear and tear on these older scales, the weighing system began to encounter regular problems. The company experienced a high failure rate from the integrator, an unstable signal, weak anti-interference ability and low accuracy. ShouSteel also found that spare parts required during repairs were consistently high in cost and that system calibration was becoming increasingly frequent.

Jan 1, 2012

By David J. Dunn

Of many physical parameters critical to design of grinding processes, impact of grinding media is among the most difficult to measure or predict. Yet impact of falling grinding balls, pebbles, or rods accomplishes the fine grinding essential to metallurgical recovery of most important minerals. Unfortunately, the same impacts that break ore fragments deform or crack grinding mill liners. A project was undertaken at Climax Molybdenum Company to measure impact forces in operating ball mills so that they might be used to calculate stresses in liner materials and be correlated with service performance of mill liner alloys. Towards that end, a method of measuring impact forces on ball mill liners using an instrumented grinding ball has been developed. Preliminary tests show that impact forces and contact stresses imposed on bare mill liners are quite high but are greatly reduced by cushioning when coarse ore particles are crushed between balls and liners. Compressive and shear stresses induced in liners not protected by coarse ore are so severe that deformation or minute subsurface cracking are inevitable in all but the small production grinding mills, regardless of mill liner alloy strength or hardness.

Jan 1, 1977

By K. Hartman

Certain external forces affect the manner in which business is conducted. and in recent years changes in the business environment have altered how some of these external forces affect the management of a business. These changes must be understood and considered in definition of the strategy of the business. Implementation of the strategy must assure commitment from all departments within a company, and this commitment sometimes involves compromises to assure that a department's goals mesh with the overall business objective such compromises must be externally motivated. i.e. for benefit of the customer. Complete implementation transcends internal departments to all aspects of managing the efforts in the marketplace.

Jan 1, 1989

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. Sunderman

"In underground metal/nonmetal mines, repeated short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently there are no common mechanisms to control or mitigate these localized short-term high exposures to contaminants. To improve miners’ health and safety, the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is developing a Smart Monitoring and Control (SMAC) system for real-time monitoring of mine air quality, with integrated countermeasures to reduce these high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system that could be implemented in an underground mine, researchers at SMRD built a test apparatus incorporating a fan, louver, ducting, and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health. INTRODUCTION Underground metal/nonmetal mines continue to expand production by employing large equipment in greater numbers and by mining into hotter and more challenging environments which are typically further away from fresh air sources. This challenges the ventilation system to provide adequate quantities of fresh air to the workplace and increases the potential for air contamination that could result in immediate and long-term health and safety issues to miners. Currently, airflow and contaminant concentration in mines are typically based on full-shift sampling which may not identify repeated short-term exposures to high levels of airborne contaminants such as NO2, CO, diesel particulate matter (DPM), and dust with high silica contents. Repeated short-term exposure to these high levels of airborne contaminants over long periods can lead to serious health issues which are documented in several studies [1-3]. Based on data from ventilation surveys and contaminant measurements, mines often attempt to minimize exposures by sending more fresh air to the working areas where contaminant concentrations are found to be high. Real-time monitoring and control allows mines the option to monitor contaminants and implement controls in real-time. Real-time monitoring and control of the underground mine atmosphere has been a subject of research since its beginning in Finland at Outokumpu’s Pyhäsalmi Mine in 1969 [4]. More recently, the real-time monitoring and control problem has been addressed using ventilation on demand (VOD) systems [5, 6]. A VOD system attempts to deal with this issue on a global level by controlling fans, louvers, and doors to increase airflow to active work areas and reduce contamination. However, a VOD system only controls the distribution of airflow and may not be helpful in mines where the airflow is at maximum capacity. Researchers at SMRD are developing a SMAC system for real-time monitoring of mine air quality with an integrated ability to trigger countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. The SMAC system will be designed, tested, and refined in the laboratory environment before being demonstrated in an underground mine. This system will not only try to minimize the gaseous contaminants by regulating the airflow locally, but will also potentially employ a filtration system to reduce the airborne contaminants in case the maximum airflow capacity is reached. This paper presents development of the test apparatus for the SMAC system."

Jan 1, 2017

By William E. Robinson

Our earthly treasures are being quickly depleted. We have experienced what can happen in an energy crisis. You have read and heard all kinds of stories as to what caused this crisis. On the surface it would seem that all of a sudden a situation becomes a crisis whether it be fuel, potatoes, beef or whatever. Well, of course, they don't just happen. There is always a little fore-warning here, an indicator there. Someone recognizes a sign of potential trouble but is ridiculed when he forecasts it. We are running out of sand: Producers of aggregates who can say today ... "That couldn't happen to me", can well be awakened tomorrow to the cold fact of reality. It could come from any number of directions. Depletion is mostly foreseeable but zoning isn't. Legislation can also be sudden death to availibility. With the ever growing population moving into the rural countryside, available deposits are being sold either to developers or being zoned for restricted use. The fact that a gravel pit or quarry is located on a particular plot has not fazed some of the local planning boards when they decided to place the adjoining property in a residential Zone A. Proponents of zoning preach that such use is necessary to insure that the land will be put to its best use. Planning boards establish the best places for schools, homes, shopping areas, factories, etc., so that the individuals or groups are in harmony with each other. This is usually done to date without thought or consideration to the geological importance or potential of the area. Today over half of the United States is living under some form of land use restriction. Little consideration has been given to what lies under the ground to be zoned. Fortunately, the states are slowly getting around to geological surveying. I feel that it is about time that state and federal authorities institute governmental restrictions to prohibit or control local zoning ordinances which would deplete or deny an area of its natural resources. While I could continue for the balance of my time just on this facet of our industry's problems, my point is: How sure are you of your next load of sand? I could be well laughed at by some of you for saying that there is an alarmingly rapid disappearance of "nearby" sand and gravel reserves in many areas of the country. A questionable statement, except to those producers where depletion has already taken place.

Jan 1, 1974

By Martin G. Taube, Dwayne A. Lewis

Drainage improvements at O’Hare International Airport, Chicago, IL included the installation of a drainage and storm water system to control the over?ow from nearby Willow Higgins Creek. This involved construction of a weir structure at the creek and the channeling of water from the weir to a newly constructed reservoir via three, 3.7-m(12-ft) diameter, underground storm sewer lines. The sewer lines passed beneath an existing, 2.3-m (90-inch) diameter high-pressure water main, which was to remain in service throughout sewer line installation. The soil composition around the water main ranged from medium stiff clays to silty sands and sandy silts. Triple-fluid jet grouting was used to stabilize the variable soil profile beneath the water main in preparation for tunneling and installation of the sewer lines. The varying soil strata presented a challenge to the project team to establish a constant set of jet grouting parameters throughout the stabilized zone while keeping within the specified unconfined compressive strength range for the stabilized zone of 690 to 1,380 kPa (100 to 200 psi)at 28 days.

Jan 1, 2003

By Art Hamid, Manfred Wong, Carlos Jaramillo, Greg Raines, John Caulfield

"The Central Bayside System Improvement Project (CBSIP) is a critical element of the Sewer System Im-provement Program (SSIP), a 20-year, $6.9-billion investment by the San Francisco Public Utilities Commis-sion (SFPUC) to upgrade San Francisco’s 100+ years old seismically vulnerable combined sewer system. The CBSIP’s centerpiece, a proposed 10,000-foot-long (3,048-meter-long) Channel Tunnel, will provide reliable and redundant gravity conveyance and storage of combined wastewater flows from the northern and central parts of San Francisco to the Southeast Water Pollution Control Plant (SEP) while ensuring compliance with regulatory requirements for combined sewer discharges to the Bay. A tunnel with a diameter of 23 to 30 feet (7 to 9 meter) is being planned using pressurized-face tunnel boring machine technology. Project challenges include tunneling through Franciscan Bedrock, mixed ground conditions in close proximity to the Bay, connector tunnels and shafts, construction in congested urban environment, and challenging real estate issues for shaft access. BACKGROUND AND NEED FOR TUNNEL The City of San Francisco is one of the most beautiful cities in the world. About 850,000 people live in the city and many more come to work, for tourism, and for attending conferences. The SFPUC is a department of the City and County of San Francisco that provides energy, drinking water and wastewater services to San Francisco, wholesale water to three Bay Area counties, and green hydro-electrical and solar power to San Francisco municipal departments. The SFPUC wastewater system includes tunnels, large storage/transport boxes, 1000 miles of collection sewers, 28 pump stations, and three wastewater treatment plants. San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. After decades of service, much of the sewer system is nearing end of its working life. During the 1989 Loma Prieta earthquake, damage to SFPUC water and wastewater infrastructure was extensive. The 11,200-foot-long (3,400-meter-long), 66-inch-diameter (1,676-mm-diameter) Channel Force Main, built in 1976, and a critical component of the SF wastewater system was also damaged. This force main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the SEP. The force main is at the end of its life and was not constructed to the current seismic code; in addition it has no redundancy. Figure 1 shows the project background and the force main that will be provided redundancy by the new gravity tunnel."

Jan 1, 2016

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By Armando Alatorre

The Republic of México is the world's largest producer of celestite/strontium carbonate and natural sodium sulfate. It is also a significant producer of flourspar, barite, graphite, sulfur, feldspar, salt and gypsum. New production may be brought on stream for borates, wollastonite, garnet, calcium carbonate and others. The country covers a geographic area of approximately 2 million square kilometers (760,000 square miles), and is divided into seven geological/geomorphological provinces. Less than 20 percent has been explored in detail for either nonmetallic or metallic minerals. This leaves large areas available for the discovery of world-class industrial mineral deposits. In addition to new deposits of those minerals currently being produced, there is exploration and development potential for borates, magnesite, rare earths, nepheline syenite, heavy mineral sands and numerous others.

Jan 1, 1995

By R. A. Paul

WIDCO, operator of the Centralia Coal Hine, chose dredging, a method not commonly used for overburden removal, as the fastest, safest, and most economical method for mining through an alluvial filled valley. Now that the work has been completed, how did the cost and schedule compare with the original estimates? What would we do different next time in preparing for a dredging contractor? What are the potential pitfalls working with a dredging contractor? Would we do it again? When should dredging be considered as an overburden removal option?

Jan 1, 1989

By Gareth Mainwaring

The Cross Harbor Freight Movement Project is currently in the Environmental Impact Statement phase. The scheme is addressing alternative solutions to transport freight across the Upper Bay of New York Harbor, from New Jersey through to Brooklyn, Queens and Long Island. Amongst the alternatives being assessed are two tunnel options; from the north shore of Staten Island through to Brooklyn, and from Jersey City to Brooklyn. These tunnels are approximately 30,000 feet in length, and with up to17,000 feet under the Harbor, would make it one of the longest undersea crossings in the world.. The paper addresses the development of the project, from the Major Investment Study through to the current EIS, and describes the tunnel schemes that are being taken forward. The geological conditions that will be encountered, proposed construction methods, and the ventilation issues associated with such major undersea tunnels will all be described.

Jan 1, 2003

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By John A. Wolfe

Applications of mathematical statistics to the field of exploration are still relatively new. There are two primary reasons why little has been published in this field. First, if one discovers an effective technique for exploration, he does not like to disclose it. Second, the geologist needs to work closely with a mathematical statistician, and the communications barrier between the disciplines is formidable. The authors of this paper, one a geologist and the other a statistician, were interested in the economic benefit which appeared to be possible in the interdisciplinary area which they have called "geostatistics." An actual example has been selected to illustrate this benefit.

Jan 1, 1962

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

By Samara Ali-Ahmad, Keith Hanks, Cindy Pham

The City of Los Angeles will rehabilitate approximately 9 miles of its North Outfall Sewer. This sewer was constructed in the 1920s as an unreinforced concrete semi-elliptical sewer. One of the methods for rehabilitation is to approach the sewer as a pre-excavated tunnel and install pre-cast segmental liners to provide a single pass corrosion resistant, structurally self sufficient project. The estimated cost for this project is $46 million. The project has completed the pre-design study, and the design is now underway.

Jan 1, 2003

By Phillip R. Moyle

Voluminous deposits of commercial-grade phosphate occur in sedimentary strata in a 350,000 km2 (135,000 mi2) area of the middle Rocky Mountains of North America known as the Western Phosphate Field. The Permian marine strata that host the phosphate were deposited on the western margin of the North American craton and subsequently deformed, first by folding and thrust faulting of the Laramide orogeny, and then by Cenozoic Basin and Range block faulting. Carbonate fluorapatite is the primary phosphorus-bearing mineral. Organic matter is abundant in some strata, and both biogenic and non-biogenic pyrite are also present. Certain strata are enriched in several trace elements, especially in arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), selenium (Se), vanadium (V), uranium (U), and zinc (Zn). Phosphate has been mined from the Western Phosphate Field for nearly 100 years. Phosphate mining and processing constitutes the largest mineral industry of Idaho, producing more than $600 million in processed mineral value in 1997. Resource management agencies, phosphate producers, and others are concerned about the release of Se from phosphate mine wastes, especially at Maybe Canyon, and the potential effects that Se and other trace elements may have on the environment and on human health. U.S. Geological Survey (USGS) Mineral Resources Team scientists initiated a multidisciplinary study of the Permian Phosphoria Formation and related rocks in the south- eastern Idaho sector of the Western Phosphate Field in response to a request by the U.S. Bureau of Land Management (BLM). Studies to date reveal that Se is present in several phases, including native Se, and in an as yet unidentified form, possibly an organo-Se compound. Selenium is also present in pyrite and sphalerite. Selenium concentrations range from 1.2 to greater than 1,000 parts per million (ppm) in samples collected from exposures of the Meade Peak Phosphatic Shale Member of the Phosphoria Formation (Meade Peake) at Enoch Valley. The results suggest that Se concentrations vary spatially across strata and with depth, perhaps comparable to spatial variations of phosphate and organic carbon concentrations throughout the Western Phosphate Field demonstrated in previous studies. Some Se-enriched strata may be of adequate dimension to allow selective extraction during mining. Such units could be handled separately from the main ore process or waste streams and isolated in order to reduce the potential for release of Se to the environment

Jan 1, 2001

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By S. A. Abetel Sabour

In this work, the block theory was applied to determine the safe limit of the angle of face slope at Limestone quarry of Assiut cement company in order to decrease the occurrence of dangerous potential key blocks. Four joint sets were observed and measured at the face. Computer program based on the vector analysis technique was developed to determine the removable block codes. Stereographic projection was also used in this work to determine the removable block codes and to calculate the maximum limit for the angle of dip of the free face, which was found to be 77°.

Jan 1, 1998

By Donald C. Moore

Asamera Minerals Cannan Mine has been producing a 170 g gold/tonne (5 oz gold/ton) siliciaus flotation concentrate since July 1985. Flotation concentrate is shipped to a smelter for gold recovery. Numerous processes have been investigated to economically produce bullion on site. This paper describes the laboratory and pilot plant test results of a bacterial assisted oxidation of the refractory minerals. Economic comparisons with autoclaving and roasting processes are included.

Jan 1, 1989