Search Documents

By Jesse H. Auvil

In January of 1966, during the annual session of Georgia's General Assembly, Representative Paul E. Nessmith of Statesboro, Georgia, walked into my office and asked me what I thought of the advisability and feasibility of a law which would require the mining operators to reclaim their mined out lands. My answer to him was, as a one time mine superintendent and operator, that I probably would not think very highly of the added cost which reclamation would impose on the operation; but that since assuming the job of Chief Geologist and Assistant Director of the Georgia Department of Mines, Mining and Geology, and in retrospect, I could recommend it very highly, particularly in view of the increased pressure being applied by the Federal government along these lines. I stated then and still emphatically state that this sort of administration should be done on the State level rather than the Federal level. He asked me if I would conduct him on a tour through some of the mining country in which I had worked and to this I readily agreed. The result of this trip was that he was adversely impressed by the devastation which the mining operations had wreaked on that area of middle Georgia along the fall line known as the kaolin belt. Very little except talk was done for the remainder of 1966.

Jan 1, 1970

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By J. A. Herbst, Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comminution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5x6.4-m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790:1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By J. Perlacia

Introduction The Bulk Handling Technology has already started its transformation to the Industry 4.0. Having some of the harshest working and environmental conditions of the industry, the possibility of remote analysis and maintenance of the components seems a perfect target to focus on. The most important and expensive tools have been adapted to the digital era during last years, from remotely controlled haul trucks to monitored conveyor belts. However, these big parts of the installations rely in smaller parts that have been left aside for a while, mainly due to the difficulty to adapt them to IoT (Internet of Things). The paradigmatic example is the lack of monitored rollers whereas all the other components of the conveyor belt installations (the belt itself, motors, drums etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stop of the whole conveyor, due to the possible damages to the belt, thus the implementation of an integral monitoring system of all the components of the conveyor is a must. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers, facing all the problems until its final installation in very different demanding conveyors, from the Australian extreme heat to the freezing cold Norway. All the tests done under actual working conditions, in real installations, have given a valuable knowledge in the identification of problems, their solution and the final advantages of a roller monitoring system. Background and Current State The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, an unexpected stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers long or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. As in many other industry products, the condition of rollers can be recognized measuring key parameters like the temperature of the bearings, the vibration level etc. The traditional way is to use the characteristic noise of a failing bearing, but this method usually implies to change several rollers because the maintenance team is not able to identify a single source of the noise. In recent years different attempts to measure the temperature of the bearings have been made, but the result is not accurate enough due to the proximity of the rollers in the idlers

Jan 1, 2019

By John C. Stam

During the past 20 years, the seismic refraction method has been used for depth to bedrock investigations. Its usefulness, however, has been recognized mainly in engineering applications, for instance in connection with the construction of power stations and in dam site investigations etc. Although some knowledge of the depth to bedrock can be of advantage in many other fields, the use of the conventional 12 or 24 channel seismic refraction equipment has been very limited, especially in ore prospecting and mining operations. The reasons for this are mainly the rather complicated operation of the instruments and the high costs. A conventional seismic equipment requires a crew of six men, a highly trained operator and an interpreter. Furthermore, the use of explosives can under certain conditions be undesirable (naighbourhood of houses, damage to agricultural areas etc.). Since 1957 a new one-channel seismograph, 'constructed by Geophysical Specialties Company, Minneapolis, Minnesota, has been in use and this instrument simplifies operations and reduces their costs considerably.

Jan 1, 1959

By John Fred Rivera

Since its inception during the hectic days of World War II, Kaiser Steel Corporation has developed and maintained a solid reputation as a progressive company with an incessant penchant for attempting innovative ideas to improve its stature in the American and world corporate framework. The very latest in technology is aptly demonstrated in the new Basic Oxygen Process recently placed into operation at Kaiser's huge Fontana Steel Mill. Daring ventures such as this and other developments on pollution control devices have propelled Kaiser Steel Corporation into the forefront as the largest steel producer in the western United States. Kaiser Steel's boldness and willingness to attempt new ideas and the very latest in technology is by no means limited to its steelmaking operation. It extends into every phase of Kaiser's corporate structure.

Jan 1, 1979

By Qingming Feng, Jinhong Zhang

This study investigates the application of fly ash as a high-strength, water-resistant precast construction material through geopolymerization. The experimental results show that working conditions such as water content, sodium hydroxide (NaOH) concentration, curing temperature and curing time significantly affect the mechanical properties of the geopolymer matrix. Through optimization, compressive strength above 100 MPa was achieved, and the optimum working conditions were found to be NaOH concentration of 10 M, water content of approximately 14 to 15 percent, and curing at 90 °C in an oven for one day or at ambient condition for three weeks. Water-soaking tests show that the geopolymerization product has high water resistance without losing noticeable compressive strength even after one month of soaking time. The findings provide a novel method to apply fly ash as a high-strength, water-resistant precast construction material.

By J. R. Pennington

The town of Green River, Wyoming, is located along the Green River on an arid plateau at a elevation of 6,300 feet. Green River has become the center of a booming soda ash industry. The rapid development of coal, oil, and gas resources, coupled with the soda ash boom, have created growth pains for the area. Green River and Rock Springs have experienced a 20-25% population increase in 1973 alone. However, public officials, business leaders, and local citizens are taking positive steps to ease the problems relating to housing, schools, medical services, and recreational facilities. What Is Soda Ash? Soda ash is one of the most widely used chemicals in the world. It is an important raw material in the manufacture of glass, paper, soap, petroleum products, metals, chemicals, pharmaceuticals, plastics, and a host of other items essential to every day living. In ancient times, soda ash was obtained from water solutions of various desert earths. Later, it was produced by leaching the ashes of wood and seaweed. For the past 100 years, it has been manufactured by the ammonia-soda process, which employs large quantities of salt, limestone, and coal as raw materials.

Jan 1, 1974

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By R. J. Haydel

The Highland Uranium Operations of Exxon Company, U.S.A. is a large uranium mining and processing complex situated in the Powder River Basin of East-central Wyoming. Surface mining and chemical processing of a large relatively low-grade ore body began in late 1972. An underground mine was later developed and began production in November of 1977. Figure 1 shows the location of our operations. During the planning stages of the project, it was recognized that hiring and retaining quality employees would be a significant problem. Other operations in similarly isolated locations were experiencing high turnover rates and were forced to employ inexperienced and poorly trained operators. In an attempt to attract employees, many of the companies provided mobile home or bunk- house facilities, but these costly peripheral ventures did not prove to be noticeably successful.

Jan 1, 1979

By T. Mudder

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By R. E. Brewer

Phelps Dodge Mining Company (Phelps Dodge) is operating a pressure leach vessel (PLV) for copper concentrates at the Bagdad Mine facility in Arizona. This single PLV unit was engineered and constructed based on continuous laboratory testing, reaction chemistry and kinetics, and available pressure vessel technology. The challenge of designing for optimum process retention time, agitation, oxygen mass transfer, temperature and pressure will be reviewed in this paper. The PLV interior lining, agitation equipment and compartment configuration chosen for the PLV will also be reviewed.

Jan 1, 2004

By G. Triantafillou

The aim of this paper is to present the progress of the plan of the Greek Public Power Corporation S.A. (PPC S.A.) at the Lignite Centre of Megalopolis in Peloponnesus (southern Greece) to manage impacts on local communities in areas affected by its activities during the lignite mining operation and post-closure. The reclamation works in the waste dump areas of the mines that constitute the Megalopolis Lignite Centre, concerning the utilization of waste dumps for infrastructure community projects constructions are discussed. Moreover, selected environmental indicators concerning land use and closure and rehabilitation are presented.

Jan 1, 2008

By R. J. McGregor, Deepak Malhotra

Engineers frequently encounter situations where decisions that are counterintuitive to the logically trained engineering mind are made because of other influences, whether they be financial, social, cultural, or environmental. Such influences can overrule the "logical" decision-making process. The aim of this book is to explore some of the nontechnical issues, which most engineers don't learn about in school, that can have a major impact in the mining industry. This chapter gives a brief overview of this volume and introduces the topics that will be addressed.

Jan 1, 2001

By Marietta Canty

Results are presented that were gathered during field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE Technology Applications, Inc., located in Butte, Montana. A field-scale test is described in which the subsurface workings of an abandoned mine were used as an "in situ biological reactor."

Jan 1, 2000

By M. S. Duffy

To exploit the mineral resources of fine grained ore bodies the minerals processing industry is turning to fine grinding technology, of which tower milling has become an established part. However, compared to other mills relatively little is known about the operating mechanisms in tower mills. In all milling processes one of the keys to understanding how they work is in knowing how their grinding media move. To investigate the ball motion in tower mills a glass unit was therefore constructed and measurements taken of the movement of the grinding media. This paper describes the results from this study.

Jan 1, 1998

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By Kerry J. Stanaway, Thomas E. Garnar

Titanium was discovered in 1791 and, four years later, was named after the Titans of Greek mythology. Titanium metal was first made in 1910, but was not used commercially until the 1950s when it was nick-named The Wonder Metal of the Age. The first titanium dioxide (TiO2) white pigments were produced commercially in 1915; more than 90% of the titanium minerals produced in the world today are used in the manufacture of white pigments. The remaining 10% are used to manufacture titanium metal and other uses such as welding rod fluxes. Titanium mineral mining began in the United States between 1880 and 1900 in Chester County, Pennyslvania. Rutile from a deposit near Roseland, VA, was mined in 1901. The use for the rutile was limited to production of a few titanium chemicals and for coloring ceramics. Larger scale mining for ilmenite, rutile, and zircon began in Florida to provide chemical materials for use in World War I in 1918. This mining ended in 1928. Large scale mining of titanium minerals in Australia began when Benick, Anderson, and Porter (later called Tamco) started mining the beach sands at Yamba in New South Wales in 1935. Ilmenite production from beach sands in the State of Kerala in southwestern India also began in the 1930s. The 1940s saw many changes in titanium mineral mining. Extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec. The Pigments Department of E.I. Du Pont de Nemours & Co. lost their high grade Indian ilmenite supply after World War II began, and they were forced to use lower grade ilmenite from National Lead's (now NL Industries) Sanford Lake Deposit, near Tahawus, NY, in the Adirondack Mountains. At the end of the war, Du Pont undertook an intense search for a domestic ilmenite source. With the cooperation of the US Bureau of Mines, Du Pont geologists found a very large deposit east of Starke, FL, in 1946. In 1948 Du Pont entered into a contract with Humphreys Gold Corp., who operated a heavy minerals mine near Jacksonville, FL, to construct a plant and operate it for a period of ten years. The plant started up in 1949 and operated under Humphreys' management until the contract expired in 1958. Du Pont has operated the plant since that time. In 1956, a second plant was designed and built by Du Pont a few kilometers northeast of the town of Lawtey. The 1960s saw titanium mineral production expand in the southeastern US with Humphreys' contract mining Du Pont's ore body at Folkston, GA. In the early 1970s. American Cyanamid and Union Camp Paper Co. formed a joint venture company, Titanium Enterprises (TE), to mine and separate titanium minerals from Union Camp's ore deposit southwest of Green Cove Springs, FL. In 1975 the TE plant was shutdown and later sold to Associated Minerals (USA), Inc. (AMC), a subsidiary of Renison Goldfields Consolidated Ltd., an Australian company. It now operates under the name RGC (USA). Mineral production grew in the 1970s with the development of extensive heavy mineral deposits at Eneabba in Western Australia and Richards Bay in the Republic of South Africa. The 1980s saw the construction of a very large ilmenite mine and synthetic rutile processing plant in the state of Orissa southwest of Calcutta, India. At the same time, concern for titanium mineral shortages expected by the end of this century, gave rise to a flurry of exploration activity during the mid 1980s. As a result, large deposits were found in Virginia and North Carolina. New deposits were also discovered in Australia. Fig. 1 shows the distribution of world titanium deposits and mines. The world TiO, production capacities are given in Table 1.

Jan 1, 1994

By Carl R. Christiansen

Excellent underground industrial sites and warehouse facilities have been constructed in Europe and at several locations in the United States. Many quarry and mine operators are considering, or should consider, the possibilities of the development of their mineral properties in such a manner as to make underground space that is suitable for a secondary industrial use. Before proceeding with mine or quarry development, the operator should answer the following questions: 1) Is there a need for underground industrial space in your geographical area? 2) Is your deposit suitable for development of space for industrial usage? 3) If the deposit is suitable, what methods of development can be used? 4) What are the comparative economics of the different methods of space development? An honest analysis of the first two questions may eliminate the need for proceeding to the third. Affirmative answers to questions 1 and 2 should be followed by the engineering and economic studies required in response to questions 3 and 4.

Jan 1, 1975