Search Documents

By O. A. Bascur

Based on current sedimentation theory an on-line thickener model was developed and coupled with an extended Kalman Filter to obtain additional information such as the compression zone level and concentration, a corrected underflow concentration, the inventory, and some rheological information. The on-line model was installed and tested for robustness for periods up to three days in an industrial environment giving good results. Emphasis was given to signal processing and selecting the appropriate input variables for filtering. The analysis of the thickener from a phenomenlogical point of view provides for better operation, establishes the limiting operating conditions, and assists in the design of control strategies.

Jan 1, 1986

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By Daniel A. Servigna, Pedro V. Porcayo, Humberto F. Preciado

This case study presents successful conversions of two conventional slurry tailings storage facilities (TSFs) to filtered tailings storage facilities in Durango, Mexico, for two mining operations with production rates ranging from 1,200 to 4,500 t/d (1,320 to 4,960 stpd). In both cases, the decision to make the conversion was driven by: • Ability to increase the storage capacity via stacking of filtered tailings. • Reduction of the tailings’ impacted footprint. • Mitigation of long-term geotechnical stability risks. • Alleviation of environmental risks by reducing tailings water as a source of pollutants, and a net reduction in process make-up water demand. The case studies can be divided in two classes: class 1 facilities, where slurry tailings are loaded almost immediately with filtered tailings because of storage area limitations; and class 2 facilities, where the conversion is immediate but the available area allows gradual or eventual loading of the previously stored slurry tailings. The condition where slurry tailings must be loaded almost immediately represents the greatest engineering challenge because of the geotechnical risks of instability and liquefaction (under both static and dynamic loads). Regardless of whether these facilities are converted immediately or eventually, they all require monitoring of pore water pressure conditions within the slurry tailings being loaded as the depth of placement of the filtered tailings above the slurry tailings increases. Additionally, where loading rate exceeds the pore pressure dissipation rate, tailings dewatering may be required to increase the rate of consolidation and strength and mitigate the risks of foundation failure.

Jul 1, 2025

By Clarence Hardy Long

In January of 1969 the United States Department of Health, Education and Welfare, through the National Air Pollution Control Administration, published a series of Air Quality Criteria (4'S) and Control Techniques (6,7) for air pollutants in compliance with the 1967 Clean Air Act which will affect the operation of all fuel burning equipment in the very near future. The design of equipment for the future which will use fossil fuels will also be affected. The purpose of this paper is to discuss some of the modifications which might be anticipated in the future for fuel burning equipment. One class of the several air pollutants looked at first by the USDHEW was the sulfur oxides. Other pollutants, such as nitrogen oxides, will be studied and controls for these will supposedly be written in due time. The obvious use of low-sulfur fuels, coal, oil and natural gas is suggested by the Control Technique(6). Conversion to other sources of power, such as nuclear energy and hydropower, is also suggested. The statement is made that since possible hydroelectric sources are limited and nuclear plants are not yet available on a large scale, the changeover to these sources of power will not be overnight. The bulletin (6) suggests that one possible solution in some areas may be the use of low sulfur coals for short periods of time during periods of severe air pollution. A curve showing the effect of this was given in the 1969 April issue of the Power magazine, where A. E. Boyer and F. B. Kaylor of Stone and Webster also described a computer program called DOSAGE which might be used to check weather, temperature, humidity, wind direction and velocity, and sound an alarm when that 0.1% of the time per season is here that requires the use of low-sulfur fuel. Inversion is eminent! Once this has passed operation on regular fuel may be resumed. This would mean a separate storage

Jan 1, 1970

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By Nelson R. Shaffer

Biotechnology has become a household word of the nineties, and it is expected to become as important in the next century as the computer is in the present. Numerous books and articles portray biotechnology developments as nothing less than a scientific revolution. Almost everywhere one looks new biotechnical breakthroughs are being reported that offer almost limitless opportunities to harness the force of living things to produce materials and manipulate their properties. Biotechnology has been broadly defined as any applications of biological organisms, systems, or processes to manufacturing and service industries. This seemingly new technology is, in fact, one of mankind's oldest scientific activities (Table l), which has been recently revolutionized by techniques of genetic engineering that arose out of basic research in biology, biochemistry, genetics, and information sciences. From fields as old as agriculture and medicine to those as new as monoclonal anti-bodies, transgenic plants, or biocomputers are encompassed by biotechnology. Like most human endeavors, industrial minerals play critical roles in biotechnology. In addition biotechnology holds real potential to improve extraction and beneficiation of certain industrial minerals themselves. BIOTECHNOLOGY OVERVIEW Companies using established biotechnical techniques make up large and diverse groups such as agriculture, chemicals, and pharmaceuticals. The massive US Pharmacopia (Anon., 1990a) provides detailed specifications for minerals used in medicines. Alumina, zirconia, apatite, and bioactive glass have seen service as implant materials (Williams, 1990) and new uses for minerals in health sciences are being actively researched. Agriculture produced $361 billion worth of food and drink during 1991 in the United States; organic chemicals, pharmaceuticals, and enzymes accounted for $68, $59, and $42 billion, respectively (Anon., 1992a). It is not possible to separate the contributions of industrial minerals to biotechnical products, but they represent a very large and rapidly growing new field of uses. The new biotechnology has nearly 300 small companies, plus 15 established companies with 742 biotechnology-related firms (Dibner, 1991b). Revenues exceeded $2 billion in 1990 and are expected to grow to $50 billion by 2000 (Anon., 1992c), with worldwide sales exceeding $100 billion (Burrill and Roberts, 1992). Federal research amounted to $3.4 billion in 1990 (Anon., 1992b). The United States is the world leader in biotechnology, but other countries have large, well-funded programs. Despite debate about safety, obstacles to new biotechnology products are declining (Embers, 1992, Gibbons, 1991). Fifteen biotechnology drugs valued at $1.2 billion (Thayer, 1991a) are on the market, and more than 100 are in various stages of testing (Edington, 1992). Many diagnostic tests are also in use or development (Demain, 1983, Anon., 1992). Large scale efforts to produce or transform important chemicals are also underway (Ng et al., 1983, Hinman, 1991), and research into geologic uses of biotechnology has begun. Much has been published about microbial mining, oil recovery, desulfurization, bioremediation, and other geologic aspects of biotechnology, but this chapter is the first attempt to explore interactions of biotechnology and industrial minerals. This chapter examines uses of minerals in biotechnology; how biotechnology can be used to discover, recover, and beneficiate industrial minerals; and speculates on some potential, but as yet untried uses. Definitions What exactly does the word biotechnology mean? Bud (1989) states that the first use of the term was by Karl Ereky in 1919 to cover the interaction of biology and technology, and in 1933 the term was used in Nature. After citing seven different definitions, Smith (1988) concludes that biotechnology is a series of enabling technologies involving practical applications of organisms or their subcellular components to manufacturing and service industries or to environmental management. Walker and Cox (1988) suggest a definition of "the practical applications of biological systems to the manufacturing and service industries and to the management of the environment." Primrose (1991) says that it is "the commercial exploitation of living organisms or their components." There is essentially an older broad use of the term and a new use. The US Office of Technology Assessment (Anon., 1984) uses a broad definition that includes any technique that uses living organisms (or parts of organisms) to make or modify products, to improve plants or animals, or to develop micro-organisms for specific uses. Definitions are different, but they all have several fundamental elements that include the control, management, or manipulation of living things for commercial, industrial, or useful ends. While such a definition encompasses all of agriculture in practice the "new" biotechnology is restricted to processes involving microorganisms-plant and animal cells, or enzymes. Many consider biotechnology to be recent, but it is one of our oldest technologies as evidenced by the prehistoric origin of brewing, cheese-making, and other techniques. [Table 1] gives some of the important developments in the history of biotechnology. Smith (1988) breaks down historical developments of biotechnology into four phases: 1) prehistoric with no understanding of underlying processes; 2) nonsterile processes; 3) sterile processes after 1940; and 4) genetic and recombinant DNA technology deliberate design of special organisms or processes.

Jan 1, 1994

By David M. Shaw, John C. Franklin

A 32-channel warning system for high working level, fan operation, and airlock-doors has been constructed. The working level monitors have a microcomputer for accumulating the pulses, converting to working level, and triggering an alarm at a variable set point and at one working level. The system also detects when underground fans lose power or air doors are open. The system can detect changes in air velocity which indicate surface fan failures or changes in the ventilation system. Using this alarm system, the ventilation engineer will be alerted prior to excessive levels of radon daughters being reached so corrective action can be taken.

Jan 1, 1981

By John F. MacDonald, John W. Critchfield

This paper describes the shield excavation of twin transit tunnels, through soft ground, in downtown Seattle. The tunnels are 6.5 m (21.25 ft) diameter and 1525 m (5000 ft) long. Initial support consisted of expandable precast concrete segments, followed by a final lining of cast-in-place concrete. Waterproofing was provided by a PVC membrane installed between the initial support and the final lining. During the course of the excavation a variety of methods were used to control the ground and limit settlement. These included deep wells, vacuum well points, eductor wells, chemical grouting, compaction grouting, jet-grout underpinning, and extensive instrumentation.

Jan 1, 1989

By Jon Kellar, William Cross, Eric Swanson, John Starkovich

Zirconium tungstate (ZrW2O8) is a unique material with a negative coefficient of thermal expansion. In order to fully utilize this material as a filler, a surface treatment needs to be developed to better improve the wetting and dispersion capabilities of the filler. This paper describes an initial study to characterize the filler as well as investigate fatty acid and silane surface treatments for eventual compounding with thermosetting matrices. It was found that ZrW20, has a point-of- zero charge between pH 2.7-3.0, and that both fatty acid and organofunctional silane treatments appear to be viable surface treatments for this unique filler.

Jan 1, 2003

By J. Engel

The talc deposit in Gemerská Poloma lies 350 to 400 m under the surface; the whole deposit is located at the highest-level drinking-water-source protection zone, therefore, opening in this mining area (a well, a ramp) requires higher investment, operational and water protection costs. The adit, outside the mining area, with a length of 4200 m, rising with a gradient of 3? and a diameter of 10.3 m2, allows free passage/runoff of mining-water through the adit, and guarantees low costs for transporting produced material and equipment. This solution is in total less demanding from both investment and operational point of view.

Jan 1, 2007

By A. P. Chaves, A. Gomes

The cyanidation and adsorption processes at Fazenda Brasileiro mine were studied with the aim of increasing hydrometallurgical recovery. Technical evaluation of the processes consisted of (i) quantitative mineralogy of ore samples collected in different points of the circuit, and (ii) comparison of plant performance in the original (designed CIP) and in the modified (current CIP/CIL) circuits. An empirical correlation between process variables and gold grades in the cyanidation tailings was established. The suggested modifications in the circuit and in the operation conditions led to an increase in gold recovery, from 91 to 93.5%. Annual revenue is expected to show an increase of approximately US$ 1 million.

Jan 1, 1998

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By J. Herbst, H. W. Kropholler, L. A. Cramer, E. T. Woodburn, J. C. A. Greene, G. Poling

A generalized mathematical structure is proposed whereby internal species mass flows within a flotation network are defined uniquely by a matrix of enhancement factors. An element of the enhancement factor matrix is defined as the ratio of the mass flow of that species leaving a given cell in the concentrate to the species mass flow leaving the same cell in the tailings. To predict the enhancement factors, knowledge of flotation kinetics effects is required. Recently experimental data has become available relating to the performance of industrial flotation circuits which indicate that the discrete or discrete-distributed kinetic schemes are capable of reasonably effective simulations. These simulations show the importance of including froth effects. The prediction of performance of networks from small-scale batch tests on flotation streams shows that the model for the froth phase used in the simulations does not scale-up well and that aeration effects are also difficult to predict. The network analysis should be useful in differential flotation of complex ores and it is disappointing in this context that little information on the kinetics of activation and depression is available.

Jan 1, 1976

By J. A. Cervantes

A statistical model for assessing the risk of ground subsidence in abandoned mine areas is presented. The model is based on the relationship that exists between .the frequency and the location-of subsidence events in a given area and the physical conditions of the ground. These conditions can be described by a series of geological, mining, and physical variables. The model suggests the existence of regions in the multidimensional space of variables which are associated .with increases or decreases in the frequency of subsidence events. Regions associated with an increase in the frequency of subsidence events correspond to regions of higher risks, and vice versa. Risk assessment is based on the ability to express the limits of these high and low risk regions in the, space of variables, and on the ability to express the degree of membership of blocks of land within any of these regions. The theoretical framework for the model is extracted, from discriminant analysis. Risk is quantified by the probabilities of membership of blocks of land into any of these regions. Risk maps are produced by displaying membership probabilities in. appropriate contouring levels. The model has been applied in two urban areas where subsidence of the ground has been active in the past. The two areas are Penn Hills, near Pittsburgh, and Scranton/Wilkes-Barre in northeastern Pennsylvania. In this paper, only the results for the Scranton/Wilkes-Barre area are presented. Those for the Penn Hills area have been presented elsewhere (Cervantes, et al, 1990). In the- Scranton/Wilkes-Barre area, geostatistical estimates of variables likely to affect the stability of the ground were made using samples from 53 drillholes. The estimates were made for 2000x2000 ft squared blocks of land covering the study area. Discriminant functions were computed from the estimated variables and used to establish regions for classifying blocks of land into one of these two populations: 1) blocks not likely to have a subsidence event, and ii) blocks likely to have one or more subsidence events. The same, discriminant functions were used to compute membership probabilities for blocks of land to tall within any of these two populations. These probabilities were contoured to produce a risk map. The risk map produced compares well with the location of the subsidence events which have occurred to date in the area.

Jan 1, 1992

By D. M. S. Bhatia

Twenty-six insitu analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an increase in the concentrations of Ag, Ga, Ge, and In with As showing the opposite trend Bi, Cd and Sn did not show any pattern. Sb was not detected. These variation patterns nay serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1984

By Daniel C. McLean

Chemistry plays a more important role in milling operations than is generally recognized, particularly in fluid- solid separation processes. Chemical aspects are also very important insofar as plant water quality is concerned, and in the manner in which this water quality effects plant design and operation. Aside from the inherent chemical characteristics of plant water, the mineral preparation industry is becoming increasingly more dependent on the use of mining chemical reagents--relatively new to the coal industry, but items of I standard usage in complex metal recovery plants. These chemicals have many useful properties and can produce significant improvements in operations and metallurgical efficiencies when used properly and intelligently. They can produce poor results and sometimes severe losses when used improperly. Most reagents are relatively expensive on a per pound basis, hence costs can be excessive if they are used wastefully or inefficiently.

Jan 1, 1968

By R. David Williams

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management (BLM), U.S. Forest Service (USFS) and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the U.S. Forest Service and Bureau of Land Management. The Bureau of Land Management has worked with the State of Montana and other agencies to identify and prioritize these sites on BLM administered lands. Following completion of the AML inventory work, the Bureau began an aggressive program to clean up priority sites. This presentation will highlight completed work as well as work in progress on several sites.

Jan 1, 2000

By G. L. Myers

The Fortitude skarn near Battle Mountain, NV is currently one of the largest producing gold skarns in the world. It contains about 11 Mt (12 million st) of minable ore grading 5.14 g/t (0.149 oz per st) and is the distal portion of a continuous skarn system in the Copper Canyon area centered on the Eocene Copper Canyon granodiorite porphyry. Calcsilicate compositions, opaque mineralogy, and the high gold grades are atypical of other base metal skarns (iron, Fe; copper, Cu; lead-zinc, Pb-Zn; or tungsten, W). The Copper Canyon skarn is systematically zoned from a garnet (AD 70-100) dominant, pyroxene (HD 20-45) subordinate zone, with major Cu mineralization, adjacent to the intrusive (West ore body), to a pyroxene (HD20-100) dominant, garnet (AD90-100 cores. AD 30-60 rims)subordinate assemblage, with major Au, near the distal marble front (Fortitude ore body). An extensive biotite ± diopsidic pyroxene ± kspar alteration halo surrounds the pyroxene > garnet gold-bearing skarn and represents the early stages of metasomatic alteration. Retrograde alteration is limited in areal extent and intensity, and consists of actinolite, chlorite, quartz, and prehnite. Economic gold mineralization begins in the pyroxene > garnet zone and continues to the marble front, a distance of 1 to 1.5 km (0.6 to 0.9 miles), respectively, from the plutonic contact. The opaque mineralogy in this gold zone includes pyrrhotite, arsenopyrite, marcasite, minor chalcopyrite, galena, sphalerite, argentite, hessite, hedleyite, volnyskite, and native bismuth and gold. The pyrite-pyrrhotite geothermometer yields temperatures that range from 450° C to 300°C (842° F to 582° F) and the electrum-argentite-sphalerite geothermometer yields temperatures which range from 290°C (554° F) at the marble front to about 420°C (788° F) more proximal to the intrusive. Log fS2 calculations from the sulfide assemblages yield values near - 10 with log fO2 values of about -30, in a solution of near neutral pH (5-6). Calculations of metal solubility suggest that the metals were transported as chloride complexes in the proximal skarn but that bisulfide complexes were predominant within the distal gold skarn. Relatively low oxidation states buffered by the carbonaceous to argilliceous, calcareous protolith and subsequent ferrous iron-rich skarn assemblages appear to have increased the gold carrying capacity of this large hydrothermal system.

Jan 1, 1991