Search Documents

The concept of classification in wet, closed circuit ball milling is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters that effect fines removal are identified and discussed, and a quantitative index for circuit classification effectiveness is presented.

Jan 1, 1987

By Angus Campbell, Michael J. Gobla

Numerous techniques for treating, controlling, and preventing acid rock drainage have been applied at the Summitville Mine Superfund Site. Challenging aspects of the remote mine site include the wide-spread occurrence of acid-generating soils and rocks, extensive surface and underground mine workings, and a cold and wet climate. Water treatment was an immediate necessity when the Government took control of the abandoned site in December of 1992. Subsequent reclamation activities have emphasized prevention and control of ARD to minimize future water treatment requirements. A combination of conventional, innovative, and experimental methods are being applied to successfully mitigate ARD at Summitville.

Jan 1, 2000

By C. H. Rawlins

The total amount of ferrous slag generated in the U.S. is about one-third the amount of iron ore mined, thus ferrous slag can be considered a significant mineral body for processing. Steelmaking slag contains up to 30 wt.% metal of which only the >25mm fraction is commonly recovered. A grinding study was conducted of BOF, EAF, and LMF slags using the Bond Work Index method to determine grindability to 106µm. Work Index values obtained were 13.8-24.9 kWh/ST, depending upon the slag type and composition. Steel particles were magnetically recovered from the crushed and ground samples for size-by-size analysis, yielding up to 18 wt.% of the slag weight recovered as magnetic. The recovered material, as characterized by inert gas melting, was found to be 61-96 wt.% metallic.

Jan 1, 2008

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the US Department of Energy. The repository is located at a depth of 655 min the Permian age salt beds of the Salado Formation. The exhaust air from the facility is independently monitored by the Environmental Evaluation Group to verify compliance with regulatory release limits for radioactive materials. A May 1995 video inspection of the exhaust shaft identified fluid migration into the uppermost 25 m of the shaft. Since then, water has been observed flowing in from cracks in the shaft lining between 16and 25 m below surface level at an estimated rate of between 5 and15 m3/d. This water inflow has not only negatively impacted the equipment in the shaft, associated duct-work and monitoring equipment located at the top of the shaft, but also challenged efforts to verify compliance at the WIPP. This paper provides an analysis of these effects.

Jan 1, 2004

By G. T. Adel, J. D. Miller, C. L. Lin

In view of the success of recent laboratory studies using X-ray computed tomography (CT) to determine coal washability and with the availability of high-speed CT systems, it now seems possible to design an on-stream washability system for the control of coarse coal-cleaning circuits. Design features for such a system are examined and possible control strategies are discussed for different applications.

Jan 1, 1995

By Clayton J. Parr, Northcutt Ely

Mining law is essentially a branch of the law of real property. It concerns acquisition of property for extracting contained minerals, and the rights, privileges and duties that fall upon the holder thereof once the rights are acquired Accordingly, this section focuses on the procedures to be followed in acquiring state. federal and private lands, and defines briefly the nature of the rights obtained. The mining laws of Canada and Mexico are summarized, and the related subjects of minerals taxation and governmental regulation are discussed briefly. This section is not intended to be the basis for legal decisions. Rather, its purpose is to provide the engineer with an understanding of basic principles and procedures. For a detailed treatise of mining law, reference can be made to The American Law o] Mining, a five-volume set edited by the Rocky Mountain Mineral Law Foundation. The law changes constantly, especially that based on federal and state statutes, and the reader is cautioned to be alert for subsequent modifications of statutes, regulations and case law. 2.1-PRELIMINARY LAND-STATUS CHECK Often, after completion of area reconnaissance, or perhaps after receipt of a submittal, a specific more localized target area will become of interest. Usually, an intensive exploration program comprising detailed surface mapping, sampling, geophysical prospecting and drilling will be required before the mineral potential of the ground can be properly evaluated. Before an investment of this magnitude is made, however, it is advisable to obtain rights to mine ore from the property. Otherwise, knowledge of the exploration activity might greatly inflate land values, or speculators or competing mining concerns might step in. Hence, as a general rule, a land-acquisition program should be undertaken before an intensive exploration project is begun. The first step in such a program is to make a land-status check to determine whether the subject lands are available and, if so, from whom they can be obtained and by what means. 2.1.1-BUREAU OF LAND MANAGEMENT RECORDS In those states which contain large areas of federal land, basically (he western states, the primary informational source is the records of the Bureau of Land Management. These may t)e examined at the land office having jurisdiction over federal lands in the area of interest. The records for Montana and North and South Dakota are kept at the Billings (Mont ) land office; Wyoming, Nebraska and Kansas, Cliejenne, Wyo.; New Mexico, Oklahoma and Texas, Santa Fe, N M ; northern Alaska, Fairbanks, and southern, Anchorage; Utah, Salt Lake City; Nevada, Reno; Arizona, Phoenix; Colorado, Denver. There are two land offices in California, at Sacramento and Los Angeles Records for other states are kept in Washington, D C. at the office of the Director, Bureau of Land Management.

Jan 1, 1973

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By John A. Cordes, John J. Schanz

INTRODUCTION The economic structures of industrialized countries require a continuous supply of reasonably priced and appropriately processed nonfuel minerals. As a result, national policy makers are sensitive to real or perceived threats to the effective operation of these commodity markets. Their most persistent concerns can be subsumed into the related political economy issues of supply availability and marketplace stability. These concerns are not new. For over a century the "global struggle" for mineral resources has influenced national policies and international relations (Eckes, 1979). During the past two decades the complexity of these issues, if not their place on national political agendas, has increased. Dramatic changes in the structure of mineral industries and in the nature of international economic relations have redefined policy needs and response options. This paper focuses on how selected OECD countries have responded to nonfuel mineral industry issues over the past twenty-five years. Particular emphasis is placed on the impact these policy decisions have had on the size and location of productive capacity and its utilization rates. The results, perhaps, are not surprising for this group of market- oriented economics. While individual cases of significant impact are easy to identify at various times in most countries, the overall importance of policy decisions has not been great. This is especially true for the past decade when excess capacity reached unusual highs of magnitude and duration. Macroeconomic forces and market structure changes played much more important roles. PERSPECTIVES ON THE ISSUES OECD nations dominate the international nonfuel minerals marketplace as producers, consumers and traders. In 1986, these twenty-four countries accounted for 75 percent of the Western world's export trade value in minerals, ores and metals. They imported 88 percent of the total value. During 1966, the respective percentages were 70 and 94. Japan was the world's largest importer in 1986 followed by the US, FRG, UK and France. The same five countries led the 1966 list except that, then, Japan was ranked fourth. Table 1 ranks the fifteen largest Western exporting nations in the two specified years. It also indicates the growth in current export dollars earned in 1986 compared to 1966.

Jan 1, 1989

By J. H. Hill

The globalization of mineral markets and intense competition in downstream mineral-consuming industries such as transportation, agriculture, and construction are requiring raw materials suppliers to innovate, improve quality, invest in new technology, and control costs. Mineral specifications are becoming more refined, and pressure to improve products is felt from increasing numbers of competing producers, substitute materials, customers, and regulators. As a result, engineered mineral products are becoming more like manufactured ones in terms of cost structure, differentiation, and the importance of market driven, customer specific product development. Engineered mineral products are defined as those where the costs of refining and upgrading outweigh those of conventional mining activities (blasting, crushing, classification, haulage etc.), and where close control of physical and chemical parameters is required for customers' processing and manufacturing applications. This includes industrial minerals such as calcium carbonate, kaolin, mica, specialty oxides, talc, and some metal powders. It excludes most metals and bulk commodity materials such as gypsum, lime, sulfur, and soda ash. Engineered mineral products are utilized in common household goods, and are at the forefront of industrial materials engineering in plastics, ceramics, composites, glazes, coatings, and construction materials. As a group, they introduce interesting questions to the minerals firm. Advanced materials or basic? Diversify or specialize? What are the implications of advanced materials and for mineral markets, and most importantly, where can the producer look for long-term value, volume, and profits?

Jan 1, 1993

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By Jamal Rostami, Alireza Salimi, Christian Moormann

"Rock mass classification systems are often applied in many empirical design practices in rock engineering, some contrasting with the original intent and applications of these classification systems, for example, estimation of TBM performance in various ground conditions. While accurate estimation of machine performance is significantly impacted by rock mass properties, parameters used in many of the existing classifications are more related to ground support design and not rock mass boreablity. The results of many investigations on this issue have shown a weak correlation between TBM rate of penetration and rock mass classification. This limitation can be overcome by fine tuning the rock mass classification input parameters to represent influence of rock mass properties on TBM performance as has been the objective of RME or QTBM. This paper will offer an overview of the impact of rock mass on TBM performance and introduces an empirical equation for predicting performance of rock TBMs based on rock mass classification. The results of the preliminary analysis of a new model has revealed that the use of the proposed system can offer a reasonable accuracy for estimation of TBM performance in various rock masses. 1. INTRODUCTION Hard rock tunnel boring has become more or less the standard method of tunneling for tunnels of various sizes with lengths over 1.5–2 km. Estimating the performance of TBM is a vital phase in tunnel design, and for the choice of the most appropriate excavation machine. During the past three decades, numerous TBM performance prediction models for evaluation of TBM rate of penetration and advance been proposed. In brief, all the TBM performance prediction models can be divided into two distinguished approaches, namely theoretical and empirical ones (Rostami et al., 1996). The most common and recent works on this topic are summarized in Table 1. Currently, two models including Colorado School of Mines or CSM (Rostami and Ozdemir, 1993; Rostami, 1997) and Norwegian University of Science and Technology or NTNU (Blindheim, 1979; Bruland, 1998) models are the most recognized TBM performance prediction and prognosis models in use around the world."

Jan 1, 2016

By Philip K. Chan

Batu Hijau is a new copper and gold mine located on the island of Sumbawa in the Republic of Indonesia. This paper details the design and construction of the Batu Hijau overland conveyor, one of the most challenging efforts of the project. The 1.8 m wide, 5.6 km long conveyor has a design capacity of over 10,000 mtph and carries primary crushed ore through the steep mountains of Sumbawa, which necessitated a 160 m vertical downhill section, a 75 m vertical uphill section, ten vertical curves and one horizontal curve.

Jan 1, 2000

By Jim Dunn

For decades many of us who are associated with the mineral industry have tried to show the public its economic and strategic importance. Some of the mineral industry's proponents have been politically powerful figures and have been widely quoted. Yet, as measured by public opinion, legislative support, or almost any other standard, our efforts have been inadequate. It is apparent that a set of environmental beliefs that discredit industry, firmly held by a number of idealistic persons, has had wider coverage in the media and in schools than has the mineral industry's message. Although the fervor of our idealistic friends is often unfounded and, their stands unscientific, they must be considered seriously. Unless we address the issues in terms the idealists will understand, the mineral industry will have little influence on them or on the general public. A. striking thing is that, quite often, translation of idealists' views into action has been counterproductive. The reason is obvious. Excessive amounts of money and energy have been spent on relatively minor problems. The common result is that larger problems have been created. It may be possible to help anti-industry idealists understand their own dependence on minerals, and thus render their views more realistic, if they are shown more effective ways to reach their stated goals. If those goals can be shown to be held in common by all sensitive human beings -- including those in business and industry - the dialogue becomes one of how to achieve common ends. Individual mining companies acting by themselves have little possibility of success, and companies working in unison through trade associations have not been successful. Further, it is unlikely that industry in general can be successful in changing minds unless it seeks outside help. But friends among those who influence public opinion have been hard to find. Historically, help from media has proven difficult to get. Nor has enough help from educators been forthcoming. Yet, a war is going on in the technological, philosophical, and political trenches, even though much of the public is not aware of it. For the first time in years, there is row a significant and growing number of eloquent and brilliant thinkers on the side of free enterprise and industry, many of them environmentalists, but without the anti-industry mind-set. They have had remarkably little help from the private sector or even from the present administration. Industry may do far more for itself in the long run by encouraging these brave but bruised individuals and their organizations than by trying to work alone. These friends of free enterprise are working against a seemingly stacked deck relative to much of the media, the bureaucracy, and the educational system. However, despite their problems, their success to date has been remarkable. With more cooperation from industry they should do even better.

Jan 1, 1987

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By J. W. Merks

Spreadsheet software is an effective tool for simulating dynamic stochastic systems such as mineral processing plants. The two-product formula is used to show how to set up a Monte Carlo simulation in a spreadsheet template and how to calculate variances of dependent variables. The key to a reliable and realistic simulation model is to obtain unbiased estimates for all independent variables and variances in the set that defines the stochastic system. Monte Carlo simulation is also a powerful tool for optimizing sampling procedures, for applying sensitivity analysis and for designing and evaluating experiments.

Jan 1, 2000

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977