Search Documents

By David B. Cook, James R. Bieke

I. INTRODUCTION Lawyers are a cautious breed; and it might be expected that a paper concerning a broad and complex area of legal regulation, prepared by lawyers for presentation to a predominantly non-legal audience, would commence with several caveats. Ours are the following: First, we have written a broad (and, in some instances, simplified) overview of the regulatory system and of some of the more important requirements generally applicable to uranium mine and mill wastes in the United States. Our paper is not a legal opinion setting forth all of the governmental requirements that would have to be met by any particular mine or mill. Similarly, we do not imply that the requirements we mention are necessarily applicable to each and every mine and mill in the country; depending on the facts, some of the requirements may be inapplicable or avoidable through exemption or variance proceedings. Compliance decisions and strategies for particular facilities must be considered on a site-specific basis. Second, we have undertaken merely to describe the regulatory framework and some of the generally "applicable" requirements which have been promulgated and proposed by administrative agencies. We express no opinion on whether, under the U.S. Constitution and statutes, the existing and proposed agency regulations are valid in general or as applied to any particular mining or milling operation. There are, of course, procedures for judicial review of agency action; and newly promulgated environmental regulations have frequently been challenged, with varying degrees of success, before the courts. For us even to begin to consider such issues would expand an already forbiddingly long paper to totally unmanageable proportions. Third, in light of the subject of this Conference we have limited our paper to the legal framework and requirements applicable to uranium mine and mill "wastes" -- primarily mine overburden and waste rock and mill tailings (including waste tailings solution). We treat operating discharges (e.g., emissions from yellowcake drying) only peripherally. Fourth and finally, it is important to note that this paper, at least in so far as it concerns the specific requirements of particular regulations, will likely soon be out of date in some important respects. Despite

Jan 1, 1980

By Bruce R. Sutherland, Jim B. Ramsden, Gerry L. Bolton

Conductive metal powders are important building blocks for today's micro-electronic circuitry. Formulated into inks, they provide the interconnects needed to complete a complex integrated circuit and the means to enter the world of miniaturization. Traditionally, the inks have been based upon expensive metals such as silver, palladium, platinum and gold because of their excellent electrical conductivity and resistance to corrosion and oxidation. The use of a copper based ink, as an alternative to precious metal inks, recently has received considerable attention. Instability in the prices and limited supply of certain precious metal systems have driven up production costs, making the development of a lower cost copper system more attractive to manufacturers. However, lower production costs are on1 y real ized if performance and reliability can be maintained. While the development has been driven by cost, copper does offer some significant performance advantages over noble metal systems: conductivity as good as silver and 4W better than gold; leach resistance better than silver and equal to gold; stability at high frequencies better than gold or silver; strong film bonding characteristics; and compatibility with most solders. These benefits, however, do not come without cost. The inherently reactive nature of pure copper, while providing unique performance properties, makes it difficult to process. Unl i ke precious metals which can be fired in air, copper would oxidize and so requires special furnaces and atmospheres. Despite these difficulties, the transition from precious metal thick film systems to copper is gaining momentum. Manufacturers of high density, high performance circuitry are exploring the performance advantages of copper over gold and silver and the manufacturers of consumer products are considering the potential cost savings of copper over silver-palladium. Sherritt has developed a fine copper powder for this industry. Through association with the ink manufacturers, it has been found that performance properties of the ink vary with the physical and chemical characteristics of the powder. Production Process The production of very fine copper powders at Sherritt is based upon the disproportionation of cuprous ions as outlined in Equation [1] (1).

Jan 1, 1990

By Leonard W. III Joseph, William H. Buttermore

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health and- ministration (OSHA) are accepted by MSHA relative to coal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987

By K. Nagata, T. Kawashima, S. Tejima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service, port construction, trans-shipment, and environmental control. The major problem is the shipment of coal. Customary methods for bulk transfer must be improved and new systems developed. Slurry unloading has a key role in the new systems. This report reviews progress in slurry transportation research that has been done in Japan since the 1960s, when large-scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are focused on.

Jan 1, 1987

By Rob Dorey

The disposal of mine waste continues to be one of the main controlling factors in the economics and feasibility of project development. Particular to gold and precious metal mining, waste disposal is further complicated by the environmental and political implications of the use of cyanide. Regulatory compliance criteria have partially dictated and can be anticipated to further dictate the approach and methods of tailings disposal. To develop practical, economic, and environmentally acceptable tailings disposal systems within these criteria requires the use of common sense approaches and the application of available technology. Waste disposal is typically considered during the pre-feasibility stages of project evaluation. At this time, the main emphasis is on the economics and practicality of extracting the metal values from the ore. Frequently, the result of this is that the nature of the tailings and the ability to dispose of the tailings is prejudged. It is also frequently the case, however, that during the feasibility stage and project permitting, the requirements for tailings disposal become paramount.

Jan 1, 1998

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By Jean-Luc Cornet

Downhill, or regenerative conveyors have always been a challenge to the design engineer due to their natural instability under load. The last decade has seen the appearance of high tonnage, high negative lift conveyors with several hundred meters of drop. These conveyors have made necessary the development of new braking systems and intelligent drive controls to address their starting and stopping requirements under various load conditions. This paper describes the critical design criteria of large regenerative conveyors and some of the advances in mechanical braking systems and drive control technology developed by Conveyor Dynamics, Inc. (CDI) to address their specific requirements.

Jan 1, 1993

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

By Stephen Slot Odgaard, Simon D. Taylor

Phase One of Copenhagen Metro opened on October 19th, 2002 and is already a great success. 11 stations are open and Phase Two with 6 additional stations will open during 2003. Phases One and Two include 21 km dual track, whereof 10 km is in tunnel. 17 stations (six deep, three shallow, and eight above ground) will service passengers with trains running at 90 seconds intervals. This paper will discuss the various aspects of the Metro, where construction methods include TBM bored, NATM, Cut & Cover, Secant Piles and Diaphragm Walls.

Jan 1, 2003

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By Thomas E. Garnar

Zirconium and hafnium are the twin elements of the periodic table because they are always found together. They resemble each other so closely that hafnium was not discovered until 135 years after the discovery of zirconium. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and von Hevesy detected it using X-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO,) and less commonly as baddeleyite (ZrO,). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. During World War I, it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s, when Zircon Rutile, Ltd., began mining at Byron Bay on the east coast of Australia, that zircon was first used as foundry sand. Later in the 1940s, NL Industries and Humphreys Gold Corp. began production of zircon sands from fossil beaches in northeast Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties and as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by the Republic of South Africa and the United States. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, the former USSR, China, Thailand, and Brazil. The location of world zircon mines, baddeleyite mines, and undeveloped zircon ores are shown in [Fig. 1]. World production of zirconium mineral concentrates is shown in [Table 1].

Jan 1, 1994

By E. L. Mann, Robert L. Virta

Asbestos is a generic name given to six fibrous minerals that have been used widely in commercial products. The six types of asbestos are chrysotile, crocidolite, amosite, anthophyllite asbestos, tremolite asbestos, and actinolite asbestos (Table 1). Chrysotile is the asbestiform variety of serpentine. Crocidolite, amosite, antho-phyllite asbestos, tremolite asbestos, and actinolite asbestos are the asbestiform analogues of riebeckite, cummingtonite-grunerite, anthophyllite, tremolite, and actinolite, respectively. Although amosite is an acronym for the Asbestos Mines of South Africa (AMOSITE) and does not specify a mineral type, it generally is composed of cummingtonite-grunerite asbestos so the terms are assumed to be synonymous.

Jan 1, 1994

By C. P. Miller

In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about two years ago, approximately ten localities, representing several different types of nickel occurrences were sample, and about 1500 samples of plant and soil were collected. This report will briefly cover the data and results for two areas, and s summary of guides for prospecting.

Jan 1, 1959