Search Documents

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By Dan Wang, Qiuju Li, Xiao Guo

The chemical states and ions interaction were significant interest to understanding columbite mineral/acid solution interface dissolution and reaction. The present research work was focus to explore the specific cations ( Nb5+, Fe2+, Fe3+) distribution near the ferrocolumbite mineral/acid solution interface, and determine these cations leaching sequence in sulfuric acid solution. X-ray photoelectron spectroscopy had the potential to provide detailed dissolution information by resolving chemical state and ion distribution of ferrocolumbite during sulfuric acid leaching process. The binding energy decreased in sequence as Nb5+- O < Fe2+- O < Fe3+- O, and increased in sequence as Fe3+- SO4 < Fe2+- SO4 < Nb5+- SO4 which revealed Nb in ferrocolumbite mineral more easily leached comparing to Fe. The ratio of Fe2+- O/Fe3+-O on leaching residue decreased, and Fe2+- SO4/Fe3+-SO4 ratio increased as sulfuric acid contraction increasing suggested that the Fe2+ oxidized to Fe3+ and released Nb from mineral and dissolved into leaching solution. The ratio of Nb/Fe was lower 0.07 with sulfuric acid contraction increasing which meant Nb dissolution promoted by oxidation of iron. The dissolution mechanism of Fe element in ferrocolumbite mineral was Fe2+- O broken and generated Fe2+. Fe2+ was oxidized to Fe3+ in concentrated sulfuric acid leaching solution. The dissolution mechanism of Nb in ferrocolumbite was that Nb5+- O was directly digested by H+, and the released Nb5+ complex with SO4 2− ion formed cation − anion pairs. The coordination of formation Nb5+- SO4 pairs and oxidation Fe2+ in mineral could promote ferrocolumbite dissolution.

Aug 5, 2023

By Gordon R. Wicker, Peter V. Avotins, Steven S. Ahlschlager

Laterite ore slurries exhibit Bingham plastic behavior and can be characterized by the magnitude of their yield point and Bingham viscosity. These two parameters are affected by ore composition, solids concentration, and temperature and are used to predict the pressure drop in pipelines and heat transfer coefficients in shell-and-tube heat exchangers. In cycloning of laterite slurries, the calculated cut size is corrected by factors obtained from the rheological parameters.

Jan 1, 1979

By R. Venkataramani

Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. Nearly 90% of all metals and-mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today&apos;s business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. 1 Constant efforts are needed to improve upon productivity if the ore is to be economically mined.

Jan 1, 1970

By Raja V. Ramani, Wilson Miola

The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (i) the amount of quartz in thesamples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls are necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples. In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.

Jan 1, 1991

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007

By Antonio Jorge de Sousa

In order to compare several mining variants, on the point of view of the variability of the ore quality parameters, a conditional simulation technique is applied to a complex pyrite deposit (FEITAIS orebody, Portugal). Exploitation methods such as cut and fill and sublevel stoping are studied by the a.m. methodology. For each mining variant, it is assessed the influence of several mining operators on the variability of grades.

Jan 1, 1982

By Michael Drozd

The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application. a. Absorption b. Desorption (Stripping) c. Acid Washing d. Reactivation e. Carbon Handling ( carbon transportation, sizing, de­watering, etc.) Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. This parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability. Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operation in the United States have under taken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPL-Carbon Link is being used to attempt to fashion industry standards so that a common reference point came be establish for activated charcoal usage.

Jan 1, 2000

By Terry M. Hertel

The chemistry of waters processed by Acid Rock Drainage water treatment plants can affect the Total Suspended Solids quality of the plant effluents. The sulfate ions in the ARD water will combine with the calcium ions from the lime that is used to adjust pH to form calcium sulfate. When the sulfate content of the waters to be treated is greater than about 1400 parts per mil­lion, the resulting calcium sulfate concentration will be approx­imately 2100 parts per million. This concentration is above the saturation point for calcium sulfate, and the salt will drop out of solution until the concentration falls below the saturation point. This "salting" phenomenon affects the total suspended solids of the treatment plant effluents by virtue of the fact that the salts will report to the filtration apparatus used for the analy­sis. This scenario is exacerbated as an effluent sample ages. Zortman Mining's water treatment plant effluent was being affected by "salting" during the spring and summer of 1995, and it seemed as though the effluents were exceeding the TSS lim­its; for no obvious reason. A testing program was initiated to verify an observation that "salting' was taking place. Treatment plant samples were collected and allowed to age, with TSS analyses being performed every day that the samples aged. Synthetic solutions were also prepared to study the "salting" phenomenon.

Jan 1, 1996

By Mandira Madhuchhanda, N. B. Devi, P. C. Rath, R. K. Paramguru, K. Srinivasa Rao

An experimental investigation of the dissolution of three base-metal sulfide minerals, namely, CuFeS2, ZnS and PbS, in hydrochloric acid medium in the presence of manganese dioxide is reported. Polarization measurements and leaching studies were employed in the study. Dissolution occurred in the following three ways: by the cyclic action of the Fe3+/Fe2+ redox couple, by galvanic interaction between Mn02 and the sulfide minerals, and because of chlorine evolution from the system. The later two routes were found more effective at higher HCI levels. PbS appeared to be oxidized easily, whereas CuFeS2 was the most difficult to dissolve. ZnS dissolution fell in between PbS and CuFeS2.

Jan 1, 2002

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. &apos;The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By K. N. Santini

The evaporite deposit at Searles Lake consists of alternating brine-saturated saline beds and saline-bearing mud beds. Three major subsurface brine-saturated saline horizons have been identified by private companies and the U.S. Geological Survey. They have been termed, from bottom to top, the Mixed Layer, Lower Salt, and Upper Salt. The important water-soluble components (Na, K, Mg, CO3, HCO3 , SO4, Cl, and B407) are either in brines or have combined to form the following minerals: halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, northupite, sulfohalite, glaserite, etc. Kerr-McGee Chemical Corp., the current operator at the lake, selectively pumps interstitial brines from each of the major horizons to feed its three chemical plants. As the pumping continues, brines are continuously replenished within the deposit by dissolution of the minerals through natural recharge or artificial fluid injection (solution mining). The brines are processed to produce a variety of chemical products, which include sodium carbonate and sulfate, potassium chloride and sulfate, sodium borate, and boric acid. The Anaconda Minerals Co. has been evalua¬ting potential domestic trona acquisition since 1981. We have evaluated various properties in the Green River, Wyoming trona district, and Owens Lake and Searles Lake in southern California. In 1983, we purchased with our joint-venture partner, Leslie Salt Co., the southern portion of Searles Lake from Occidental Petroleum Corp. Since mid-1983, Anaconda has been conduct¬ing a small exploration-drilling program at the property. The initial core holes were drilled along and adjacent to the existing access road. In 1984 we used an all-terrain drill rig to gain access to drill sites on the playa where no roads exist. The use of this equipment proved to be highly successful. The drill program consists of coring to an average depth of 450 feet and collecting brine samples from potentially commercial horizons. The brine samples are collected by setting a packer and swabbing the hole. The core is logged and split lengthwise; one-half is submitted to our Tucson Geoanalytical Laboratory for semi-quantitative mineralogy by X-ray diffraction and the following suite of chemical analyses: Na, K, Mg, C03, HCO3, SO4, Cl, B407, Li, H20 insolubles, and acid insolubles. Additional test work for selected core samples will include effective porosity and horizontal permeability determinations. The brine samples are subjected to the same suite of chemical analyses (minus insolubles) as the core samples. In addition, specific gravity is also determined. Both cross sections and isopach maps are being constructed. The hydrological characteristics of the potentially commercial horizons are also being investigated.

Jan 1, 1987

By A. Venkatachalam

Spinel ferrites, like NiFe2-2x Znx Ti4 O4 Fe CO1.5 Ge0.5 Tix O4, Ga1-x Fex Ni CO O4, Nil-x Fex Mn2 O4 have been prepared using the respective metal oxides in Stoichiometric quantities, by the ceramic method. The oxides were homogenized in acetone medium, pelletifed by using poly vinyl acetate as the binder. They were fired at 1000°C for 100 hours for compound formation. Chalcogenide spinels such as Zn1-x Cux Cr2 Se4 where 0=x=l and Cu1-x Fex Cr2 Se4 where 0=x=0.3 have been prepared by using 99.99% pure elements and then fired at 1000°C in quartz ampoules under vacuum conditions. X-ray diffraction studies of these compounds indicated a single cubic spinel phase. DC resistivity studies of the compounds were taken between 300-700K using LCR bridge by two probe technique. Thermo-electric power measurements were taken between 300-500K for all the compounds. Initial susceptibility studies have been carried out using a low field (0.506) and from which the nature of magnetic dimains and Curie temperatures were determined. Magnetic hysteresis measurements were carried out at 300K and at 80K, using alternating current hysteresis loop tracer, at 2K02 field. Mossbauer spectral measurements were carried out using Co57 source embedded in a copper matrix and an absorber containing 0.3 mg/cm2 of the sample. The spectra has been fitted by Mossfit Program. The catalytic effect of the spinel ferrites NiFe2-2x Znx Tix O4 where 0=x=1 has been studied by using the model reaction of decomposition of H2O2 at temperatures from 40°C to 70°C. It was found that the spinel oxides were found to possess poor catalytic activity.

Jan 1, 1990

By Ulises Deveze T.

The coal company Minerales Monclova, S.A. (MIMOSA), the owner of the Mimosa R Line, is a subsidiary company of Altos Hornos de Mexico, S.A., the largest steel plant in Mexico with an annual capacity of 2.5 million metric tons of steel ingots. The raw material&apos;s which are used in the steel plant are provided by the following companies: La Perla Minas de Fierro, S.A., iron ore; Cia. Minera de Guadalupe, S.A., Cia. Carbonera La Sauceda, S.A. Cia. Minera La Florida, S.A., and Minerales Monclova, S.A., which provide the coal used for coke, and altogether constitute the industrial group AHMSA. The coal property of Minerales Monclova, S.A. is located in the Sabinas coal area in the northwestern part of the Sabinas basin.

Jan 1, 1974

By Fan Yang, Meigui Yi, Lan Xiang, Zhuoying Yang

This paper reported the calculation of the reaction heat in titanium-bearing blast furnace slag (abbreviated as TBFS)-H2SO4 system based on estimation of thermodynamic data of CaTiAl2O6 by mechanical mixture model. The thermodynamic analysis indicated that CaTiAl2O6 was more stable than the corresponding ternary oxides as CaO·TiO2, CaO·Al2O3, and Al2O3·TiO2. TBFS-H2SO4 system was highly exothermic since all of the reactions involved in the system were exothermic. For example, the increase of temperature from 25 to 200°C led to the increase of the release of the reaction heat in TBFS (100.0g)-H2SO4 system from 181.28 to 189.73kJ. Eighty-five to 90%of the reaction heat in TBFS-H2SO4 system was contributed by the reactions among CaTiAl2O6, CaTiO3, CaMgSi2O6, and H2SO4.

Feb 1, 2021

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

The United States is being invaded... by foreign capital: marks, francs, pounds, yen, lire, riyals, you name it: On almost any given day the Wall Street Journal will contain a new report on a department store, newspaper, bank, hotel, agricultural land, supermarket chain, et a1 being bought into by overseas investment. Xenophobic reaction to this revised national condition has begun to set in. Several farming states have and are introducing legislation to monitor foreign land buying. In Congress a mandatory reporting requirement for foreign purchasing is currently under study. In a relatively short period the country has reverted from world leader- ship in overseas acquisition and involvement to become itself one of the prime investment opportunities in existence. Interestingly enough, one of the industries where this changed status has become most apparent and pronounced is within that small/regional/segmented/low value-to-weight bulk commodity enterprise ranked as the backbone of the nation&apos;s construction activity. U.S. cement making is not only undergoing internationalization in its ownership, but also in its product, equipment, and engineering expertise.

Jan 1, 1979

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982