Search Documents

By Steve Axen

In situ mining is now considered an alternative mining method for some ore bodies. The in situ operation consists of a well field designed from reservoir properties and geological information; the wells for such a field are then drilled, cased, and cemented, using good designs and practices to eliminate future problems. Injection and production (recovery) systems are required to be corrosion resistant. Hand in hand with the mining operation is the metal extraction plant, the entire operation offering an environmentally acceptable method for metal recovery. Great opportunity exists in this field for mineral engineers; presently, they must borrow knowledge from other fields, since the schools have not yet addressed this specialty.

Jan 1, 1979

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Shotcrete can be defined as spray-applied concrete with a maximum size aggregate in excess of 9.5 mm (0.375 in.). The concept evolved from guniting, which uses smaller aggregate and generally produces concrete with poorer physical properties. The larger aggregate used in shotcrete requires less water in the mix, while offering larger bonding surfaces, thus imparting greater tensile and compressive strengths. TYPES OF MACHINES Two basic designs of shotcrete machines in general use are the wet or prehydrated zero slump and low slump type, and the dry or nozzle hydrated machines. Fig. 1 shows a typical zero-slump machine in a con¬figuration commonly used for small-volume require¬ments. The prehydrated zero-slump machine mixes exactly proportioned batches in a sealed pressurized chamber. "Slugs" of hydrated shotcrete mix and com¬pressed air are sent through a distribution hose to the nozzle where the wet mix emerges as a spray. The spray is directed onto the rock surface by the nozzle operator. The low-slump machine is similar, except that a thick slurry mix of aggregate is delivered throughout the distribution hose to the nozzle. Fig. 2 shows a typical low-slump shotcrete machine used in moderate-volume applications. The nozzle-hydrated shotcrete machine accepts a premixed "dry" (4 to 6% moisture) batch of aggregate and cement. A constant feed of this mix is directed by compressed air through the distribution hose to the nozzle. At the nozzle, water for hydration is introduced into the emerging spray. The hydrated mixture is di¬rected onto the rock surface by the nozzle operator. Fig. 3 shows a typical dry-mix machine. The major difference between the two basic machine designs is the consistency of the shotcrete quality. Pre¬hydrated machines have high degrees of consistency and produce high-strength concrete, resulting from their ability to produce exact mixtures of zero or low-slump concrete within the machine. Nozzle-hydrated machines tend to produce poorer quality concrete because of the difficulty in controlling the water content at the nozzle. Water input essentially is an art. As such it is not precise, and the shotcrete produced is of variable quality. MATERIALS HANDLING Materials handling presents a problem to either type of shotcrete machine. At times considerable quantities

Jan 1, 1982

By Kevin Schraden, Andrea Pezzi

environmental and social/political changes the world is currently experiencing. Three of major challenges facing the mining industry today are: water scarcity, unpredictable weather conditions that generate a risk of tailings dam failures as well as the correlating social pressure and government regulations that prevent the development of new or expanded tailings dam projects. It is estimated the total number of active, inactive and closed storage facilities globally is over 8,500 containing over 217 km3 of tailings (46% are from copper mining)1 which at some point will need to be addressed. Technologically, there are several solutions for tailings management, including conventional ponds, thickened tails, paste backfill and filtered dry stack tailings. The use of pressure filters, for tailings dewatering is currently being evaluated and often selected as the preferred technology where dry stacking is the chosen solution for residue disposal. This is mainly due to the pressure filters ability and flexibility to address and achieve the current challenging aspects of tailings processing including: • Extremely high capacities of >80,000 dry tons/day • Lower ore grades which require finer grinding and result in a higher amount fine fractions and clay content • Residual moisture targets required for the geotechnical specifications for dry stacking

Feb 1, 2024

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By E. W. Sawyer

Gelling-grade attapulgite and sepiolite clays are employed as thickening agents for the preparation of ionically contaminated drilling fluids where the use of fresh water clays are unfeasible or impossible. Attapulgite and sepiolite are nonswelling clays that can be dispersed and reflocculated by mechanical and chemical means to increase the viscosity of fresh water, salt containing waters, gypsum contaminated waters and fluids containing cement. Such gelled systems are quite stable in viscosity properties and can be further treated with other necessary additives such as thinners, water loss reducers, weighting agents, surfactants, etc. Many of the oil well drilling fluid practices have influenced such technologies as water well drilling, foundation drilling and waste disposal. The use of salt water gelling clays in these fields will be described and compared to oil well drilling.

Jan 1, 1986

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By Terry I. Mudder

Metal complexed cyanides in wastewaters form as a result of interactions of free cyanide with metals present in the wastewater and exhibit varying degrees of stability, toxicity, and treatability. Thiocyanate, a pollutant commonly found in cyanide bearing wastewaters, is formed through the interaction of free cyanide with sulfur containing species (i. e. pyrrhotite) both present in the wastewater. In certain industrial processes, such as the beneficiation of gold and silver, cyanide is an essential reagent. Since free cyanide, complexed cyanides, and thiocyanate are potentially toxic to humans and aquatic organisms, these compounds must be removed from wastewaters prior to their discharge into surface or ground waters serving as potential potable water sources, marine or fresh water habitats

Jan 1, 1984

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By V. F. Swanson

A petrographic study was made of the type and sources of mineral contamination occurring on phosphate rock products from Florida. Emphasis was placed on contaminants in the screened rock (+1 mm) since this portion of the product undergoes no physical beneficiation except for scrubbing to remove slimes. Since iron and aluminum con- tent of the finished product affect the salability, special emphasis was placed on identifying types and sources of these contaminants and relating chemical composition to visual characteristics. Wavellite derived from the overburden was the major aluminum contaminant with some aluminum being included as secondary clayballs. Iron occurred as phosphates in the overburden, and as colloidal oxides included in the phosphate pebbles. Chert and limestone contamination were derived from the Hawthorne formation underlying the phosphate matrix.

Jan 1, 1969

By A. L. Frank, Benton

INTRODUCTION The selective sensitivity of plastic nuclear track detectors (PNTD's) to low energy 4He particles in an environment which also contains gamma and beta radiations has made these detectors prime candidates for the dosimetric measurement of the concentrations of radon and its daughter products in mine air. Their passive, integrating mode of measurement, small size, low weight and inexpensiveness are attractive characteristics for large scale personnel dosimetry. The detectors can be used in either active or passive dosimeters. In active devices, the PNTD is placed in close proximity to a sampling filter. The filter collects, from a calibrated air flow, all the daughter nuclei which are in suspension. As the daughter nuclei pass through the decay chain, through 214Po, a fraction of the 4He particles emitted are registered as latent tracks in the plastic. In passive devices, the PNTD is placed in direct contact with the ambient air containing the radio-nuclei concentrations to be determined. The active dosimeters have the advantage of excellent sensitivity, and the measured track densities yield very close approximations to accumulated Working Level (WL)** exposures. They have the disadvantage that the simplicity of the passive PNTD is lost, since a battery-driven constant flow-rate air pump is a necessity. The passive dosimeters are simple in construction and use, but they have the disadvantage that WL exposures are not directly measured and certain assumptions concerning radon and daughter equilibrium conditions must be made in determining WL exposures from the measured track densities. Also the sensitivities, in track densities per Working Level Hour (WLH) exposure, are much less than for active dosimeters. Dosimeters of both types have been investigated. Passive devices have been tested extensively both in the laboratory and in mines. Active devices have been laboratory tested. In our earlier measurements, cellulose nitrate plastic detectors were used exclusively, since this material had the highest sensitivity of the PNTD's then in use. When the properties of CR-39 plastic were discovered (Cartwright, 1978; Cassou and Benton, 1978), this material was used, where possible, to take advantage of its superior sensitivity. The results of our earlier work have previously been published (Frank and Benton, 1977). * Research sponsored by the Bureau of Mines, U.S. Department of Interior, under Contract No. JO-188003. ** A Working Level is defined as any combination of the short-lived radon daughters containing 1.3 x 105 MeV of potential 4He-particle energy per liter of ambient air. PASSIVE DOSIMETRY In the earliest testing of PNTD's for passive WL dosimetry, a single strip of cellulose nitrate plastic was used to determine the total cumulative 4He-particle activity in the air of simulated uranium mine and uranium mine environments (Rock, 1968; Rock [et al], 1969; White, 1969). The measurements yielded a close relationship between track densities and WL exposures in a controlled, static environment, but poor accuracy in the active mine tests. It was assumed that equilibrium differences contributed largely to the variations found. The response of PNTD's to airborne 4He-particle emitters, derived by Lovett (1969), demonstrated that detectors such as cellulose nitrate, which has a sensitivity cutoff at 4He-particle energies below the emission energies of radon and its daughters, are equally sensitive to the activity concentrations of radon, 218po(RaA) and 214Po(RaC'). Since radon does not contribute to WL as it is defined, and since, under normal ventilated uranium mine conditions, the radon activity constitutes about 40% to 70% of the total 4He-particle activity, the WL exposures calculated from measured track densities are very sensitive to the particular radon daughter equilibrium conditions. Also, the detector does not weight the individual daughter activities in proportion to their importance to WL. The equation for WL is WL = 0.00103C2 + 0.00507C3 + 0.00373C4 (1) where C2, C3 and C4 are the activity concentrations of RaA, RaB and RaC-C', respectively, in pCi/[L]. The detector leaves C3 unmeasured and weights C2 and C4, equally. [This problem has been approached by Domanski et al (1975, 1979), for some non-uranium mines, by measuring equilibrium conditions throughout the mines to determine a mean value for A, the inverse of the Working Level Ratio (WLR = 100 WL where C1 is the activity of radon-222 in pCi/[L].) The distribution of values allowed Domanski to determine probable errors in calculating WL exposures from track densities. However, measurements of equilibrium conditions in U.S. uranium mines (Breslin et al, 1969; Holub and Droullard, 1978) indicate that this method would not be accurate enough for uranium miner personal dosimetry.] A two-element dosimeter was designed at our laboratory to compensate for equilibrium variations. The first element is a radon detector; the second is a detector for the total 4He-particle activity in the ambient air, just as in the single element dosimeters cited above. The addition of the radon detector allows the equilibrium conditions for the individual nuclei to be determined, given certain assumptions concerning the interrelationships between the nuclei concentrations in mine air. The two detectors and the problems involved in calculating WL exposures from their measurements are discussed below.

Jan 1, 1981

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By R. E. Vivas, J. Garcia

"INTRODUCTION Freeport-McMoRan is a leading international natural resources company that operates large, long-lived, geographically diverse assets with significant proven and probable reserves of copper, gold, molybdenum, cobalt, oil and natural gas. Freeport-McMoRan is the world’s largest publicly traded copper producer and largest producer of molybdenum. The Sierrita mine is an open pit truck and shovel operation from which copper and molybdenum are produced. An important key to Sierrita’s success lies in their ability to realize their plans in the field. In certain circumstances, the mine plans are not achieved, and the operation fails to meet its targets which is an issue revealed in reconciliation reports. This technical session discusses the methodologies and procedures used at Sierrita to monitor the implementation of the mine plans, measure the performance of the operation and reduce the variance between plan and actual. Ensuring the operation stays on target is vital so mine productivity and profitability can attain its maximum potential. PROJECT OVERVIEW The Sierrita mining complex is located in Pima County, approximately 20 miles southwest of Tucson, Arizona as shown in Figure 1. The first mining claims at Sierrita date back to the late 1800s while underground mining activities started in the early 1900s. However, open pit development of Sierrita began more than 50 years ago to become the modern mining complex it is today. In 2009, Freeport-McMoRan purchased the adjacent Twin Buttes copper mine, providing significant synergies in the Sierrita minerals district. This venture included the potential for expanded mining activities, operations growth for mining copper and molybdenum, and reclamation activity. It should be noted that in addition to copper and molybdenum, the Sierrita mine produces rhenium which is a rare and highly value metal. The ore deposit contains oxide and sulfide mineralization. The oxide ore is delivered to the leach process while the sulfide ore is routed to the crusher and mill circuit 4,700 jobs on Arizona’s economy Freeport-McMoRan partners with the communities near Sierrita to provide programs that contribute to their sustainability"

Jan 1, 2015

By D. R. Schricker

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment.

Jan 1, 1990

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

By Harold L. Lovell

Problems associated with fines (minus 6 mm, 1/4-inch) production, preparation, and utilization have long plagued the coal industry and are now more acute than ever. Continuous deep mining systems create more fines which have moisture; content greater than natural levels from dust control spraying and often add substantial levels of mineral matter due to mining selectivity constraints. Frequently, during preparation, more -fines are developed to achieve improved component liberation. Coal consumers often specify small sizes whether for carbonization, combustion, or conversion. Wet beneficiation systems process fines by several' types of unit operations, but usually must also incorporate costly and complex dewatering systems to reduce the moisture content of the products. Existing pneumatic preparation systems are constrained between product equality and yield by the sharpness of separation. These limitations become more severe with decreasing particle size and increasing feed moisture content. Control of particulate emissions, both process and fugitive, during pneumatic preparation, can be forbidding. A pneumatic preparation-process which would overcome these constraints, could be most enticing. The DryFlo system is being evaluated to quantify performance characteristics as regards these constraints.

Jan 1, 1976

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Madan M. Singh

It is estimated that through 1975, there were 1.69x109 m2 (418 000 acres) of urban land threatened by potential subsidence due to mining with a value of over $12 billion (19;3 dollars; USBM, 1979). With increased coal production to meet the energy needs of the nation, both these figures may be expected to increase. Hence greater attention to controlling surface damage due to subsidence is merited. In fact, the Surface `lining Control and Reclamation Act of 1977 (SMCRA) (Public Law 95-87) mandates that underground coal mining operators "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, ..." The term "subsidence," as used in this paper, implies the total phenomenon of surface effects associated with the mining of minerals, and not only vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016