Search Documents

The Colorado portion of the Rio Grande rift is clearly defined physiographically from the south in the San Luis valley northward to the latitude of Leadville where sediments of the Dry Union Formation (Tweto, 1961) accumulated within the subsiding rift zone. To the north of Leadville is a system of faults active in the late Tertiary, including the Mosquito fault that offset a portion of the Climax mineralization (Wallace et al., 1968). Tweto (197B) describes remnants of Dry Union Formation against the Mosquito fault north of Dillon in the Blue River valley, so it is apparent that the rift and associated sediments extended well to the north of Leadville. Kelley (1952, 1954, 1956) and Chapin (1971) have noted in New Mexico that the Rio Grande rift is a series of en echelon basins, offset to the east, with constrictions connecting them (Fig. 1). In Colorado the structural basins are offset to the west. The net effect of all the rift zone basins in New Mexico and Colorado is an arcuate pattern (Fig. 1) abutting the Colorado Plateau and Sari Juan Volcanic Province on the west. The width of the rift system gradually decreases northward to about Leadville where rift definition is not apparent.

Jan 1, 1987

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By C. L. Schneider

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance and is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require the estimation of a large number of parameters unless a structural model of the ore texture can be used. A very simplified textural model based on the use of the modified Andrews-Mika diagram and the PARGEN simulation of multi-phase particles has been formulated and is used to simulate the behavior of a continuously operating laboratory ball mill. A sensitivity analysis for this mill has been done to show the likely effect of model approximations on the predicted liberation spectrum which will be measured.

Jan 1, 1992

By O. A. Velasquez, A. R. Kumar

"Dust generated on underground mechanized coal mining faces is a health and safety hazard. Continuous miners deployed underground usually have an integrated flooded-bed dust scrubber mounted onto the machine that arrests the generated dust from close to the face and cleanses the air around it. However, the impingement screen might get clogged depending on the coal seam being worked. This necessitates the cleaning of the screen which in turn, reduces the overall availability of the scrubber and, hence the continuous miner. A novel non-clogging screen has been developed at the Department of Mining Engineering, University of Kentucky. The proposed impingement screen is built up of three individual aluminum screen units 1.5 mm thick and separated by 3 and 2 mm respectively. The screens have long vertical slits measuring 6 mm. A water spray continuously keeps the screen wet and provides for the filter element to arrest the dust particles. The slits force the dust-laden air to make sharp turns. The dust particles cannot change directions rapidly, impact one of the three screens and are separated out based on their momentum. Preliminary computational fluid dynamics (CFD) models have indicated significant cleaning efficiencies in the respirable range at the expense of much lower pressure drops. Results indicated by CFD models and supported by laboratory experiments have been discussed in this paper.ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research. Dr. Thomas Novak, Professor of Mining Engineering, is also acknowledged for his continued support and encouragement. INTRODUCTION Continuous miners are ubiquitous in coal mining around the world. The miners are operated against bling headings, ensuring adequate flow of air at the face could be difficult. The minimum requirement of ventilation airflow quantities at those coal faces are legislated to dilute dust generated to harmless levels. New dust rules promulgated recently have further called for lower exposure levels of personnel working underground (Courtney) (MSHA, 2014) (NIOSH, 2010). Water sprays are also installed at strategic locations and serve as powerful air-movers. The sprays capture some amount of dust generated while cutting. In addition to this, usually, all continuous miners are equipped with a flooded-bed dust scrubber as shown in Figure 1 to capture the dust from close to the extraction drum (Chao & De-sheng, 2000) (Wala, Vytla, Huang, & Taylor, 2008) (Organiscak & Beck, 2010)."

Jan 1, 2018

By K. T. Valsaraj

The separation process called solvent sublation for the removal of two hydrophobic compounds (penta-and tri-chlorophenols) from the aqueous phase is discussed. A steady state mathematical model for the process is discussed. The process was conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1992

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By Donald E. Steif

The Tower Mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine, its operation, application, and performance for wet grinding.

Jan 1, 1984

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

"Mining of ore bodies that are located at great depths enforces long distances to move the excavated rock masses to the surface. The excavated rock mass contains not only ore that can be economically extracted from the face but also waste, which is usually discarded several steps further downstream in the process. As a result, a large amount of rock is transported to the surface, influencing the costs at which the ore is produced. Reducing the amount of waste rock being transported to the surface by introducing a near-to-face sorting plant would improve the in many cases strained transport system in the deep mine. In this study, one of Boliden’s cut-and-fill mines was analysed with respect to the challenges related to rock transportation and increasing mining depth. The study aims to evaluate the potential use of a new near-to-face sorting system in the operating underground mine. Discrete event simulation was used to study and analyse the rock transportation system with and without the near-to-face sorting plant. The paper shows how the underground rock transportation system and the production were influenced when the near-to-face sorting equipment was added into the current system. INTRODUCTION The locations of waste rejection in the mining processes and the cost of removing waste from the system compared with the cost and energy necessary for further comminution are important parts in the material handling system (Bowman and Bearman, 2014). In an underground mine, longer material transportation distances generate the need for further investment in the mobile fleet and ancillary equipment in order to reduce the waste from the material handling as early as possible. One of the ways of reducing the waste (coarse particle size) in material handling is by use of pre-concentration. The benefits of pre-concentration are well known (Schena et al. 1990; Feasby, 1995; Peters et al. 1999; Klein et al. 2002), as well as the factors governing the feasibility of underground pre-concentration (Peters et al., 1999) and the mining integration issues (Klein et al. 2003). In the Onaping Depth orebody in Sudbury, Ontario the study of implementing the pre-concentration resulted in increased capital costs of 6% and a reduction in the operating costs of between 20-40% (Bamber et al, 2004). In this paper, the effects on the production and the transportation system of implementing underground pre-concentration by means of a near-to-face ore sorting plant in the Kristineberg mine are modeled and analyzed using the AutoMod tool. This tool is based on discrete event simulation (DES) (Banks, 2004), allowing high flexibility in customization and enabling the user to view the production of the system before ore sorting plant integration. The sorting plant selected in the simulation is built from modules. The material is fed by conveyor and goes through the comminution, classification, sorting and service processes after which the waste is redirected to backfill headings via trucks. The system mechanically ejects the particles from the feed stream on the basis of the information obtained from both the XRT sensor’s signal and 3D laser scanner based on both density and rate of refraction of light within a particular mineral. The sorting plant could pre-concentrate the metal ore up to 300 mm size. The plant requires little auxiliary infrastructure, is easily modularized for underground installation and can be easily relocated to different areas."

Jan 1, 2016

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By W. H. Jang

Although surface chemistry fundamentals of semi-soluble minerals have been studied by many researchers, detailed understanding of these systems is still incomplete. In-situ FT-IR/IRS techniques have recently been used to successfully describe the adsorption of carboxylates at semi-soluble mineral surfaces. However, the wetting characteristics of these adsorbed films require further consideration. In this regard, the hydrophobicity and stability of transferred Langmuir-Blodgett (LB) monolayers of fatty acids at fluorite and calcite surfaces has been studied by contact angle measurements with polar and apolar liquids. Generally, it was found that the transferred LB monolayers of fatty acids at a calcite surface are unstable whereas such monolayers transferred at a fluorite surface are stable, as revealed from advancing and receding contact angle measurements. These results are believed to be due to the incomplete reaction of fatty acid monolayer at the calcite surface. In addition it was found that a closely packed well-ordered stearate monolayer with good hydrophobicity, equivalent to that of a transferred LB monolayer, can be formed at fluorite surfaces by spontaneous adsorption and self-assembly from aqueous solutions.

Jan 1, 1995

By George D. Haley

This report will be given in two sections. The first sec¬tion outlines techniques and equipment to form almond shaped fluorspar briquettes by means of briquet presses, and the second section outlines techniques of the balling disc. PART I - BRIQUET PRESSES Fluorspar has been briquetted for a number of years and the so called "peach pit" briquet is known to many steelmen. Present production is estimated at over 100,000 tons annually. Slide 1 shows an assortment of various sizes and shapes of briquettes. It is possible to form fluorspar into almost any configuration of briquet. For safety on the melting floor, pillow type briquets are preferred. Ease of mechanical handling and durability of the product are facil¬itated by an almond shape. The dimensions of the almond can vary from 1-in. to 1-1/2-in. in length, from 13/16-in. to 1-in. in width and from 1/2-in. to 1-in. in thickness. The type of equipment to pro¬duce almond shaped fluorspar briquettes is shown in Slide 2. Here we have a Komarek-Greaves and Company 300 ton briquettor equipped with almond rolls. This machine is capable of producing fluorspar briquettes at a rats of 30 tons per hour with power consumption of 35 hp per ton par hour.

Jan 1, 1969

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: ( 1) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold is so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfides and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By H. M. Breza

Recovery of phosphate concentrate has received increased attention as the existing mine and plant production capacity limitations of the Texasgulf Inc. Aurora, North Carolina Mine are reached. Improved mining techniques and mineral processing of waste streams offer a potential to increase overall phosphate production without major expansion of the Mining facility. Innovative processes have been or are being identified to maximize pit mining recovery and to minimize losses in waste streams, resulting in more effective use of the valuable phosphate natural resource. This paper will describe the various continuous recovery improvement programs being implemented to achieve this goal.

Jan 1, 1994

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill&apos;s product and the critical size in a SAG mill is examined.

Jan 1, 1993