Search Documents

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By R. O. Harma

Wet autogenous grinding is utilized in three iron ore concentrating plants operated by The Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping.

Jan 1, 1982

By Bruce C. Trent

In order to effectively model subsidence caused by underground openings, a two-dimensional computer code has been developed which couples near- and far-field response. The near-field is simulated by a discrete element block code and a finite difference code represents the continuum region in the far-field. The explicit equations allow rapid and inexpensive solutions to geometries which may lead to subsidence. Two sample problems are presented which illustrate the important features of the code.

Jan 1, 1979

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By III Cocanour

The line scan video photometer is a personal computer (PC) based, software-driven instrument which is used for the real time, on-line analysis of industrial process streams. The novelty of the instrument lies in the integration of its various components: (l) a true Red/Green/Blue (R/G/B) color video camera; (2) a unique, line-scan color sample and hold technique which provides a 4 to 20 mA analog signal to a commercial 12 bit analog to digital (A/D) converter; (3) software which converts data through a color absorbance algorithm to correlate elemental color to concentration; and (4) software-based control which utilizes color data, along with temperature and conductivity data to control process equipment. The photometer can be used for noninvasive analysis wherever color hues are representative of process variables such as chemical concentrations or mineralogy color reflectance. The line scan video photometer has been successfully demonstrated in solvent extraction/electrowinning (SX/EW) and ball mill circuits of copper producers.

Jan 1, 1996

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty's and early seventy's, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70's to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By Gabriel K. Nzulu, Lars Hultman, Per Eklund, Martin Magnuson, Abu Yaya, Prosper M. Nude, Hans Högberg

Pyrite is the most common among the group of sulfide minerals in the Earth and abundant in most geological settings. This gangue mineral in association with garnet, hematite, magnetite, and other sulfide minerals acts as an indicator mineral in the Kubi concession of the Asante Gold corporation in Ghana. X-ray diffraction (XRD), air annealing in a furnace, energydispersive x-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS) were applied to investigate the crystal structure, identify individual elements, permanence, transformation, and chemical/electronic properties of such pyrite. The study aims to identify individual elements and to gain an understanding of the surface reaction mechanisms, as well as the properties of precipitated pyrite particles observed during the hydrothermal formation of the ore deposit. XRD shows that pristine and annealed samples contain some hematite and quartz besides pyrite. Results from air annealing indicate that the relationship between pyrite and hematite-magnetite is controlled by temperature. EDX reveals that the sample has O and C as contaminants, while XPS in addition reveals Ba, Au, P, Al, and N. These elements are attributed to pyrite that bonds metallically or covalently to neighboring ligands/impurity minerals such as oxides, chalcogenide sulfides, as well as the gangue alteration minerals of magnetite and hematite in the pyrite sample. These findings suggest that during the hydrothermal flow regime, pyrite, pathfinder elements, and impurity minerals/metals were in contact with quartz minerals before undergoing hematite transformation, which thus becomes an indicator mineral in the Kubi gold concession.

Feb 27, 2024

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By Carl L. Morris

This short dissertation concerning "what the client expects from the engineer" is directed mainly at the design and construction of metallic ore concentration or beneficiation plants. However, practically the same conditions apply to the design and construction of cement and lime manufacturing facilities, with the exception that the latter facilities reflect the client's and engineer's concepts of customer service and in some cases reflect promotional considerations for the product manufactured and distributed. The client expects his engineering contractor to contribute in an efficient, cooperative, and economical manner current industry-wide know-how and experience to the specific project under consideration through the client's organization

Jan 1, 1969

By John Mastoris, Kostis Dragasakis, Kostas Kouklidis, Shkurtë Gashi, Halil Berisha, Jenuz Bulica

Titan Group’s environmental policy and Sharrcem’s Corporate Social Responsibility (CSR) are the driving forces behind the development and implementation of a comprehensive Rehabilitation Plan at Dimce Quarry, which is the main raw material source for Sharrcem Cement Plant since the 1970’s, located in the municipality of Hani i Elezit in Kosovo. Based on an Environmental Impact Assessment Study and the approved Mining Plan and also on the principles prescribed in the Guidelines on Quarry Rehabilitation, released by the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD-CSI), Sharrcem has adopted a quarry operation and rehabilitation process in line with the best practices in the mining and cement sector. This paper discusses the background for the development of the rehabilitation plan and the results of rehabilitation activities, as have been implemented over the last few years. The main objective of the progressive rehabilitation plan at Dimce Quarry is to restore the depleted pit and return it back to the original land owners for resettlement. To date approx. 3,4Ha of former mining area has been restored by backfilling and levelling of the depleted closed pit and returned back to owners, who have built their houses and turned it into a living area again. This Quarry has turned out to be a real composition and practical example of preserving and returning back the natural resources in a state compatible with the surrounding environment and with respect to the needs of the local stakeholders. The motivation for business to engage in rehabilitation activities in the first place lies in the belief that the development and implementation of a progressive and practical Quarry rehabilitation plan and restitution of the land will deliver significant environmental and social benefits that outweigh the long-term rehabilitation costs, while maintaining the company’s reputation.

Jan 1, 2017

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972